• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.219-221
• /
• 2005

Sn-9Zn solder balls were bonded to Cu, ENIG (Electroless Nickel/Immersion Gold) and electrolytic Au/Ni pads, and the effect of aging on their joint reliability was investigated. The interfacial products were different from the general reaction layer formed in a Sn-base solder. The intermetallic compounds formed in the solder/Cu joint were $Cu_{5}Zn_{8}$ and $Cu_{6}Sn_{5}$. After aging treatment, voids formed irregularly at the bottom side of the solder because of Sn diffusion into the $Cu_{5}Zn_{8}$ IMC. In the case of the solder/ENIG joint, $AuZn_{3}$ IMCs were formed at the interface. In the case of the Au/Ni/Cu substrate, an $AuZn_{3}$ IMC layer formed at the interface due to the fast reaction between Au and Zn. In addition, the $AuZn_{3}$ IMC layer became detached from the interface after reflow. When the aging time was extended to 100 h, $Ni_{5}Zn_{21}$ IMC was observed on the Ni substrate.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.99-99
• /
• 2018

본 연구는 무전해 니켈 도금 공정에서 고연성을 요구하는 Flexible 기판상에 많이 사용되어지고 있는 무전해 니켈 도금액 평가에 관한 것이다. 무전해 도금을 이용하여 도금된 표면은 다양한 패키징 분야에서의 높은 밀도를 가지는 초소형 소자 등의 실장 표면이나 접합 계면으로 사용되고 있는 등 부품 소재 산업에서의 중요성이 점차 증가되고 있다. 고연성 무전해 Ni-P 도금개발을 통하여 얻고자하는 기술적 과제는 도금층에 높은 연성을 제공하고 안정성이 향상된 무전해 니켈 도금액을 제공하는 것이다.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.597-600
• /
• 2014

In this work, the electromagnetic interference shielding effectiveness (EMI-SE) of carbon nanotube/carbon fiber-reinforced HDPE matrix composites are investigated with various preparation conditions, such as the carbon fiber and carbon nanotube content, the presence of metal additives, as well as mixing speed and time. It was found that the EMI-SE of the composites increased with filler contents and metal additives. These results indicate that the content and length of carbonaceous fillers determine the electric networks in the composites, resulting in the control of the EMI-SE of the composites.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.151-152
• /
• 2011

본 연구에서는 황산니켈, 아세트산니켈, 썰파민산니켈 등 니켈 염 종류에 따른 무전해 니켈 도금피막의 기계적 특성을 평가하고자 하였다. 동일한 두께로 도금피막을 형성하여 내절성 시험결과 황산니켈을 사용한 무전해 니켈 도금피막의 경우 97회, 아세트산니켈을 사용한 경우 259회, 썰파민산 니켈을 사용한 경우 467회의 굴곡 시험 후 도금 피막이 파괴되어 썰파민산니켈이 니켈염으로 사용될 경우 가장 우수한 피막을 나타내었다. 도금피막의 연신울 측정결과 니켈염으로 황산니켈을 사용할 경우 0.28%의 연신율을 나타내었고 아세트산니켈을 사용할 경우 0.32%의 연신율을 나타내었고 썰파민산니켈을 니켈염으로 사용한 결과 0.69%의 높은 연신율을 나타내었으며 개발한 도금액을 PCB 도금을 위한 Cu Pattern에 도금한 경우 Cu line에 선택적으로 도금이 가능하였다.

• Proceedings of the KAIS Fall Conference
• /
• 2004.06a
• /
• pp.65-68
• /
• 2004

순간금형가열방법(MmSH injection process)과 일반적인 방법으로 사출된 ABS 위에 전자파를 차폐하기 위한 무전해 Ni 과 Ag도금을 하였다. 무전해 Ni의 경우, 알칼리성 도금욕일수록 도금속도가 증가하였고 순간금형가열방법으로 사출된 ABS가 일반적인 방법으로 사출된 ABS 보다 밀착력, 광택. 전자파 차폐효율이 다소 높은 값을 가졌으며 pH 8에서 5B의 밀착력, 509의 광택도와 76dB의 전자파 차폐효과를 나타냈다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.5
• /
• pp.433-437
• /
• 2004

The MmSH is a process of injecting ABS to produce innovated physical properties compared to the conventional injection process. Physical properties such as thickness and adhesion strength of Ni plate electrolessly coated on a conventional and a MmSH injected ABS have been studied in the pH range 4~8. Thickness of the plate on the MmSH and the conventionally injected ABS appeared to be directly proportional to pH. The ABS processed by the conventional injection showed adhesion strength corresponded to ASTM 4B above pH 5. On the other hand, the ABS processed by the MmSH injection showed a superior adhesion strength corresponded to ASTM 5B above pH 6. It was calculated the shielding effectiveness of above 50 dB in all conditions.

• 전자공학회논문지 IE
• /
• v.43 no.4
• /
• pp.122-127
• /
• 2006

A series of conductive filler were prepared with electroless plating method. Base conductive materials of the filler were nickel and copper. The cores were prepared with Nylon 6 and rayon in different aspect ratio. Also, various complexes were made with ABS resin and conductive filler with different filler feed ratio. The conductivity of the filler was measured with conductivity analyzer and the size distributions of fillers was measured with laser particle size analyzer. Electromagnetic wave shielding efficiency of each complex film was measured with flange circular coaxial transmission line sample holder within the 1MHz$\sim$1GHz bandwidth range. From this study, the conductivity of filers surpass that of other carbon films. It is available that the filler made of fibrous materials can be applied in plastic molding industry of electric appliances as a EMI filler.

• Journal of Power System Engineering
• /
• v.5 no.2
• /
• pp.71-78
• /
• 2001

Using sodium hypophosphite as reducing agent, bath composition and plating condition of electroless copper plating on plating rate have been studied. The followings were determined as optimum, bath composition; $CuSO_4\;0.025M,\;NiSO_4\;0.002M,\;NaH_2PO_2\;0.4M$, sodium citrate 0.06M, $H_3BO_3$ 0.6M, thiourea or 2-MBT $0.2mg/{\ell}$, and operation conditions; pH $9{\sim}10$ at bath temperature rage of $60{\sim}70^{\circ}C$. A small amount of nickel ion($Ni^{2+}/Cu^{2+}$=0.002/0.025) to the hypophosphite reduced solution promotes autocatalysis and continuous plating. An additive such as thiourea or 2-MBT of a small amount($0.2mg/{\ell}$) can be used to stabilize the solution without changing plating rate much. The attivation energy between $20^{\circ}C\;and\;70^{\circ}C$ were calculated to be 11.3kcal/mol for deposition weight. Plating reaction had been ceased by the adjustment of pH above 13, temperature higher than $90^{\circ}C\;and\;under\;20^{\circ}C$. Deposited surface became worse in the case of increment of bath temperature above $80^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.5 no.7
• /
• pp.794-801
• /
• 1995

To connect the driver IC and Al coated glass, a method has been developed to plate electrolessly Ni on Al/PR system. It Is necessary to pretreat Al to remove oxide film before plating. In order to find pretreatment process which does not damage photoresist or glass, alkaline and fluoride zincate process have been investigated. Because photoresist and aluminum thin film can easily dissolve in alkaline solution, it is considered that the fluoride zincate process was a suitable one. After immersion in the zincate solution containing 1.5 g/$\ell$ ammonium bifluoride and 100 g/$\ell$ zinc sulfate, electroless nickel plating could be performed. The additive in the zincate solution and thiourea in the plating solution increased smoothness of the plated surface. Acld dip could improve the uniformit of the surface.

• Composites Research
• /
• v.21 no.2
• /
• pp.31-35
• /
• 2008

In order to design light weight and high efficient electromagnetic wave absorbing materials, hollow magnetic particles have been introduced in this study. The electroless plating method has been utilized to coat Ni and Fe on the substrates of synthesized polystyrene particles of submicron size. Removing polystyrene particles by heat treatment resulted in hollow structures. Observation by SEM, TEM and EDS confirmed the surface morphology and coating thickness of Ni and Fe. Polymeric composites containing hollow particles were tested in order to compare the electromagnetic properties between Ni coated and Fe costed particles. The composite of 30 wt% Fe hollow particles showed the higher complex permeability than Ni hollow particles or the conventional barium ferrite particles.