• Particle and aerosol research
• /
• v.10 no.4
• /
• pp.177-182
• /
• 2014

In this study, nickel-coated aluminum (Ni/Al) powders were synthesized for the utilization of energetic applications. Oxide materials present at the surface of Al powders of $45{\mu}m$ in averaged size were removed by using sodium hydroxide(NaOH) solution which is used for controlling pH. Nickel material is coated into the surface of oxide-removed Al powders by electroless-plating process. The microstructure of fabricated Ni/Al powders shows that nickel layers with a few hundreds nm were very homogeneously formed onto the surface of Al powders. The oxidation behavior of Ni/Al exihibit somewhat faster oxidation rate than that of pure Al with surface oxidation. Also, the higher exothermic reaction was observed from the Ni/Al powders. From the result of this, nickel coating is very promising method to obtain highly reactive and safe Al powders for energetic applications.

• Journal of the Korean institute of surface engineering
• /
• v.19 no.3
• /
• pp.83-91
• /
• 1986

Codeposited of boron nitride(BN) particle dispersed into electroless nickel-phosphours (Ni-P) and nickel-boron(Ni-B) platings were studied for the purpose of developing the wear resistance and lubricity. BN can be codeposited from electroless nickel plating bath with $NaH_2PO_2$ and $NaBH_4$ as the reducing agents. Most dispersolids were distributed uniformly in the Ni-P and Ni-B matrix. Abrasion loss decreased with increasing amount of codeposits and reached a constant value 2.4 percent by volume percent of BN particle. The wear resistance and the friction coefficient of the heat treated BN composite coatings were improved about three times than that of as-coatings. The BN composite coatings were more wear resistance than hard chromium. Ni-B-BN composite coatings showed lower wear resistance and friction coefficient than Ni-P-BN. The BN content of the deposite was found to be 2.4 v/o for these optium conditions.

• Korean Journal of Materials Research
• /
• v.15 no.9
• /
• pp.577-584
• /
• 2005

Thin Ni-B layer, $1{\mu}m$ thick, was electrolessly deposited on Cu electrode fabricated by electro-deposition. The purpose of the layer is to encapsulate Cu electrodes for preventing Cu oxidation and to serve as a diffusion barrier. The layers were annealed at $580^{\circ}C$ with and without pre-annealing at $300^{\circ}C$ for . 30minutes. In the layer with pre-annealing, the amount of Cu diffusion was lower about 5 times than the layer without pre-annealing. The difference in Cu concentration may be attributed to $Ni_3B$ formation prior to Cu diffusion. However, the difference in Cu concentration decreased during the annealing time of 5 h due to the grain growth of Ni.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.1
• /
• pp.49-54
• /
• 2023

Recently, System in Packaging(SIP) technology needs to meet high frequency (5G and more) communication technology and fine pitch surface treatment. The conventional Electroless Ni/Immersion Au plating(ENIG) is not suitable for high frequency range because of magnetic properties are increasing the transmission loss. Without nickel plating layer, the pattern and pad reliability level must be meet the condition. In this review paper, we investigated research trends on Ni-less surface treatment technology for high-frequency communication and frequency characteristics according to materials.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.2 s.35
• /
• pp.95-103
• /
• 2005

The interfacial reaction between 42Sn-58Bi solder (in wt.$\%$ unless specified otherwise) and electroless Ni-P/immersion Au has been investigated before and after thermal aging, with a focus on formation and growth of an intermetallic compound (IMC) layer, consumption of under bump metallurgy (UBM), and bump shear strength. The immersion Au layer with thicknesses of 0 (bare Ni), 0.1, and $1{\mu}m$ was plated on the $5{\mu}m$ thick electroless Ni-P ($14{\~}15 at.\%$P) layer. Then, the 42Sn-58Bi solder balls were fabricated on three different UBM structures by screen-printing and pre-reflow. The $Ni_3Sn_4$ layer (IMC1) was formed at the joint interface after pre-reflow for all the three UBM structures. On aging at $125^{\circ}C$, a quaternary phase (IMC2) was observed above the $Ni_3Sn_4$ layer in the Au-containing UBM structures, which was identified as $Sn_{77}Ni{15}Bi_6Au_2$ (in at.$\%$). The thick $Sn_{77}Ni{15}Bi_6Au_2$ layer deteriorated the integrity of the solder joint and the shear strength of the solder bump was decreased by about $40\%$ compared with non-aged joints.

• Corrosion Science and Technology
• /
• v.4 no.6
• /
• pp.222-225
• /
• 2005

The adhesion strength of metal plating on PC was studied. In this study, surface was treated by chemical agents or DBD(dielectric barrier discharge) plasma to imporve the adhesion. The surface roughness, contact angle, gloss of plating and adhesive strength were measured. Adhesion strengths of Ni plating on prepared PC by NaOH and KOH solution were $12.3kgf/cm^2$ and $7.5kgf/cm^2$, respectively. The highest adhesion strength was obtained in the plasma treated one, $27.8kgf/cm^2$.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1419-1421
• /
• 1995

Nickel micro-structures are fabricated by electroless plating which shows better uniformity. Positive resist AZ4562 of 7 um thickness is patterned with minimum width of 2 um on poly-silicon as for sacrificial layer. The growth rate of Ni electroless plating is 10um/h both for the seed layer of Pt and TiW. TiW is found to be more practical than Pt, since it is very difficult to remove Pt with negligible damage to Ni structures.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.4
• /
• pp.1-5
• /
• 2002

A 110 m diameter aspheric metal secondary mirror for a test model of an earth observation satellite camera was fsbricated by ultra-precision single point diamond turning (SPDT). Aluminum alloy for mirror substrates is known to be easily machinable, but not polishable due to its ductility. A harder material, Ni, is usually electrolessly coated on an A1 substrate to increase the surface hardness for optical polishing. Aspheric metal secondary mirror without a conventional polishing process, the surface roughness of Ra=10nm, and the form error of Ra=λ/12(λ=632.8nm) has been required. The purpose of this research is to find the optimum machining conditions for reflector cutting of electroless-Ni coated A1 alloy and apply the SPDT technique to the manufacturing of ultra precision optical components of metal aspheric reflector.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.3
• /
• pp.215-224
• /
• 2001

Cotton was etched in 15% NaOH solution at $90^{\circ}C$ for 15 min in order to give good wettability. Then it was catalyzed and accelerated by using $PdC1_2$-$SnCl_2$ solution and 10% $_2$$SO_4$, respectively. Uniform deposits on cotton were obtained when it was electroless copper deposited in pH 10.5 solution at 3$0^{\circ}C$ and Ni-Fe-P deposited in solutions of pH 11 at$ 75^{\circ}C$. The latter deposit has a chemical composition similar to that of permalloy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1125-1128
• /
• 2001

A 110mm diameter aspheric metal secondary mirror for a test model of an earth observation satellite camera was fabricated by ultra-precision single point diamond turning(SPDT). Aluminum alloy for mirror substrates is known to be easily machinable, but not polishable due to its ductility. A harder material, Ni, is usually electrolessly coated on an Al substrate to increase the surface hardness for optical polishing. Aspheric metal secondary mirror without a conventional polishing process, the surface roughness of Ra=10nm, and the form error of Ra=λ/12(λ=632nm) has been required. The purpose of this research is to find the optimum machining conditions for reflector cutting of electroless-Ni coated Al alloy and apply the SPDT technique to the manufacturing of ultra precision optical components of metal aspheric reflector.