• Journal of Electrochemical Science and Technology
• /
• 제6권3호
• /
• pp.106-110
• /
• 2015

This study investigates Cu(II) complexes of cyclam, propylene cross-bridged cyclam (PCB-cyclam), and propylene cross-bridged cyclam diacetate (PCB-TE2A) as homogeneous electrocatalysts for CO₂ reduction in comparison with Ni(II)-cyclam. It is found that Cu(II)-cyclam can catalyze CO₂ reduction at the potential close to its thermodynamic value (0.75 V vs. Ag/AgCl) in tris-HCl buffer (pH 8.45) on a glassy carbon electrode. Cu(II)-cyclam, however, suffers from severe demetalation due to the insufficient stability of Cu(I)-cyclam. Cu(II)-PCB-cyclam and Cu(II)-PCB-TE2A are revealed to exhibit much less demetalation behavior, but poor CO₂ reduction activities as well. The inferior electrocatalytic ability of Cu(II)-PCB-cyclam is ascribed to its redox potential that is too high for CO₂ reduction, and that of Cu(II)-PCB-TE2A to the steric hindrance preventing facile contact with CO₂ molecules. This study suggests that in addition to the redox potential and chemical stability, the stereochemical aspect has to be considered in designing efficient electrocatalysts for CO₂ reduction.

• Bulletin of the Korean Chemical Society
• /
• 제34권12호
• /
• pp.3835-3839
• /
• 2013

A new synthesis route for Pt nanoparticles by direct electrochemical reduction of a solid-state Pt ion precursor ($K_2PtCl_6$) is demonstrated. Solid $K_2PtCl_6$-supported polyethyleneimine (PEI) coatings on the surface of glassy carbon electrode were prepared by simple mixing of solid $K_2PtCl_6$ into a 1.0% PEI solution. The potential cycling or a constant potential in a PBS (pH 7.4) medium were applied to reduce the solid $K_2PtCl_6$ precursor. The reduction of Pt(IV) began at around -0.2 V and the reduction potential was ca. -0.4 V. A steady state current was achieved after 10 potential cycling scans, indicating that continuous formation of Pt nanoparticles by electrochemical reduction occurred for up to 10 cycles. After applying the reduction potential of -0.6 V for 300 s, Pt nanoparticles with diameters ranging from $0.02-0.5{\mu}m$ were observed, with an even distribution over the entire glassy carbon electrode surface. Characteristics of the Pt nanoparticles, including their performance in electrochemical reduction of $H_2O_2$ are examined. A distinct reduction peak observed at about -0.20 V was due to the electrocatalytic reduction of $H_2O_2$ by Pt nanoparticles. From the calibration plot, the linear range for $H_2O_2$ detection was 0.1-2.0 mM and the detection limit for $H_2O_2$ was found to be 0.05 mM.

• 공업화학
• /
• 제10권3호
• /
• pp.331-335
• /
• 1999

진이급속 산화물은 전기화학적 산소 발생/환원에 대한 bifunctional 촉매효과가 있어 금속-공기 이차전지와 같은 에너지 저장기술 개발에 연구대상이 되어왔다. Amorphous citrate precursor법을 이용하여 perovskite 구조를 갖는 La-Ca-Co 산화물과 pyrochlore 구조를 갖는 Pb-Ru 산화물을 제조하고, 이후 열처리법으로 표면적이 큰 전이금속 산화물 촉매분말을 제조하였다. PTFE 결합 기체확산형 전극의 충방전 실험을 통하여 전기화학적 산소발생/환원에 대한 좋은 촉매능을 가짐을 확인하였고, ${\pm}25mA/cm^2$의 전류밀도를 가하고 공기를 공급하면서 충방전 실험한 결과 100시간 이내에서 두촉매분말 모두 안정하였다. ACP법으로 제조한 perovskite 구조의 La0.6Ca0.4CoO3과 pyrochlore 구조의 Pb2Ru2O6가 이차전지용 공기전극 재료로 사용할 수 있음을 확인하였다.

• 전기화학회지
• /
• 제10권1호
• /
• pp.1-6
• /
• 2007

금 나노 입자를 회합시킨 흑연전극 표면에 mercaptopropionic acid(mpa)를 사용하여 자기조립 단층막(self-assembled monolayer: SAMs)을 생성시키고 이어서 도파민(dopa)과의 짝지움 반응을 통하여 Gr(Au)/mpa-dopa형의 수식된 전극을 제작하여 NADH의 전기촉매 산화반응에 적용하였다. 이 수식 전극이 전자전달반응속도와 반응과정에 대하여 연구하였다. 전극 표면에 고정된 도파민이 NADH와 이차반응 속도상수는 회전 전극법으로 0.1 M 인산염 완충용액(pH=7.0)에서 결정하였으며 그 값이 $5.06{\times}10^5M^{-1}s^{-1}$였고, $EC_{cat}$ 및 전자전달이 지배적인 과정이었다. 그러나 반응초기 즉, $10^{-3}s$ 이내에서는 이 전극에서 확산에 영향을 받으며 그 때 확산계수는 $4.64{\times}10^{-4}cm^2s^{-1}$이다.

• Journal of Electrochemical Science and Technology
• /
• 제1권1호
• /
• pp.31-38
• /
• 2010

In this study, we have demonstrated the fine structure effect of PdCo electrocatalyst on oxygen reduction reaction activity with different alloy composition and heat-treatment time. In order to identify the intrinsic factors for the electrocatalytic activity, various X-ray analyses were used, including inductively coupled plasma-atomic emission spectrometer, transmission electron microscopy, X-ray diffractometer, and X-ray Absorption Spectroscopy technique. In particular, extended X-ray absorption fine structure was employed to extract the structural parameters required for understanding the atomic distribution and alloying extent, and to identify the corresponding simulated structures by using FEFF8 code and IFEFFIT software. The electrocatalytic activity of PdCo alloy nanoparticles for the oxygen reduction reaction was evaluated by using rotating disk electrode technique and correlated to the change in structural parameters. We have found that Pd-rich surface was formed on the Co core with increasing heating time over 5 hours. Such core shell structure of PdCo/C showed that a superior oxygen reduction reaction activity than pure Pd/C or alloy phase of PdCo/C electrocatalysts, because the adsorption energy of adsorbates was apparently reduced by lowering the dband center of the Pd skin due to a combination of the compressive strain effect and ligand effect.

• Journal of Electrochemical Science and Technology
• /
• 제9권1호
• /
• pp.28-36
• /
• 2018

Metal-organic frameworks have recently been considered very promising modifiers in electrochemical analysis due to their unique characteristics among which tunable pore sizes, crystalline ordered structures, large surface areas and chemical tenability are worth noting. In the present research, $Cu(btec)_{0.5}DMF$ was electrodeposited on the surface of glassy carbon electrode at room temperature under cathodic potential and was initially used as the active materials for the detection of $H_2O_2$. The cyclic voltammogram of $Cu(btec)_{0.5}DMF$ modified GC electrode shows distinct redox peaks potentials at +0.002 and +0.212 V in 0.1 M phosphate buffer solution (pH 6.5) corresponding to $Cu^{(II)}/Cu^{(I)}$ in $Cu(btec)_{0.5}DMF$. Acting as the electrode materials of a non-enzymatic $H_2O_2$ biosensor, the $Cu(btec)_{0.5}DMF$ brings about a promising electrocatalytic performance. The high electrocatalytic activity of the $Cu(btec)_{0.5}DMF$ modified GC electrode is demonstrated by the amperometric response towards $H_2O_2$ reduction with a wide linear range from $5{\mu}M$ to $8000{\mu}M$, a low detection limit of $0.865{\mu}M$, good stability and high selectivity at an applied potential of -0.2 V, which was higher than some $H_2O_2$ biosensors.

• 공업화학
• /
• 제23권2호
• /
• pp.153-156
• /
• 2012

본 연구에서 직접 메탄올형 연료전지용 담지 촉매의 전기 화학적 효율을 높이기 위하여 담지 촉매의 합성을 위한 2가지 다른 방법을 조사하였다. 담지 촉매에 있어서 합금을 형성하여 동시 담지하는 방법과 금속을 순차적으로 담지하는 방법을 비교하였다. 금속의 총 함량을 20 wt%를 사용하였으며, Pt-Pd의 금속비를 1 : 2로 하였다. 순환 전류-전압곡선(CVs), TEM 이미지와 XRD분석을 이용하여 두가지 다른 방법으로 제조된 촉매 간의 전기화학적 특성, 입자의 평균 크기 및 결정의 구조 변화를 비교 분석하였다. 그 결과, 순차적 금속 담지 촉매가 동시 담지 촉매보다 단위 무게당 산화전류 수치를 나타내어 보다 높은 전기활성 특성을 보였다.

• Journal of Electrochemical Science and Technology
• /
• 제13권4호
• /
• pp.497-503
• /
• 2022

Spinel ferrites (Ni_xFe_3-xO₄; x = 0.25, 0.5, 0.75 and 1.0) have been prepared at 550℃ by egg white auto-combustion route using egg white at 550℃ and characterized by physicochemical (TGA, IR, XRD, and SEM) and electrochemical (CV and Tafel polarization) techniques. The presence of characteristic vibration peaks in FT-IR and reflection planes in XRD spectra confirmed the formation of spinel ferrites. The prepared oxides were transformed into oxide film on glassy carbon electrodes by coating oxide powder ink using the nafion solution and investigated their electrocatalytic performance for OER in an alkaline solution. The cyclic voltammograms of the oxide electrode did not show any redox peaks in oxygen overpotential regions. The iR-free Tafel polarization curves exhibited two Tafel slopes (b₁ = 59-90 mV decade^-1 and b₂ = 92-124 mV decade^-1) in lower and higher over potential regions, respectively. Ni-substitution in oxide matrix significantly improved the electrocatalytic activity for oxygen evolution reaction. Based on the current density for OER, the 0.75 mol Ni-substituted oxide electrode was found to be the most active electrode among the prepared oxides and showed the highest value of apparent current density (~9 mA cm^-2 at 0.85 V) and lowest Tafel slope (59 mV decade^-1). The OER on oxide electrodes occurred via the formation of chemisorbed intermediate on the active sites of the oxide electrode and follow the second-order mechanism.

• Korean Chemical Engineering Research
• /
• 제61권1호
• /
• pp.52-57
• /
• 2023

본 연구는 고성능 유연 전극 소재 개발을 위한 기초 연구로, 유연 전극 소재의 성능을 향상시키기 위해 금속 산화물 CuO nanoparticles (CuO NPs)를 도입하여 탄소나노튜브 섬유(carbon nanotube fiber; CNT fiber) 표면 위에 전기화학적 증착시켜 CNT fiber/CuO NPs 전극을 합성하고, 이를 전기화학적 비효소 글루코스 센서에 적용하였다. 이 전극의 표면 및 elemental composition 분석은 주사전자 현미경(SEM)과 에너지분산형 분광분석법(EDS)을 이용하였으며, 전극의 전기화학적 특성 및 글루코스에 대한 센싱 성능은 순환전압 전류법(CV)과 전기화학 임피던스법(EIS), 시간대전류법(CA)을 통해 조사되었다. CNT fiber/CuO NPs 전극은 CNT fiber의 우수한 특성과 함께 CuO NPs 도입에 따른 약 2.6배의 유효 전극면적(active surface area) 증가 효과와 11배 정도의 향상된 전자전달(electron transfer) 특성 및 우수한 전기적 촉매 활성(electrocatalytic activity) 덕분에 CNT fiber 유연 기반 전극의 글루코스 검출에 대한 성능이 개선되었다. 따라서, 본 연구를 기반으로 다양한 나노구조체를 활용한 고성능 유연 전극 소재 개발이 기대된다.

• 한국재료학회지
• /
• 제32권2호
• /
• pp.98-106
• /
• 2022

Metal-organic frameworks (MOFs) are widely used in various fields because they make it easy to control porous structures according to combinations of metal ions and organic linkers. In addition, ZIF (zeolitic imidazolate framework), a type of MOF, is made up of transition metal ions such as Co²⁺ or Zn²⁺ and linkers such as imidazole or imidazole derivatives. ZIF-67, composed of Co²⁺ and 2-methyl imidazole, exhibits both chemical stability and catalytic activity. Recently, due to increasing need for energy technology and carbon-neutral policies, catalysis applications have attracted tremendous research attention. Moreover, demand is increasing for material development in the electrocatalytic water splitting and metal-air battery fields; there is also a need for bifunctional catalysts capable of both oxidation/reduction reactions. This review summarizes recent progress of bifunctional catalysts for electrocatalytic water splitting and metal-air batteries using ZIF-67. In particular, the field is classified into areas of thermal decomposition, introduction of heterogeneous elements, and complex formation with carbon-based materials or polyacrylonitrile. This review also focuses on synthetic methods and performance evaluation.