• 제목/요약/키워드: Electromagnetic-noise filter

검색결과 111건 처리시간 0.03초

3차 PLL System에서의 Flicker Noise 분석 (Flicker Noise Analysis in The Third-order of The PLL System)

  • 김형도;김경복;조형래
    • 한국전자파학회논문지
    • /
    • 제11권5호
    • /
    • pp.707-714
    • /
    • 2000
  • 본 논문에서는 PLL 시스템의 보다 실제적 분석 모델인 3차 시스템을 통하여 저주파 대역에서 문제가 되는 flicker noise가 어떠한 양상을 나타내는가를 알아보려 한다. 3차에서 해석의 복잡성으로 수학적인 분석이 난해하지만 최적화 된 2차 필터를 통한 pseudo-damping factor의 도입으로 3차 시스템에서의 flicker variance의 해석이 용이하도록 시도하였다. 3차에서의 flicker variance의 수식적인 유도를 보이고 이를 2차 시스템에서 발생되는 flicker noise에 대한 variance와 비교하려 한다.

  • PDF

코일성 부하에 의한 전도 노이즈 방지 목적의 전원용 EMI필터 개발 연구 (A Study on the Development of Power-Line EMI Filter for the Prevention of Conduction Noise by Coil Loads.)

  • 김병준;주재훈;김진애;백판근;최중경
    • 한국정보통신학회:학술대회논문집
    • /
    • 한국해양정보통신학회 2009년도 춘계학술대회
    • /
    • pp.175-179
    • /
    • 2009
  • 본 논문에서는 전장용 아날로그 스위치 및 공조기 부하 유닛의 신뢰성 실험 중에서 EMC 스펙에 만족할 수 있도록 하는 필터 설계를 제안한다. EMC 규격에 만족하면서 전자부품들의 상호 간섭과 주변 환경의 영향을 최소화하고 제품의 품질 향상을 위해 전자파 필터를 적용하였다. 본 논문에서는 ISO/JASO 표준규격의 주파수범위인 30MHz ~ 1GHz 대역에서 스펙트럼 분석기와 간이 EMI 챔버를 이용한 시뮬레이션을 통해 특정 주파수 대역의 에너지 분포를 분석하였으며, 최적의 전자파 필터를 구현하기 위해 필터를 구성하는 소자의 용량을 결정하였다. 실제 필터 추가를 통해 노이즈가 감소한 것을 공인인증기관에서 증명하였으며, 전장용 아날로그 스위치 및 공조기 부하 유닛에 적용하여 전자파 간섭을 일으키지 않고 정상적인 동작을 수행하는 것을 확인하였다.

  • PDF

Nano-granular Co-Fe-Al-Q Soft Ferromagnetic Thin Films for RF Electromagnetic-noise Filters

  • Sohn, Jae-Cheon;Byun, Dong-Jin
    • Transactions on Electrical and Electronic Materials
    • /
    • 제7권1호
    • /
    • pp.42-50
    • /
    • 2006
  • Co-Fe-Al-O nano-granular thin films with high electrical resistivity, fabricated by radio frequency magnetron sputtering under an $Ar+O_2$ atmosphere, are found to show good soft magnetic properties in the GHz frequency range. The real part value of the relative permeability is 260 at low frequencies and this value is maintained up to the GHz frequency range. A non-integrated type noise filter on a coplanar waveguide transmission line is demonstrated by using the Co-Fe-Al-O nano-granular thin film with the dimensions of $4\;mm(l){\times}4\;mm(w){\times}0.1\;{\mu}m(t)$. The insertion loss is very low being less than 0.3 dB and this low value is maintained up to 2 GHz. At a ferromagnetic resonance frequency of 3.3 GHz, the degree of noise suppression is measured to be 3 dB. This level of noise attenuation is small for real applications, but there is much room for further improvement by increasing the magnetic volume and integrating the magnetic thin film into the CPW transmission line.

A 0.18-μm CMOS UWB LNA Combined with High-Pass-Filter

  • Kim, Jeong-Yeon;Kim, Chang-Wan
    • Journal of electromagnetic engineering and science
    • /
    • 제9권1호
    • /
    • pp.7-11
    • /
    • 2009
  • An Ultra-WideBand(UWB) Low-Noise Amplifier(LNA) is proposed and is implemented in a $0.18-{\mu}m$ CMOS technology. The proposed UWB LNA provides excellent wideband characteristics by combining a High-Pass Filter (HPF) with a conventional resistive-loaded LNA topology. In the proposed UWB LNA, the bell-shaped gain curve of the overall amplifier is much less dependent on the frequency response of the HPF embedded in the input stage. In addition, the adoption of fewer on-chip inductors in the input matching network permits a lower noise figure and a smaller chip area. Measurement results show a power gain of + 10 dB and an input return loss of more than - 9 dB over 2.7 to 6.2 GHz, a noise figure of 3.1 dB at 3.6 GHz and 7.8 dB at 6.2 GHz, an input PldB of - 12 dBm, and an IIP3 of - 0.2 dBm, while dissipating only 4.6 mA from a 1.8-V supply.

잡음 공분산 추정 방식을 적용한 칼만필터 기반 지면밀착 접근표적 추적기법 (Approaching Target above Ground Tracking Technique Based on Noise Covariance Estimation Method-Kalman Filter)

  • 박영식
    • 한국전자파학회논문지
    • /
    • 제28권10호
    • /
    • pp.810-818
    • /
    • 2017
  • 본 논문에서는 근거리 미사일/로켓 방어시스템의 대응탄용 근접센서에 적용되는 칼만필터 기반 지면밀착 접근표적 추적기법을 제안한다. 탄의 전면에 위치한 근접센서는 지면 클러터를 최소화하기 위한 안테나의 제한된 빔폭으로 인해 위협체가 파편 분산 범위에 들어오는 순간을 감지하기 쉽지 않다. 또한 복잡한 지상 환경에서는 위협체뿐만 아니라, 바위, 나무 등과 같은 클러터 정보를 포함하여 정확한 위협체 감지에 어려움이 따른다. 이를 해결하기 위해 본 연구에서는 칼만필터 기반의 접근표적 추적기법을 제시하고, 추적성능 향상을 위한 잡음 공분산 행렬의 새로운 추정 방식을 적용한다. 이후 제안한 잡음 공분산 행렬을 적용한 칼만필터의 우수한 추적 성능을 발사시험 결과를 통해 제시하여 연구의 타당성을 검증한다.

차량운전자 심전도 신호의 QRS 검출 방법 (Mobile measurement system of ECG signal in vehicle environment)

  • 박재용;오광석;이춘영;이상룡
    • 대한전자공학회:학술대회논문집
    • /
    • 대한전자공학회 2006년도 하계종합학술대회
    • /
    • pp.895-896
    • /
    • 2006
  • This paper proposes a new method to measure the ECG signal from the driver. The ECG signal is often measured in the room. But it is mixed with many kinds of noise when we measure it during the vehicle moving. We classified noise occupied most many parts as the experimental among them. And we designed one suitable filter for each noise. It used ALE(Adaptive Line Enhancement) to remove the noise occurred to electromagnetic wave in vehicle. To remove the noise occurred to steering or vibration of vehicle, we used Wavelet transformation after ALE(preprocessing filter).

  • PDF

Equivalent Parallel Capacitance Cancellation of Common Mode Chokes Using Negative Impedance Converter for Common Mode Noise Reduction

  • Dong, Guangdong;Zhang, Fanghua
    • Journal of Power Electronics
    • /
    • 제19권5호
    • /
    • pp.1326-1335
    • /
    • 2019
  • Common mode (CM) chokes are a crucial part in EMI filters for mitigating the electromagnetic interference (EMI) of switched-mode power supplies (SMPS) and for meeting electromagnetic compatibility standards. However, the parasitic capacitances of a CM choke deteriorate its high frequency filtering performance, which results in increases in the design cycle and cost of EMI filters. Therefore, this paper introduces a negative capacitance generated by a negative impedance converter (NIC) to cancel the influence of equivalent parallel capacitance (EPC). In this paper, based on a CM choke equivalent circuit, the EPCs of CM choke windings are accurately calculated by measuring their impedance. The negative capacitance is designed quantitatively and the EPC cancellation mechanisms are analyzed. The impedance of the CM choke in parallel with negative capacitances is tested and compared with the original CM choke using an impedance analyzer. Moreover, a CL type CM filter is added to a fabricated NIC prototype, and the insertion loss of the prototype is measured to verify the cancellation effect. The prototype is applied to a power converter to test the CM conducted noise. Both small signal and EMI measurement results show that the proposed technique can effectively cancel the EPCs and improve the CM filter's high frequency filtering performance.

DDS Driven PLL 구조 주파수 합성기의 위상 잡음 분석 (Analysis of Phase Noise in Frequency Synthesizer with DDS Driven PLL Architecture)

  • 권건섭;이성재
    • 한국전자파학회논문지
    • /
    • 제19권11호
    • /
    • pp.1272-1280
    • /
    • 2008
  • 본 논문에서는 빠른 천이 시간 및 고해상도 특성을 동시에 만족하기 위해 주로 사용되는 DDS Driven PLL 구조 주파수 합성기의 위상 잡음 분석을 위한 모델링 방안을 제안하였다. 기준 주파수 발진기(reference oscillator) 및 전압 제어 발진기(VCO: Voltage Controlled Oscillator)는 Leeson 모델을 적용하여 측정 데이터를 근사하는 방법을 사용하였고, DDS 칩의 위상 잡음원은 DAC(Digital to Analog Converter) 동작에 근사하여 모델링하였다. PLL의 위상 잡음은 디지털 분주기의 위상 잡음원으로 근사하여 모델링하였으며, 특히 저역 통과 필터(low pass filter)의 각 소자들의 위상 잡음은 전압 제어 발진기의 위상 잡음과 함께 고려하는 방법을 제안하였다. 모델링된 각 잡음 원들을 선형 시스템 영역에서 중첩의 원리를 이용하여 분석함으로써 주파수 합성기 출력의 위상잡음 분포를 예측하였고, 그 결과를 제작된 주파수 합성기의 측정 결과와 비교 평가하였다.

주파수잠금회로(FLL)를 이용한 VCO의 위상잡음 개선 해석 (Analysis of the Phase Noise Improvement of a VCO Using Frequency-Locked Loop)

  • 염경환;이동현
    • 한국전자파학회논문지
    • /
    • 제29권10호
    • /
    • pp.773-782
    • /
    • 2018
  • FLL(Frequency-Locked-Loop: 주파수 잠금회로)은 주파수-검출기(frequency detector)를 사용하여 VCO의 위상잡음을 개선하는 부-궤환(negative feedback) 시스템이다. 본 논문은 FLL에 의한 VCO의 위상잡음의 이론적 분석을 새로이 제시하였다. 분석 결과, VCO의 위상잡음은 FLL 루프-대역폭 내에서는 주파수검출기와 루프-필터로 결정된 위상잡음을 좇아가며, 반면 루프-대역폭 밖에서는 VCO의 위상잡음이 그대로 나타나게 된다. 따라서 이론적 분석 결과를 바탕으로 VCO의 위상잡음을 최소화 하는 FLL을 설계할 수 있게 된다. 또한 실험을 통하여 이론적으로 분석된 위상잡음 결과는 검증하였다.

The Characteristics of Planar EMI Filter with Bi-Ground Layers Considering Impedance Mismatching

  • Wang, Shishang;Song, Zheng;Lou, Qianceng
    • Journal of Power Electronics
    • /
    • 제16권3호
    • /
    • pp.1200-1208
    • /
    • 2016
  • Planar electromagnetic interference (EMI) filter has significant engineering significance to power electronic system integration and miniaturization. However, the value of differential mode capacitance cannot meet the demand of noise suppression because of the size limit of ceramics. In this case, the EMI filter of novel multilayers is recommended to address this issue. A novel integrated structure of EMI filter based on multilayer ceramic is proposed in this study. The inductance and capacitance of the new structure can be designed separately, which is an advantage in manufacturing. Insertion loss is measured more closely to the actual situation in this study, which is different from the condition where source and load impedances are both 50 Ω. In the process of designing a novel EMI filter, noise impedance is considered. Moreover, the prototype is created and applied to a small switching power supply, which verifies the effectiveness of the developed EMI filter.