• The Journal of the Korea institute of electronic communication sciences
• /
• 제11권5호
• /
• pp.473-478
• /
• 2016

In this paper, the MIS(: Metal-Insulator-Semiconductor) Capacitor with the nitrided-oxide by RTP are fabricated to investigate the carrier trap parameters due to avalanche electron injection. Two times turn-around phenomenon of the flatband voltage shift generated by the avalanche injection are observed. This shows that electron trapping occurs in the oxide film at the first stage. As the electron injection increases, the first turn-around occures due to a positive charge in the oxide layer. After further injection, the curves turns around once again by electron captured. Based on the experimental results, the carrier trapping model for system having multi-traps is proposed and is fitting with experimental data in order to determine trap parameter of nitrided-oxide.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.151.2-151.2
• /
• 2016

We characterized the n-type organic field-effect transistors (OFETs) with non-conjugated polyelectrolytes (NPEs) interlayers as the electron injection layer. Novel NPEs with various ions (Cl-, Br-, I-) improved the electron mobility from $5.06{\times}10^{-3}$ to $2.10{\times}10^{-2}cm^2V^{-1}s^{-1}$ in OFETs based [6,6]-Phenyl-$C_{61}$-butyric acid methyl ester (PCBM) when $PEIEH^+I^-$ spin-cast from 0.6% solution was deposited onto the PCBM layer. Reduced electron injection barrier (${\phi}_e$) at NPE/metal electrode interface was induced by dipole formation and led to increase the electron injection and transport. These findings are important for understanding how NPEs function in devices, the improvement of device performance, and the design of new materials for use in optoelectronic devices.

• Polymer(Korea)
• /
• 제36권4호
• /
• pp.519-524
• /
• 2012

Capacitance measurements of the polymer light-emitting diodes (PLEDs) with conjugated polyelectrolyte (CPE) electron transporting layers (ETLs) provide important information of device physics for understanding the function of CPEs as ETLs, together with current density-voltage-luminescence measurements. We investigated the counterion-dependent capacitance behaviors that present a highly negative or positive capacitance at the low frequency, and suggested different carrier injection mechanisms. Capacitance model study reveals that the electron injection mechanism can be described either by the dipole alignment scheme or by electronic charge carrier accumulation at the cathode/ETL/emission layer interfaces.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• 제5권1호
• /
• pp.27-32
• /
• 2006

Thermoplastic elastomer(TPE) has many advantages such as high flexibility, high elasticity and high elongation, etc. TPE is easily molded as plastic materials, therefore, many TPE parts are applied as home appliances and mechanical parts. However, its mechanical properties would be changed by injection molding conditions such as melt temperature, mold temperature, injection pressure and holding pressure, etc. In this study, the influences of the injection molding condition on the mechanical properties as tensile strength, hardness of thermoplastic vulcanizates(TPVs), which is one of the TPE, were investigated. By the injection molding experiment, the molding's tensile strength and hardness was influenced on the melt temperature and composition ratio of PP and EPDM. The morphology of moldings were shown by the scanning electron microscope.

• Applied Microscopy
• /
• 제45권4호
• /
• pp.199-202
• /
• 2015

A simple and novel transmission electron microscopy (TEM) sample preparation method for phase change nanowire is investigated. A $Ge_2Sb_2Te_5$ (GST) nanowire TEM sample was meticulously prepared using nanomanipulator and gas injection system in a field emission scanning electron microscopy for efficient and accurate TEM analysis. The process can minimize the damage during the TEM sample preparation of the nanowires, thus enabling the crystallographic analysis of as-grown GST nanowires without unexpected phase transition caused by e-beam heating.

• Transactions on Electrical and Electronic Materials
• /
• 제18권2호
• /
• pp.89-92
• /
• 2017

The performance of three-layered organic light-emitting diodes (OLEDs) was investigated using TPD hole-transport and injection layers, Teflon-AF, and the electron-injection layer of $Li_2CO_3$ and LiF. The OLEDs were manufactured in a structure of TPD/$Alq_3$/LiF, TPD/$Alq_3$/$Li_2CO_3$, and AF/$Alq_3$/LiF using low-molecular organic materials. In three different three-layered OLEDs, it was found that the device with the TPD/$Alq_3$/LiF structure shows higher performance in maximum luminance, and maximum external quantum efficiency compared to those of the device with TPD/$Alq_3$/$Li_2CO_3$ and TPD/$Alq_3$/LiF by 35% and 17%, and 193% and 133%, respectively. It is thought that the combined LiF/Al cathode contributes to a reduced work function and improves an electrical conduction mechanism due to the electron injection rather than the hole transport, which then increases a recombination rate of charge carriers.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제47권1호
• /
• pp.1-5
• /
• 2010

In this paper, we directly compare the program efficiency of conventional channel hot electron (CHE) injection methods and a novel hot electron injection methods using substrate forward biases in our silicon-oxide-nitride-oxide-silicon (SONOS) cell. Compared with conventional CHE injection methods, the proposed injection method showed improved program efficiency including faster program operation at lower bias voltages as well as localized trapping features for multi-bit operation with a threshold voltage difference of 1 V at between the forward and reverse read. This program method is expected to be useful and widely applied for future nano-scale multi-bit SONOS memories.

• ETRI Journal
• /
• 제34권5호
• /
• pp.690-695
• /
• 2012

We investigate the light-emitting performances of blue phosphorescent organic light-emitting diodes (PHOLEDs) with three different electron injection and transport materials, that is, bathocuproine(2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline) (Bphen), 1,3,5-tri(m-pyrid-3-yl-phenyl)benzene (Tm3PyPB), and 2,6-bis(3-(carbazol-9-yl)phenyl)pyridine (26DCzPPy), which are partially doped with cesium metal. We find that the device characteristics are very dependent on the nature of the introduced electron injection layer (EIL) and electron transporting layer (ETL). When the appropriate EIL and ETL are combined, the peak external quantum efficiency and peak power efficiency improve up to 20.7% and 45.6 lm/W, respectively. Moreover, this blue PHOLED even maintains high external quantum efficiency of 19.6% and 16.9% at a luminance of $1,000cd/m^2$ and $10,000cd/m^2$, respectively.

• Journal of the Korean Society for Precision Engineering
• /
• 제22권7호
• /
• pp.177-184
• /
• 2005

Recently, the engineering designer of injection mould has become more and more dependent on the CAE. In the design factors of injection mould, the shrinkage rate should be considered as one of the important performances to produce the reliable products. therefore the shrinkage rate can be mostly calculated by the MoldFlow and Pro-engineering. in the design process. However it is not easy to predict the shrinkage rate of a plastic injection mold in its design process because the analysis can take minutes to hours, the high computational costs of performing the analysis limit their use in design optimization. In this study, the surrogate models, DACE model, based on the Kriging in order to optimize the shrinkage rate of electric microwave oven window is used in lieu of the original models, facilitating design optimization.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.265-268
• /
• 2005

Thermoplastic elastormer (TPE) has many advantages such as high flexibility, high elasticity and high elongation, etc. TPE is easily molded such as plastic materials, therefore, many TPE parts are applied as home appliances and mechanical parts. However, if TPE is once molded, its mechanical properties are changed by injection molding conditions such as melt temperature, mold temperature, injection pressure and holding pressure, etc. In this study, the influences of the injection molding condition on the mechanical properties of thermoplastic vulcanizates(TPVs), which is one of the TPE, were investigated. By the injection molding experiment, as increasing the melt temperature, the tensile strength, shrinkage and hardness decreased. By the scanning electron microscope (SEM) analyzing the TPVs' crystallization, the morphology was affected by the melt temperature.