• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.239-243
• /
• 2008

In many literatures the researchers pointed out that the using metal foam will significantly enhance the performance of heat exchanger. This paper focuses on theory study of metal foam, including calculation method of properties of foam (permeability ��K, inertial coefficient f, fiber diameter $d_f$, and effective conductivity $k_e$), model of pressure drop and model of heat transfer. Theory analysis on the performance of heat exchanger will be presented here. Finally the optimal material will be obtained from theory calculation.

• Membrane Journal
• /
• v.26 no.5
• /
• pp.351-364
• /
• 2016

In recent decades, many researchers have tried to improve desalination performances of polyamide (PA) thin-film composite membranes (TFCs) by incorporating nanomaterials into a selective PA layer. This review focuses on PA-based nanocomposite membranes with high performances for energy-effective desalination in reverse osmosis. Carbon based nanomaterial (e.g., graphene oxide (GO), carbon nanotubes (CNT)) and/or other nanoparticles (e.g., zeolite, silica and etc.,) were applied to overcome the trade-off correlation between water permeability and salt rejection of current polymeric desalination membranes. Here, this brief review will discuss current studies of PA-based nanocomposite membranes with enhanced separation characteristics and provide the future research direction to achieve further improved desalination performances.

• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.362-370
• /
• 2001

The internal or external restraint of thermal and dry shrinkage movements could thus generate tensile stresses in concrete pavement for early traffic opening. Restrained shrinkage and thermal stresses could produce microcracks in concrete which increase its permeability and accelerate its long-term deterioration under weathering and load effects. Fiber reinforced concrete is an effective approach to the control of microcrack and crack development under tensile stresses. This study aims at evaluation of the durability of high early strength concrete for early traffic opening and increase of service life. Three different types of regulated-set cement which recently has been used much in Korea were adopted. Fibers were added and their mixtures were compared with plain high early strength concrete mixture. The use of fibers increased durability performance of high early strength concrete using regulated-set cement than the corresponding plain mixtures.

• Computers and Concrete
• /
• v.13 no.4
• /
• pp.423-436
• /
• 2014

Ground Granulated Blast Furnace Slag (GGBFS) is widely used as an effective partial cement replacement material. GGBFS inclusion has already been proven to improve several performance characteristics of concrete. GGBFS provides enhanced durability, including high resistance to chloride penetration and protection against alkali silica reaction. In this paper results of an experimental research work on influence of low-reactivity GGBFS (which is largely available in Iran) on the properties of mortars and concretes are reported. In the first stage, influence of GGBFS replacement level and fineness on the compressive strength of mortars was investigated using Taguchi method. The analysis of mean (ANOM) statistical approach was also adopted to develop the optimal conditions. Next, based on the obtained results, concrete mixtures were designed and water penetration, capillary absorption, surface resistivity, and compressive strength tests were carried out on highstrength concrete specimens at different ages up to 90 days. The results indicated that 7-day compressive strength is adversely affected by GGBFS inclusion, while the negative effect is less evident at later ages. Also, it was inferred that use of low-reactivity GGBFS (at moderate levels such as 20% and 30%) can enhance the impermeability of high-strength concrete since 28 days age.

• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.267-274
• /
• 2004

Theoretical analysis for predicting the heat transport limitations of screen mesh wick and sintered wick heat pipes was performed. The heat pipe diameter was 8mm and water was used for working fluid. For the 250 mesh, each capillary pressures and heat transport limitations, thermal resistances were analyzed according to the operating temperatures, wick thicknesses and inclination angles, based on the effective capillary radius (r$\_$c/), porosity ($\varepsilon$) and permeability (K). The wick capillary limitation was increased as the operating temperature and the wick thickness were increased, and generally the sintered wick showed higher heat transport limitations than that of the screen wick. The thermal resistance of the screen wick was higher than that of the sintered wick and both thermal resistances were linearly increased as the wick thickness was increased.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.120-124
• /
• 2003

This paper describes a MEMS-based micro-fluxgate magnetic sensing element using Ni$\_$0.8/Fe$\_$0.2/ film formed by electroplating. The micro-fluxgate magnetic sensor composed of a thin film magnetic core and micro-structure solenoids for the pick-up and the excitation coils, is developed by using MEMS technologies in order to take advantage of low-cost, small size and lower power consumption in the fabrication. A copper with 20${\mu}$m width and 3${\mu}$m thickness is electroplated on Cr (300${\AA}$) / Au (1500${\AA}$) films for the pick-up (42turn) and the excitation (24turn) coils. In order to improve the sensitivity of the sensing element, we designed the magnetic core into a rectangular-ring shape to reduce the magnetic flux leakage. An electroplated permalloy film with the thickness of 3${\mu}$m is obtained under 2000 gauss to induce magnetic anisotropy. The magnetic core has the high DC effective permeability of ~1,100 and coercive field of ~0.1 Oe. The fabricated sensing element using rectangular-ring shaped magnetic film has the sensitivity of about 150 V/T at the excitation frequency of 2 MHz and the excitation voltage of 4.4 V$\_$p p/. The power consumption is estimated to be 50mW.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.08a
• /
• pp.47-51
• /
• 2002

ECT(eddy currentign testing) is very effective technique to detect a flaw within a conductor. Co-based amorphous wire was used as a sensor head. The wire has almost 0 magneto-striction and high permeability. An uniform magnetic field was applied to 1mm thick copper plate and $25{\mu}m$ thick aluminum sheet conductor using spiral typed coil The size of the coil has $40mm{\times}40mm$ outer width and $8mm{\times}8mm$ inner width. The copper plate and aluminum sheet has 0.5mm and 0.1mm wide gap, respectively. The frequency range of applied field was 100kHz-600kHz. The induced voltage difference of 2.5mV was obtained in the maximum voltage and minimum one measured across the gap of the 1mm thick conductor. In the case of aluminum sheet, 0.4mV was obtained. From this results, the effectiveness of Co-based amorphous wire was confirmed in the ECT technique.

• Geosciences Journal
• /
• v.22 no.6
• /
• pp.1015-1026
• /
• 2018

This paper aims to investigate the good reservoir quality and hydrocarbon potentiality of the Khatatba Formation, Qasr Field in the Shoushan Basin of the North Western Desert, Egypt by combining results from log-based petrophysical analysis, petrographic description and images from scanning electron microscope (SEM). Promising reservoir units are initially identified and evaluated through well log analysis of three wells in the field of study. Petrophysical results are then compared with petrographic and SEM images from rock samples to identify features that characterize the reservoir quality. Well log results show that Khatatba Formation in the study area has good sandstone reservoir intervals from depths ranging from 12848 ft to 13900 ft, with good effective porosity records of 13-15% and hydrocarbon saturations of greater than 83%. Petrographic analysis of these sandstone reservoir units indicate high concentrations of vacant pore spaces with good permeability that can be easily occupied by hydrocarbon. The availability of these pore spaces are attributed to pore-enhancing diagenetic features, mainly in the form of good primary porosity and dissolution. SEM images and EDX analysis confirmed the presence of hydrocarbon, therefore indicating a good hydrocarbon-storing potential for the Khatatba Formation sandstones.

• Korean Journal of Soil Science and Fertilizer
• /
• v.19 no.3
• /
• pp.251-268
• /
• 1986

Selecting a site for the safe disposal of radioactive waste requires the evaluation of a wide range of geologic, mineralogic, hydrologic, and physicochemical properties. Although highly diverse, these properties are in fact interrelated. Site requirements are also diverse because they are influenced by the nature of the radionuclides in the waste, for example, their half-lives, specific energy, and chemistry. A fundamental consideration in site selection is the mineralogy of the host rock, and one of the most ubiquitous mineral groups is clay minerals. Clays and clay minerals as in situ lithologic components and engineered barriers may playa significant role in retarding the migration of radionuclides. Their high sorptivity, longevity (stability), low permeability, and other physical factors should make them a very effective retainer of most radionuclides in nuclear wastes. There are, however, some unanswered questions. For example, how will their longevity and physicochemical properties be influenced by such factors as radionuclide concentration, radiation intensity, elevated temperatures, changes in redox condition, pH, and formation fluids for extended periods of time? Understanding of mechanisms affecting clay mineral-radionuclide interactions under prevailing geochemical conditions is important; however, the utilization of experimental geochemical information related to physicochemical properties of clays and clay-bearing materials with geohydrologic models presents a uniquely challenging problem in that many assessments have to be based on model predictions rather than on experiments. These are high-priority research investigations that need to be addressed before complete reliance for disposal area performance is made on clays and clay minerals.

• Journal of the Korean Society of Safety
• /
• v.34 no.4
• /
• pp.103-110
• /
• 2019

Underwater works are indispensable in the coastal and ocean engineering fields, and the reliance on manpower is higher than land works. Divers who work for a long time in a high-pressure underwater environment are always exposed to the risks of diving-related diseases. To prevent them, proper planning, operation, and management of diving by a supervisor with professional diving knowledge are required. This study provides the basic data for supervisors to plan, operate, and manage air diving for safe and efficient work in underwater construction sites. It is well-known that air diving simulations using the varying permeability model (VPM) require a longer decompression time as the water depth and the residence time in water increase. Therefore, it is crucial to have a proper surface interval through repetitive diving rather than single diving to improve the safety of the divers and the efficiency of underwater work. Furthermore, coastal and ocean engineers who manage and supervise underwater construction work must acquire expert knowledge on diving before they can plan, operate, and manage diving.