• Journal of KIISE:Computing Practices and Letters
• /
• v.8 no.3
• /
• pp.289-294
• /
• 2002

A valid speech-sound block can be classified to provide important information for speech recognition. The classification of the speech-sound block comes from the MRA(multi-resolution analysis) property of the DWT(discrete wavelet transform), which is used to reduce the computational time for the pre-processing of speech recognition. The merging algorithm is proposed to extract valid speech-sounds in terms of position and frequency range. It needs some numerical methods for an adaptive DWT implementation and performs unvoiced/voiced classification and denoising. Since the merging algorithm can decide the processing parameters relating to voices only and is independent of system noises, it is useful for extracting valid speech-sounds. The merging algorithm has an adaptive feature for arbitrary system noises and an excellent denoising SNR(signal-to-nolle ratio).

• Fire Science and Engineering
• /
• v.34 no.3
• /
• pp.67-75
• /
• 2020

In this study, the risk of heat generation due to normal and overload currents that vary with the abnormal loosening angle of wire-connecting bolts were identified. The risks were analyzed based on the thermal characteristics to minimize the carbonization accidents of terminal blocks inside distribution panels typically used in industrial sites. We applied a method for measuring the heating temperature and temperature variations in the terminal blocks in real-time by installing a resistance temperature detector sensor board in the terminal block. The experimental results showed that the terminal block model with a low-rated current exhibited a higher heating temperature, thus, confirming the need to select the terminal block capacity based on load currents. Additionally, the higher the rated current of the terminal block with a high-rated current and the higher the degree of loosening, the faster the carbonization point. Such heating temperature monitoring enabled real-time thermal temperature measurement and a step-by-step risk level setting through thermal analysis. The results of the measurement and analysis of carbonization risks can provide a theoretical basis for further research regarding the risk of fire due to carbonization. Furthermore, the deterioration measurement method using the temperature sensor board developed in this study is widely applicable to prevent fires caused by poor electrical contact as well as risk-level management.

• Journal of Wellbeing Management and Applied Psychology
• /
• v.2 no.2
• /
• pp.19-37
• /
• 2019

Over the last few decades, the atmospheric carbon dioxide emission has been amplified to a great extent in Turkey. This amplification may cause global warming, climate change and environmental degradation in Turkey. Consequently, ecological condition and human life may suffer in the near future from these indicated threats. Therefore, an attempt was made to test the relationship among a number of expected factors and carbon dioxide emissions in the case of Turkey. The study covers the time series data over the period of 1970-2017. We employed the modern econometric techniques such as Johansen co-integration, ARDL bound testing approach and the block exogeneity. The results of the Johansen co-integration test show that there is a significant long-run relationship between carbon dioxide emissions and expected factors. The long-run elasticities of the ARDL model show that a 1% increase in the GDP per capita, electric consumption, fiscal development and trade openness will increase carbon dioxide emissions by 0.14, 0.52, 0.09 and 0.20% respectively. Further, our findings reveal that the environmental Kuznets curve (EKC) hypothesis and inverted U-shaped relationship between carbon dioxide emission and economic growth prevails. Therefore, the EKC hypothesis is valid and prevailing in the Turkish economy. The diagnostic test results show that the parameters of the ARDL model are credible, sTable and reliable in the current form. Finally, Block exogeneity analysis displays that all the expected factors are contributing significantly to carbon dioxide emissions in the Turkish economy.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.1
• /
• pp.29-37
• /
• 2018

Inrush current and fault current in a transformer need to be distinguished from one another. In order to do this, KEPCO uses a 2nd harmonic restraint/block method. We use two setting values for 2nd harmonic restraint; 15% and 10%. We also apply per-phase blocking method among various harmonic restraint methods. If the transformer is located at the radial system, we adjust 10% in the 2nd harmonic restraint, but this method is not enough to prevent mal-operations of the current differential relay and let us spend more time to change setting value again as the power system changes. In this paper, a more reasonable setting value for a 2nd harmonic blocking scheme in KEPCO is proposed. To present a proposed method, the fault data of the current differential relays which have occurred since 2009 are analyzed. To evaluate the performance of the proposed method, the results of the RTDS test for the current differential relay of the transformer by KEPCO are analyzed.

• Advances in Energy Research
• /
• v.4 no.1
• /
• pp.29-45
• /
• 2016

There has been a growing interest in the recent time for the development of solar power tower plants, which are mainly used for utility scale power generation. Combined heat and power (CHP) is an efficient and clean approach to generate electric power and useful thermal energy from a single heat source. The waste heat from the topping Brayton cycle is utilized in the bottoming HRSG cycle for driving steam turbine and also to produce process steam so that efficiency of the cycle is increased. A thermal storage system is likely to add greater reliability to such plants, providing power even during non-peak sunshine hours. This paper presents a conceptual configuration of a solar power tower combined heat and power plant with a topping air Brayton cycle. A simple downstream Rankine cycle with a heat recovery steam generator (HRSG) and a process heater have been considered for integration with the solar Brayton cycle. The conventional GT combustion chamber is replaced with a solar receiver. The combined cycle has been analyzed using energy as well as exergy methods for a range of pressure ratio across the GT block. From the thermodynamic analysis, it is found that such an integrated system would give a maximum total power (2.37 MW) at a much lower pressure ratio (5) with an overall efficiency exceeding 27%. The solar receiver and heliostats are the main components responsible for exergy destruction. However, exergetic performance of the components is found to improve at higher pressure ratio of the GT block.

• KIEAE Journal
• /
• v.12 no.2
• /
• pp.125-129
• /
• 2012

With the development of the industry, such as homes and industries of electric energy usage and thereby increase the supply of electrical energy for power generation facilities were also increased. Among them an increase in thermal power plants, such as Bottom Ash was accompanied by an increase in industrial waste. If fly ash is recycled, some ten thousand Fly Ash and Bottom Ash Landfill, the recycling rate is low in most. In this study, in order to resolve the problem of fly ash recycling Bottom Ash to take advantage of low physical and chemical characteristics were analyzed. Evaluation of Physical Properties of Bottom Ash In addition, through the evaluation of functional properties of additives chogyeol condensation of 1 hour or more, within 3 hours of closing, Flow has more than 190mm of wheel load resistance value is less than 3mm flooring developed to study the subsequent emphasis on the Properties is based. Through these studies by developing a functional flooring help with the problem of resource depletion, and losses due to reclamation and pollution is to prevent.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.1
• /
• pp.52-60
• /
• 1997

In genetic algorithms(GA), a crossover is performed only at one or two places of a chromosome, and the fixed probabilities of crossover and mutation have been used during the entire generation. A GA with dynamic mutation is known to be superior to GAs with static mutation in performance, but so far no efficient dynamic mutation method has been presented. Accordingly in this paper, a GA is proposed to perform a uniform crossover based on the nucleotide(NU) concept, where DNA and RNA consist of NUs and also a concrete way to vary the probabilities of crossover and mutation dynamically for every generation is proposed. The efficacy of the proposed GA is demonstrated by its application to the unimodal, multimodal and nonlinear control problems, respectively. Simulation results show that in the convergence speed to the optimal value, the proposed GA was superior to existing ones, and the performance of GAs with varying probabilities of the crossover and the mutation improved as compared to GAs with fixed probabilities of the crossover and mutation. And it also shows that the NUs function as the building blocks and so the improvement of the proposed algorithm is supported by the building block hypothesis.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.1
• /
• pp.43-53
• /
• 2001

WT(Wavelet Transform) is used to avoid blocking effect that is the disadvantage of JPEG using DCT(Discrete Cosine Transform). Because the proposed coding scheme is the same as JPEG, the proposed algorithm is compatible with that of JPEG. To achieve the goal, WT'ed image is reconstructed into 8$\times$8 coding block. Each coding block is quantized with the proposed weighting matrix that is derived from human visual characteristic and error analysis in WT'ed domain. By experiments, the proposed algorithm is superior to JPEG, in terms of PSNR(Peak Signal to Noise Ratio) and WMSE(Weighted Mean Square Error).

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.5
• /
• pp.42-49
• /
• 2009

The effects of various forces acting on concrete pole are analyzed using finite element method how the forces affect on ground displacement. The soil types, wind load location of anchor block embedded depth of pole, and distance between poles are varied to find out effects on lateral displacement. Anchor block is effective when it is located at 1/4 of embedded depth The displacement is decreases as elastic modulus increases. Concrete reinforcement for loosened ground is necessary for double poles because double poles cause large excavation. When embedded depth ratio decrease, lateral displacement increase as closer to ground surface. Large embedded depth is effective to reduce lateral displacement, and the distance between poles is not much large factor.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.8
• /
• pp.3103-3120
• /
• 2015

This paper presents a single-phase energy metering chip with built-in calibration function to measure electric power quantities. The entire chip consists of an analog front end, a filter block, a computation engine, a calibration engine, and an external interface block. The key design issues are how to reduce the implementation costs of the computation engine from repeatedly used arithmetic operations and how to simplify calibration procedure and reduce calibration time. The proposed energy metering chip simplifies the computation engine using time-division multiplexed arithmetic units. It also provides a simple and fast calibration scheme by using integrated digital calibration functionality. The chip is fabricated with 0.18-μm six-layer metal CMOS process and housed in a 32-pin quad-flat no-leads (QFN) package. It operates at a clock speed of 4096 kHz and consumes 9.84 mW in 3.3 V supply.