• Resources Recycling
• /
• v.21 no.2
• /
• pp.41-46
• /
• 2012

An investigation on the recovery of nickel from spent electroless plating solutions has been performed using the electrowinning method. For this aim, nickel in spent electroless plating solutions was separated as nickel hydroxide through the addition of caustic soda. Nickel hydroxide was completely dissolved with sulfuric acid and an electrolysis was performed for electrowinning of nickel from nickel solutions. As a result, it was found that more than 99% of nickel in spent electroless plating solutions could be precipitated as nickel hydroxide above pH 10 with the addition of caustic soda. As far as the current efficiency in electrowinning of nickel was concerned, it was decreased with increase in the current density.

• Resources Recycling
• /
• v.21 no.6
• /
• pp.39-44
• /
• 2012

An attempt to recover copper from electroless plating wastewater has been made through evaporation followed by the electrowinning method. From the determination of each element in electroless plating wastewater, the content of Cu was found to be 582 mg/l and small amount of Fe was also contained in it. Moreover, the content of COD and TOC which was resulted from the addition of Rochell salt was found to be 9,560 and 13,100 mg/l, respectively. The content of formic acid generated by the oxidation of formaldehyde was determined to be 7.73 %. As a result, current efficiency was decreased with increase in current density and therefore current density less than $40mA/cm^2$ should be maintained to obtain current efficiency more than 80 %. The content of Fe in Cu obtained by electrowinning was found to be 0.021 and 0.01 % at the concentration of sulfuric acid of 2 and 10 vol%, respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.4
• /
• pp.204-209
• /
• 2015

The effluent limit of nickel from electroplating wastewater has been strengthened from 5 mg/L to 3 mg/L from 2014. However, currently applied treatment process for nickel plating wastewater is unable to meet the effluent limit, most of the treatment concept conducted by treatment plant is dilution with other metal bearing wastewater. This can cause very significant impact to the environment of nickel contamination. With this connection, the feasibility test has been conducted with the use of electrolysis by using sacrificial electrodes. Experiments were conducted in synthetic and electroless nickel plating wastewater. Optimal condition of current density, pH were derived from the synthetic wastewater. It was found that the removal efficiency of nickel exceeded 94% at the operation condition of at pH 9 and the current density of $1{\sim}2mA/cm^2$. At this conditions, the iron sludge was generated very low amount. However, it was unsuccessful to meet the effluent limit by applying these treatment conditions to the real electroplating wastewater. This can be explained due to the matrix effect of other metals and anions contained real electroplating wastewater. From the result of further study, the optimal conditions for the real wastewater treatment were found out to be at pH 9, current density $6{\sim}7mA/cm^2$, for 5 minutes of operating time. At these conditions, 88% removal of nickel was achieved, which results the residual nickel concentration was below 3 mg/L.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1338-1347
• /
• 2018

In this study, Ti-mesh based electrodes were fabricated for the application of anode to the electrolysis process for wastewater treatment using Pd electroless plating method. The removal performance of the prepared Pd / Ti-mesh electrode was evaluated as representative dye RO16, and the durability and performance were maximized by varying the electrode manufacturing conditions. As a result, it was confirmed that the coating condition had no significant effect on the performance, and that the heat treatment process greatly affected the performance and the durability was improved. In addition, we tried to maximize performance and durability by complexing Ir, Ru, and Ta. However, as the thickness of the layer increased due to the limitation of the coating method, the resistance increased and the performance decreased accordingly.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.1
• /
• pp.1-7
• /
• 2016

In order to treat electrolysis nickel plating pickling wastewater to meet the effluent limit less than 3.0 mg/L, the electrolysis process by using soluble and insoluble electrode were studied. Electrolysis using soluble electrodes has a characteristic of easy elution from the electrode which the insoluble electrodes close not release metal from the electrode. For these reasons, there exist different characteristics in nickel removal efficiency, purity of nickel sludge. With this connection, the feasibility test were concluded to develop optimal conditions for the treatment of pickling wastewater electrolysis by using soluble electrodes, insoluble electrodes. Optimal condition of current density, pH were derived from the pickling wastewater using insoluble electrodes. It was concluded the highest removal efficiency of nickel at the operation condition of at pH 9, current density of $15mA/cm^2$. At these conditions, 95.3% purity of nickel sludge was achieved, iron content was 2.9%. Optimal condition when using soluble electrodes was derived current density of $10mA/cm^2$, pH 9. Purity of nickel sludge was 77.3%, iron content was 21.0%. 50.7% and 24.2% of operating cost can be saved by the use of soluble electrodes and the use of insoluble electrodes, respectively.

• Membrane Journal
• /
• v.13 no.1
• /
• pp.9-19
• /
• 2003

Membrane process was investigated to recover process water and valuable gold from washing water of electroless PCB plating processes. The filtration experiments were carried out using not only a RO membrane test cell to determine suitable membrane for washing water but also spiral wound membrane modules of nanofiltration and reverse osmosis for scale-up. At first, RO-TL(tap water, low pressure), RO-BL(brackish water, low pressure) and RO-normal(for water purifier) sheet membranes made by Saehan Co. were tested, and the performance of RO-TL membrane showed most suitable f3r recovery of soft etching, catalyst and Ni washing waters. As a result of RO test cell, the experiments for scale-up were carried out using RO-TL modules far water purifier at 7bar and $25^{\circ}C $The permeate flux fur Au washing water was about 30 LMH, but Au rejection was less than 80%. The permeate fluxes for Pd, Ni and soft etching washing water were about 22, 17 and 10 LMH, respectively. The Pd, Ni and Cu rejections showed more than 85, 97 and 98% respectively. The nanofiltration module for water purifier was introduced to recover Au selectively from Au, Ni and Cu ions in Au washing water. Most of Ni and Cu ions in the feed washing water were removed, and only Au ion was existed 81.9% in the permeate. Furthermore, Au ion in the permeate was concentrated and recovered by RO-TL membrane module. Finally, Au was also able to recover effectively by using 4 inch diameter spiral wound modules of NF and RO-TL membranes, in series.

• Nano
• /
• v.13 no.11
• /
• pp.1850134.1-1850134.10
• /
• 2018

Increasing active sites and enhancing electric conductivity are critical factors to improve sensing performance toward phenol. Herein, Ni nanoparticle was successfully anchored on acidified multiwalled carbon nanotube (a-MWCNT) surface by electroless plating technique to avoid Ni nanoparticle agglomeration and guarantee high conductivity. The crystal structure, phase composition and surface morphology were characterized by XRD, SEM and TEM measurement. The as-prepared Ni/a-MWCNT nanohybrid was immobilized onto glassy carbon electrode (GCE) surface for constructing phenol sensor. The phenol sensing performance indicated that Ni/a-MWCNT/GCE exhibited an amazing detection performance with rapid response time of 4 s, a relatively wide detection range from 0.01 mM to 0.48 mM, a detection limit of $7.07{\mu}M$ and high sensitivity of $566.2{\mu}A\;mM^{-1}\;cm^{-2}$. The superior selectivity, reproducibility, stability and applicability in real sample of Ni/a-MWCNT/GCE endowed it with potential application in discharged wastewater.

• Resources Recycling
• /
• v.30 no.3
• /
• pp.47-54
• /
• 2021

Palladium present in colloidal-type plated spent catalyst solution that is used in electroless plating process has not been recovered but discharged as wastewater so far. Recyclig of paladium in colloidal-type plated spent catalyst solution is achieved with this study. This study presents the estimation of resource consumption and GHG emissions during the recycling and disposal of palladium in the plated spent catalyst solution using life cycle assessment. The reduction of resources and GHG are also estimated. Based on the palladium amount of 1 kg during disposal, the GHG emission amount was estimated to be 9.67E+03 kgCO₂eq., and the amount of resource consumption was 3.94E+01 kgSb-eq. However, GHG emission was 1.96E+03 kgCO₂eq., and the amount of resource consumption was 1.54E+01 kgSb-eq. during recycling. Considering the major substances affecting GHG emissions and amount of resource consumption, CO₂ was found to significantly affect GHG emissions, accounting for 91.42% in disposal and 98.37% in recycling. The major substance affecting the amount of resource consumption was hard coal, which accounted for 40.63% in disposal and 60.73% in recycling. Upon recycling 1 kg palladium, 8,967.17 kgCO₂eq. of greenhouse gas emission was reduced, while the resource consumption was reduced to 10.10 kg Sb-eq. In addition, the direct palladium resource reduction rate due to palladium recycling was 50%.