• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.1
• /
• pp.25-29
• /
• 2020

This study demonstrates direct-patternable amorphous TiO_x resistive switching (RS) device and the fabrication method using photochemical metal-organic deposition (PMOD). For making photosensitive stock solutions, Ti(IV) 2-ethylhexanoate was used as starting precursor. Photochemical reaction by UV exposure was observed and analyzed by Fourier transform infrared spectroscopy and the reaction was completed within 10 minutes. Uniformly formed 20 nm thick amorphous TiO_x film was confirmed by atomic force microscopy. Amorphous TiO_x RS device, formed as 6 × 6 ㎛ square on 4 ㎛ width electrode, showed forming-less RS behavior in ±4 V and on/off ratio ≈ 20 at 0.1 V. This result shows PMOD process could be applied for low temperature processed ReRAM device and/or low cost, flexible memory device.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.157-162
• /
• 2014

In this research, we investigate electrical performance and electrochemical properties of carbon supported Pt (Pt/C) that is synthesized by polyol method. With the Polyol_Pt/C that is adopted for oxygen reduction reaction (ORR) as cathode of proton exchange membrane fuel cells (PEMFCs), their catalytic activity and ORR performance and electrical performance are estimated and compared with commercial Pt/C(Johnson Mattey) catalyst. Their electrochemically active surface (EAS) area are measured by cyclic voltammetry (CV), respectively. On the other hand, regarding ORR activity and electrical performance of the catalysts, (i) linear sweeping voltammetry by rotating disk electrode and (ii) PEMFC single cell tests are used. The CV measurement demonstrate EAS of Polyol_Pt/C is compared with commercial JM_Pt/C. In case of Polyol_Pt/C, its half-wave potential, kinetic current density are excellent. Based on data obtained by half-cell test, when PEMFC single cell tests are carried out, current density measured at 0.6V and maximum power density of the PEMFC single cell employing Polyol_Pt/C are better than those employing commercial Pt/C. Conclusively, Polyol_Pt/C synthesized by modified polyol process shows better ORR catalytic activity and PEMFC performance than other catalysts.

• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.73-79
• /
• 1999

The superstructured $Li_{4/3}Ti_{5/3}O_4$ was prepared by sol-gel process using a mixed solution of lithium acetate (LA) and titanium n-butoxide (TNB). The gel phase was obtained by adding ammonia water ($NH_4OH/TNB$ mole ratio of 0.35) and water ($H_2O/TNH$ mole ratio of 3.5) into the clear sol that was prepared after mixing TNB/LA mole ratio of 5/4 with AA/TNB mole raio of 0.125. It was found that the most suitable $Li_{4/3}Ti_{5/3}O_4$ was obtained by heat treatment of xerogel at $600^{\circ}C$ for 30 hrs. The synthesized $Li_{4/3}Ti_{5/3}O_4$ showed an initial discharge capacity of 174 mAh/g and the capacity loss of about 27.3% during 25 cycles in Li/1M $LiClO_4(in\;PC)/Li_{4/3}Ti_{5/3}O_4$ at current density of $0.15mA/cm^2$ and the voltage range of 0.5~3.0 V.

• Resources Recycling
• /
• v.17 no.2
• /
• pp.36-45
• /
• 2008

Pickling of oxidized 304 stainless steel has been investigated using rotating disk electrode in waste acid solutions generated from the etching process of silicon wafer in order to recycle them. The waste acid solution contained acetic, nitric, hydrofluoric acids, and silicon of $19.6g/L^{-1}$. Electrochemical behavior during the pickling was distinctively different between the original and silicon-removed acid solutions. Open circuit potential was continuously changed in the original solution, while it was discontinuously changed and fluctuated in the silicon-removed solution. Fast and abrupt removal of surface oxide layer with severe pitting was observed in the silicon-removed solution. It was found that solution temperature had the most influential effect on glossiness. Surface glossiness after pickling was decreased with solution temperature. At the same condition, the glossiness was higher in the original solution than in the silicon-removed solution.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.2
• /
• pp.125-133
• /
• 2017

KAERI is conducting research on spent cladding hulls and additive metals to generate a solidification host matrix for the noble metal fission product waste in anode sludge from the electro-refining process to minimize the volume of waste that needs to be disposed of. In this study, alloy compositions Zr-17Cr, Zr-22Cr, and Zr-27Cr were prepared with or without eight noble metals representing fuel waste using induction melting. The microstructures of the resulting alloys were characterized and electrochemical corrosion tests were conducted to evaluate their corrosion characteristics. All the compositions had better corrosion characteristics than other Zr-based alloys that were evaluated for comparison. Analysis of the leach solution after the corrosion test of the Zr-22Cr-8NM specimen indicated that the noble metals were not leached during corrosion under 500 mV imposed voltage, which simulates a highly oxidizing disposal environment. The results of this study confirm that Zr-Cr based compositions will likely serve as chemically stable waste forms.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.4
• /
• pp.237-242
• /
• 2009

In the pyroprocessing of spent nuclear fuels, fuel materials are recovered by electrochemical reactions on the surface of electrodes as well as stirring the electrolyte in electrolytic cells such as electrorefiner, electroreducer and electrowinner. The system with this equipment should first be scaled-up in order to commercialize the pyroprocessing. So in this study, the scale-up for those electrolytic cells was studied to design a large-scale system which can be employed in a commercial process in the future. Basically the dimensions of both electrolytic cells and electrodes should be enlarged on the basis of the geometrical similarity. Then the criterion of constant power input per unit volume, characterizing the fluid behavior in the cells, was introduced in this study and a calculation process based on trial-and-error methode was derived, which makes it possible to seek a proper speed of agitation in the electrolytic cells. Consequently examples of scale-up for an arbitrary small scale system were shown when the criterion of constant power input per unit volume and another criterion of constant impeller tip speed were respectively applied.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.43-48
• /
• 2011

The maximum current density of copper electrorefining is 350 A/$m^2$ and the higher current density is required to promote the copper productivity. The 1000 A/$m^2$ high current density is possible when rotating disc electrode is employed to reduce diffusion thickness. The copper electroplating with 1000 A/$m^2$ is possible at 400 rpm. Thiourea and glue were used to improve the electrodeposition behaviors during copper electrorefining process. Potentiodynamic polarization tests were conducted to investigate the effects of additives on copper electrodeposition. Galvanostatic tests were also conducted at 1000 A/$m^2$. Copper were electroplated on cylindrical rotating electrodes to give the uniform flow on the electrode surface. The lowest surface roughness was obtained when 16 ppm thiourea was added to the electrolytes. The surface roughness was increased with glue concentration. The surface hardness was not influenced by addition of glue. The copper nuclei were getting smaller with thiourea concentration, however there is no glue effects on copper nucleation.

• Corrosion Science and Technology
• /
• v.6 no.6
• /
• pp.275-281
• /
• 2007

The effect of annealing on the pitting corrosion resistance of anodized Al-Mg alloy (AA5052) processed by equal-channel angular pressing (ECAP) was investigated by electrochemical techniques in a solution containing 0.2 mol/L of $AlCl_3$ and also by surface analysis. The Al-Mg alloy was annealed at a fixed temperature between 473 and 573 K for 120 min in air after ECAP. Anodizing was conducted for 40 min at $100-400A/m^2$ at 293 K in a solution containing 1.53 mol/L of $H_2SO_4$ and 0.0185 mol/L of $Al_2(SO_4)_3$. The internal stress generated in anodic oxide films during anodization was measured with a strain gauge to clarify the effect of ECAP on the pitting corrosion resistance of anodized Al-Mg alloy. The time required to initiate the pitting corrosion of anodized Al-Mg alloy was shorter in samples subjected to ECAP, indicating that ECAP decreased the pitting corrosion resistance. However, the pitting corrosion resistance was greatly improved by annealing after ECAP. The time required to initiate pitting corrosion increased with increasing annealing temperature. The strain gauge attached to Al-Mg alloy revealed that the internal stress present in the anodic oxide films was compressive stress, and that the stress was larger with ECAP than without. The compressive internal stress gradually decreased with increasing annealing temperature. Scanning electron microscopy showed that cracks occurred in the anodic oxide film on Al-Mg alloy during initial corrosion and that the cracks were larger with ECAP than without. The ECAP process of severe plastic deformation produces large internal stresses in the Al-Mg alloy; the stresses remain in the anodic oxide films, increasingthe likelihood of cracks. It is assumed that the pitting corrosion is promoted by these cracks as a result of the higher internal stress resulting from ECAP. The improvement in the pitting corrosion resistance of anodized AlMg alloy as a result of annealing appears to be attributable to a decrease in the internal stresses in anodic oxide films

• Composites Research
• /
• v.23 no.3
• /
• pp.31-36
• /
• 2010

A new material, carbon-nanofiber/polypyrrole (CNF/PPy) composite films, with different CNF weight ratios were fabricated electrochemically. Compared to the fabrication process based on simple physical mixing, the flexibility of the new film has been improved much better than the previous similar material. Pure PPy films were also fabricated by the new electrochemical process for the comparison of difference. Several SEM images were taken at two locations (electrode-side and solution-side) and at the cross section of the samples. Electrical conductivity of the composite films was measured by the four-probe method. The conductivity of the pure PPy film 0.013cm thick was 79.33S/cm. The CNF/PPy composite film with 5% CNF showed a conductivity of 93S/cm. One with 10% CNF showed a conductivity of 126 S/cm. The conductivity of PPy improves, as the CNF weight ratio increases. The good conductivity of CNF/PPy composites makes them a candidate for a small bending actuator. A bending sensor consists of PPy and PVDF, which can be operated in the air, was designed and the bending deflection was calculated using FEM.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.10 no.4
• /
• pp.229-236
• /
• 2012

A molten salt technology using $Li_2O$-LiCl has been extensively investigated to recover uranium metal from spent fuels in the field of nuclear energy. In the reduction process, it is an important point to maintain the concentration of $Li_2O$. $ZrO_2$ is inevitably contained in the spent fuels because Zr is one of the main components of fuel rod hulls. Therefore, the fate of $ZrO_2$ in $Li_2O$-LiCl molten salt has been investigated. It was found that $Li_2ZrO_3$ and $Li_4ZrO_4$ were formed chemically and electrochemically and they were not reduced to Zr. The recycling of $Li_2O$ is the key mechanism ruling the total reaction in the electrolytic reduction process. However, $ZrO_2$ will have a role as a $Li_2O$ sink.