• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.2
• /
• pp.217-225
• /
• 2024

Even after the introduction of Global Maritime Distress and Safety System (GMDSS), many maritime accidents occur. A method of transmitting a rescue signal when a person falls into the water from a ship is currently being researched and developed in various ways, but no products have been developed that use frequencies allocated for maritime mobile service. Accordingly, in this study, we designed and produced a man-over-board (MOB) device by applying Group B AMRD technologies, which were adopted through the latest revision of the International Telecommunication Union (ITU). In addition, a receiver and user interface were built to verify the performance of the transmitter, and we confirmed that it can be used in conjunction with existing electronic charts. This MOB device satisfies the general and technical requirements of Group B AMRD using AIS technology and uses integrated components for miniaturization for easy portability in a maritime environment. We expect that it will achieve excellent AIS communication and be essential in rapid response and safety in emergency scenarios.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2024

To In this study, a nozzle which is designed to work as expansion device was installed in a refrigeration system and performance test was conducted. The nozzle has 0.8mm, 1.0mm, 1.2mm diameter and inserted in a body of the devices. System performance was compared with a electronic expansion device(EEV, electric expansion valve) and designed nozzles at the environmental conditions such as dry bulb and wet bulb temperature. To reduce energy loss in the evaporator, a nozzle was inserted into the evaporator. In the comparison test, the opening of the EEV was adjusted to the same diameter as the 3 nozzles, and the experiments conducted at a 27℃ dry bulb temperature and 19.5℃ wet bulb temperature with 50% relative humidity as defined at KS C 9306 standard. To find out the effect of the environmental condition, the bulb temperature was varied 5 degree lower and higher than the standard condition temperature with the same relative humidity condition at 50%. The air flow rate to the evaporator was also changed 4, 7 and 10 m³/min. As results, the temperature drop in the nozzle was 153% higher than that of the EEV and the enhancement of the performance(COP) was up to 125.7% if install the nozzles in the refrigeration system. The highest performance was obatained at 1.0mm diameter nozzle.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.17 no.4
• /
• pp.213-220
• /
• 2024

This paper proposes an optimization strategy for performing Federated Learning between devices and edge clouds using WebAssembly (WASM). The proposed strategy aims to maximize efficiency by conducting partial training on devices and the remaining training on edge clouds. Specifically, it mathematically describes and evaluates methods to optimize data transfer between GPU memory segments and the overlapping of computational tasks to reduce overall training time and improve GPU utilization. Through various experimental scenarios, we confirmed that asynchronous data transfer and task overlap significantly reduce training time, enhance GPU utilization, and improve model accuracy. In scenarios where all optimization techniques were applied, training time was reduced by 47%, GPU utilization improved to 91.2%, and model accuracy increased to 89.5%. These results demonstrate that asynchronous data transfer and task overlap effectively reduce GPU idle time and alleviate bottlenecks. This study is expected to contribute to the performance optimization of Federated Learning systems in the future.

• Journal of Surface Science and Engineering
• /
• v.57 no.5
• /
• pp.368-378
• /
• 2024

The growing environmental concerns due to increased fossil fuel consumption have intensified the demand for sustainable and economically viable energy sources. Among the various energy storage devices, lithium-ion batteries (LIBs) are widely used in electronic devices and electric vehicles due to their high energy density and excellent cycle life. However, LIBs face challenges such as safety concerns due to side reactions, thermal expansion, and explosion risks, along with issues of limited resource availability and high costs. As a result, multivalent metals such as calcium, magnesium, zinc, iron, and aluminum are being explored as alternatives to lithium. Recently, there has been significant interest in developing aqueous zinc-ion battery (AZIB) due to their use of water as an electrolyte solvent, which enhances safety by reducing the risk of fire even in the event of a short circuit. Additionally, AZIBs offer benefits such as non-toxicity, fast ion conductivity, high volumetric capacity, and cost-effectiveness due to the abundance of zinc. Despite these advantages, AZIBs face challenges including dendrite formation on the zinc anode during cycling, leading to short circuits, corrosion, and hydrogen gas evolution, which can compromise battery performance and safety. This review discusses the underlying mechanisms of these issues and explores various strategies to stabilize the zinc anode and improve the overall performance of AZIBs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.188.2-188.2
• /
• 2015

The presence of the conduction interface in epitaxial $LaAlO_3/SrTiO_3$ thin films has opened up challenging applications which can be expanded to next-generation nano-electronics. The metallic conduction path is associated with two adjacent insulating materials. Such device structure is applicable to frequency-dependent impedance spectroscopy. Impedance spectroscopy allows for simultaneous measurement of resistivity and dielectric constants, systematic identification of the underlying electrical origins, and the estimation of the electrical homogeneity in the corresponding electrical origins. Such unique capability is combined with the intentional control on the interface composition composed of $SrTiO_3$ and $CaTiO_3$, which can be denoted by $SrxCa1-_xTiO_3$. The underlying $Sr_xCa1-_xTiO_3$ interface was deposited using pulsed-laser deposition, followed by the epitaxial $LaAlO_3$ thin films. The platinum electrodes were constructed using metal shadow masks, in order to accommodate 2-point electrode configuration. Impedance spectroscopy was performed as the function of the relative ratio of Sr to Ca. The respective impedance spectra were analyzed in terms of the equivalent circuit models. Furthermore, the impedance spectra were monitored as a function of temperature. The ac-based characterization in the 2-dimensional conduction path supplements the dc-based electrical analysis. The artificial manipulation of the interface composition will be discussed towards the electrical application of 2-dimensional materials to the semiconductor devices in replacement for the current Si-based devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.50-50
• /
• 2008

ZnO has been extensively studied for optoelectronic applications such as blue and ultraviolet (UV) light emitters and detectors, because it has a wide band gap (3.37 eV) anda large exciton binding energy of ~60 meV over GaN (~26 meV). However, the fabrication of the light emitting devices using ZnO homojunctions is suffered from the lack of reproducibility of the p-type ZnO with high hall concentration and mobility. Thus, the ZnO-based p-n heterojunction light emitting diode (LED) using p-Si and p-GaN would be expected to exhibit stable device performance compared to the homojunction LED. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducibleavailability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices with low defect density. However, the electroluminescence (EL) of the device using n-ZnO/p-GaN heterojunctions shows the blue and greenish emissions, which are attributed to the emission from the p-GaN and deep-level defects. In this work, the n-ZnO:Ga/p-GaN:Mg heterojunction light emitting diodes (LEDs) were fabricated at different growth temperatures and carrier concentrations in the n-type region. The effects of the growth temperature and carrier concentration on the electrical and emission properties were investigated. The I-V and the EL results showed that the device performance of the heterostructure LEDs, such as turn-on voltage and true ultraviolet emission, developed through the insertion of a thin intrinsic layer between n-ZnO:Ga and p-GaN:Mg. This observation was attributed to a lowering of the energy barriers for the supply of electrons and holes into intrinsic ZnO, and recombination in the intrinsic ZnO with the absence of deep level emission.

• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.272-278
• /
• 2007

In this paper, we report on the 2D (two-dimensional) simulation result of the DC (direct current) electrical and thermal characteristics of AlGaN/GaN HEMTs (high electron mobility transistors) grown on Si substrate, in comparison with those grown on sapphire and SiC (silicon carbide) substrate, respectively. In general, the electrical properties of HEMT are affected by electron mobility and thermal conductivity, which depend on substrate material. For this reason, the substrates of GaN-based HEMT have been widely studied today. The simulation results are compared and studied by applying general Drift-Diffusion and thermal model altering temperature as 300, 400 and 500 K, respectively. With setting T=300 K and $V_{GS}$=1 V, the $I_{D,max}$ (drain saturation current) were 189 mA/mm for sapphire, 293 mA/mm for SiC, and 258 mA/mm for Si, respectively. In addition, $G_{m,max}$ (maximum transfer conductance) of sapphire, SiC, Si was 38, 50, 31 mS/mm, respectively, at T=500 K.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.4
• /
• pp.419-432
• /
• 2010

Various torque generating devices have been developed and employed to apply a proper torque. These devices are usually calibrated by the manufacturer to apply appropriate torque levels for their specific implants and attachments. The purpose of this investigation was to determine and compare the accuracy of the torque controllers. In this study, 4 types of torque controllers were used; torque limiting device(TLD), torque indicating device(TID) and contra angle torque driver(CA), electronic torque controller(ETC). Digital torque gauge was employed to measure the de-torque value. Thirty cycles of tightening and loosening were repeated with each torque controller. All implant torque controllers have shown slight errors and deviations. The contra angle torque driver exhibited the most accurate data. In the limitation of this study, it would be recommended that the implant torque controllers should be checked whether uniformed and precise torque can be generated and a measuring error should be corrected.

• Membrane Journal
• /
• v.27 no.2
• /
• pp.154-166
• /
• 2017

Polymeric films for gas barrier applications such as food packaging and electronic devices have attracted great interest due to their cheap, light and easy processability among gas barrier materials. Especially in electronic devices, extremely low gas permeance is necessary for maintaining the device performance. However, current polymeric barrier films still suffer from relatively high gas permeance than other materials. Therefore, there have been strong needs to enhance the gas barrier performance of polymeric barrier films while keep their own advantages. Recently, graphene is highlighted as a 2D-layered material for gas barrier applications. However, owing to the poor workability and difficulty to produce in engineering scale, graphene oxide (GO) is on the rise. GO consists of oxygen-containing functional groups on surface with intrinsic 2D-layered structure and high aspect ratio, and it can be well-dispersed in aqueous polar solvents like water, resulting in scalable mass production. Here, we prepared GO incorporated polyimide (PI) nanocomposites. PI is widely used barrier polymer with high mechanical strength and thermal and chemical stability. We demonstrated that PI/GO nanocomposites could perform as a gas barrier. Furthermore, surfactants (Triton X-100 (TX) and Sodium deoxycholate (SDC)) are introduced to enhance the gas barrier performance by improving the degree of dispersion of GO in PI matrix. As a result, TX enhanced the gas barrier performance of PI/GO nanocomposites which is similar to predicted value. This finding will provide new insight to polymer nanocomposites for gas barrier applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.151-157
• /
• 2007

We have presented a compact two-wire helical antenna adopted an open stub in opposite to a feeding point, which is for a T-DMB antenna of mobile devices. By adjusting the length of the open stub or pasting a dielectric material on the open stub, the input impedance around 200 MHz, bands of the T-DMB, can be easily control, even though the total height of the antenna is less than 8 cm(0.053 $\lambda$ at 200 MHz). The operating mechanism of the antenna is explained by using equivalent circuits of two modes, an unbalanced mode and a balanced mode. Based on the analysis of the equivalent circuits, the effects of using the open stub are validated. Several proposed antennas have been fabricated and measured. One of the fabricated antennas has -10 dB impedance bandwidth of $196{\sim}204$ MHz(8 MHz) whose value covers one channel of the T-DMB(6 MHz). The measured $S_{21}$ of the antenna is -38.6 dB which is about 17 dB higher than that of a monopole antenna whose height is same with the proposed antenna.