• Transactions on Electrical and Electronic Materials
• /
• v.15 no.2
• /
• pp.77-80
• /
• 2014

The effect of reactive diluents on the ac electrical treeing in epoxy/nanosilicate systems was studied, in a needle-plate electrode geometry. Diglycidyl ether of bisphenol A (DGEBA) type epoxy was used as a base resin, and layered silicate was used as a nano-sized filler. Polyglycol (PG) or 1,4-butanediol diglycidyl ether (BDGE) was introduced as a reactive diluent to the DGEBA/nanosilicate system, in order to decrease the viscosity of the nanocomposite system. PG acted as a flexibilizer, and BDGE acted as a chain extender, after the curing reaction. To measure the treeing propagation rate, a constant alternating current (ac) of 10 kV/4.2 mm (60 Hz) was applied to the specimen, in a needle-plate electrode arrangement, at $30^{\circ}C$ of insulating oil bath. When 10 kV/4.2 mm (60 Hz) was applied, the treeing propagate rate in the DGEBA system was $1.10{\times}10^{-3}$ mm/min, and that in the DGEBA/PG system was $1.05{\times}10^{-3}$ mm/min. As 1.5 wt% of nanosilicate was added to the DGEGA/PG system, the propagation rate was $0.33{\times}10^{-3}$ mm/min. This meant that the nano-sized layered silicates would act as good barriers to treeing propagation. The effect of chlorine content was also studied, and it was found that chlorine had a bad effect on the electrical insulation property of the epoxy system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.444-449
• /
• 1998

A modal transducer in two-dimensional structure can be implemented by varying the distributed transducer's gain spatially. In this paper, a method based on finite element method is developed for optimizing spatial gain distribution of PVDF transducer to create the modal transducer for specific modes. Using this concept, one can design the modal transducer in two-dimensional structure having arbitrary geometry and boundary conditions. As a practical means for implementing this continuous gain distribution without repoling die PVDF film, the gain distribution is approximated by optimizing gain-weights of interface circuit. The whole spatial area of the PVDF film is divided into several electrode segments and the signals from each segment are properly weighted and summed by interface circuit. This corresponds to the approximation of a continuous function using discrete values. The electrode partition is optimized using the genetic algorithm. Gain-weights are optimized using the simplex search method. A modal sensor for first to fourth modes of aluminum plate is designed using PVDF film with gain-weighted interface circuit. Various lamination angles of PVDF film are taken into consideration to utilize the anisotropy of the PVDF film. Performance of the optimized' PVDF sensor is demonstrated by numerical simulations..

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.31-31
• /
• 2009

최근 전세계적으로 유가상승 및 환경에 대한 관심이 증대되면서 자동차 업계에서는 차량 경량화를 통한 연비향상에 대한 연구가 활발히 진행되고 있다. 대표적인 기술개발 사례로서 초경량 철강 차체의 개발을 들 수 있다. 이는 고장력강을 적용함으로써 강성을 증대시킴과 동시에 두께감소에 의한 경량화를 이루고자 추진되고 있다. 하지만 고장력강은 자체의 높은 강성을 지니고 있는 반면, 일반 강종에 비해서 스프링백이 크고 용접성도 많이 떨어지는 제약을 안고 있다. 아크 용접법 중 하나인 AC pulse MIG 용접은 DCEP (direct current electrode positive) 와 DCEN (direct current electrode positive) 구간이 주기적으로 반복하는 용접법으로 스패터 발생이 거의 없으며 특히 갭 접합성이 우수하여 자동차 차체 조립공정에 적용되고 있다. 본 연구에서는 자동차 차체용 AHSS 소재의 겹치기 용접 실험을 통해 실제 생산라인에서 용접 이음부에 발생되는 갭에 대해 강건한 용접 공정 조건을 제시하였다. 먼저 고속카메라 촬영을 통해 AC pulse MIG 용접에서 EN ratio 변화에 따른 와이어 용융현상을 분석 하였으며 단면마크로, 인장시험, 인장 파단면 분석을 통해 겹치기 용접에서 0~2mm 사이의 갭 발생에 강건한 용접 조선을 제시하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.4
• /
• pp.223-231
• /
• 2019

A continuum-based design sensitivity analysis(DSA) method is developed for electrostatic problems. To consider high order objective functions, we use 9-node finite element basis functions for analysis and DSA methods. As the design variables are parameterized with B-spline functions, smooth boundary variations are naturally obtained. To solve mesh entanglement problems during the optimization process, a mesh regularization scheme is employed. By minimizing the Dirichlet energy functional, mesh uniformity can be automatically achieved. In numerical examples for maximizing dielectrophoresis forces, the numerical results are compared with well-known electrode geometries and the obtained characteristics are discussed.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.2
• /
• pp.85-88
• /
• 2012

Studies on the effects of layered silicate content on the AC electrical treeing and breakdown behaviors of epoxy/layered silicate nanocomposites were carried out in needle-plate electrode geometry. Wide-angle X-ray diffraction (WAXD) analysis and transmission electron microscopy (TEM) observation showed that 1 wt% of the multilayered silicate was fully exfoliated into nano-sized monolayers in the epoxy matrix however, over 3 wt% of the silicate was in an intercalated state. When 1 wt% layered silicates were incorporated, an electrical tree was initiated in 439 min and propagated at a speed of 2.3 ${\mu}m$/min after applying 781.4 kV/mm, representing a decreased in starting initiation time by a factor of 11.0 and increase in propagation speed by a factor 8.2 in comparison with neat epoxy resin. These values were in great decline after the layered silicate content was increased to 3wt% which implies that the exfoliated silicate blocked the tree initiation and propagation processes effectively. However the effect was largely decreased in the intercalated state.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.209-209
• /
• 2012

전자의 에너지를 측정하기 위한 분석장치는 원자핵물리뿐만 아니라 화학과 생물학 등 다양한 분야에 걸쳐 매우 유용하게 사용될 수가 있다. 특히 최근에 극고속 과학과 관련해서 매우 짧은 펄스인 아토초 펄스의 발생에 대한 특성평가를 위해 매우 중요한 장치로 사용되고 있다. 그 중 VMI (Velocity Map Imaging) 방법은 TOF (Time of Flight) 방법과 유사하지만, CCD 카메라를 추가로 사용하여 이차원 이미지를 얻음으로써 전자의 운동에너지 및 각도 분포에 대한 정보를 얻을 수 있고 또한 전극에 인가되는 전압은 TOF와 달리 매우 높다. 이번 개발에서는 기존의 전극 렌즈의 geometry와 비교해서 VMI Spectrometer 전극 렌즈의 수를 늘려 multi-electrode concept을 도입함으로써 높은 운동에너지(~1000 eV)를 가진 전자들을 MCP detector상에서 imaging 하는데 있어 높은 공간 분해능(resolution)을 갖도록 설계하고, 또한 높은 사양의 MCP detector 및 CCD 카메라를 이용하여 시간 분해능을 높임으로써 아토초 펄스를 이용한 극고속 실험에 이용 가능하도록 제작하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.378-379
• /
• 2009

High intensity metal halide discharge lamp performance, specifically the generated luminous flux and light color content, depends critically on the arc tube design. Factors influencing the design and consequent lamp efficacy include : lamp size, geometry, arc tube composition, fill chemistry, electrode design and excitation modes. Shaping of Polycrystalline Alumina(PCA) can be realized by conventional ceramic processes. Several processes are applied nowadays. Well-known in the ceramic high pressure field for decades are the pressing and the extrusion method. Newly developed slurry and precious forming technologies give the one-body seamless tubes, which improve thickness uniformity and lighting performance. Now, we reported some optical properties with different arc tube structures of ceramic metal halide lamps.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.9
• /
• pp.1085-1094
• /
• 1992

A variable-spacing cesium thermionic energy conversion test station is designed and fabricated for the study of power generation. The diode is in the form of a guard-ringed plane-parallel geometry in which a polycrystalline rhenium emitter of 2 cmS02T area faces a radiation-cooled polycrystalline rhenium collector of 1.9 cmS02T area. The emission of plasma from heated refractory electrode metal is the driving reaction in the direct conversion of heat to electricity by thermionic energy conversion. The plasma is produced from electrons and positive ions formed simultaneously by thermionic emission and surface ionization of cesium atoms incident on the hot emitter from the cesium vapor in the diode. And high plasma density causes plasma multiplication within the gap due to volume ionization that results in high power output. The variation of the saturation current of a Knudsen converter is investigated at an emitter-collector gap of 0.1 mm and an emitter temperatures. A maximum power output of 13.47 watta/cmS02T is observed at a collector temperature of 963 K and a cesium reservoir temperature of 603 K.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1740-1745
• /
• 2004

A simplified resistor network model for electrical and mass transport in anode-supported planar solid oxide fuel cell (SOFC) was constructed in order to investigate the effect of interconnect rib geometry on the cell performance. For accurate potential calculation, activation and concentration over-potentials at the electrode/electrolyte interfaces were fully considered in this calculation. When contact resistance was not considered, the optimum interconnect rib length were calculated to be $0.1{\sim}0.2$ mm for 2 mm half unit cell for given operation conditions and properties. However, with realistic contact resistance, the interconnect rib length should be increased to provide larger contact area and thus to obtain better performance.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.1
• /
• pp.43-48
• /
• 2003

점용접은 자동차를 제작하는데 사용하는 가장 유용한 용접법이다. 그러나 산업현장에서 직면하고 있는 가장 큰 문제점 중의 하나는 점용접의 용접성에 관한 문제이다. 본 연구에서는 강판의 두께가 1.6mm인 경우와 1.2mm인 경우에 대해 2점 점용접을 실시하여 인장강도를 증가시키고 용접의 흔적을 남기지 않게 하기 위한 조건을 찾는 것을 목적으로 하였다. 용접성에 영향을 미치는 많은 요소들이 있다. 그중에서 용접전극의 형상이 인장강도를 증가시키는 요소로 집중을 하면서 연구를 수행하여 다음과 같은 결과를 얻었다. 인장강도는 용접전극의 형상 및 팁직경 거리와 전류가 클수록 증가하였다. 시행 착오법을 통해 최적용접조건을 찾았고 그에 따른 최적전류인 9,000A와 전극의 형상 RF형을 찾았다. 경도시험결과는 인장력이 시험편에 작용할 때 열 영향부인 HAZ부에서 왜 파괴가 일어나는지를 설명해 주었다.