• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.8
• /
• pp.643-650
• /
• 2000

Density-of-states effective mass(m*$_{d}$) and conductivity mass(m*$_{c}$)for Ge and Ge$_{0.8}$/Sn$_{0.2}$ are obtained by using 8$\times$8 k.p and strain Hamiltonians. It is shown that m*$_{d}$ and m*$_{c}$ for electrons in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) and Ge$_{0.8}$/Sn$_{0.2}$/Ge(001) are much smaller than those for electrons in relaxed Ge mainly due to the increase of interaction caused by the strain between the conduction band and valence bands at the $\Gamma$ point. The lift of degeneracy in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) and Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) makes m*$_{d}$ and m*$_{c}$ for holes smaller than those in relaxed Ge and results in the decrease of the interband scattering as well as interband scattering. The decrease of the interband scattering is more obvious in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) because of its large splitting energy between the heavy hole and light hole band. Therefore, Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) is expected to be good candidate for the development of ultra high-speed CMOS device.CMOS device.eed CMOS device.CMOS device.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2626-2631
• /
• 2007

Air-water two phase natural circulation flow in the T-HERMES (Thermo-Hydraulic Evaluation of Reactor cooling Mechanism by External Self-induced flow)-1D experiment has been evaluated to verify and evaluate the experimental results by using the RELAP5/MOD3 computer code. The RELAP5 results have shown that an increase in the coolant inlet area leads to an increase in the water circulation mass flow rate. However, the water outlet area does not effective on the water circulation mass flow rate. As the coolant outlet moves to a lower position, the water circulation mass flow rate decreases. The water level is not effective on the water circulation mass flow rate. As the height increases in the air injection part, the void fraction increases. However, the void fraction in the upper part of the air injector maintains a constant value. An increase in the air injection mass flow rate leads to an increase in the local void fraction, but it is not effective on the local pressure.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.3
• /
• pp.47-61
• /
• 2012

parallel transmitting system with channel bonding method have been proposed to transmit mass content such as UHD(Ultra High Definition) in HFC(Hybrid Fiber Coaxial) networks. However, this system may lead to channel resource problem because the system needs many channels to transmit mass content. In this paper, we analyze three effective bandwidth approximation algorithms to use the bonding channel efficiently. These algorithms are the effective bandwidth of Gaussian approximation method algorithm proposed by Guerin, the effective bandwidth based on statistics of video frames proposed by Lee and the effective bandwidth based on Gaussian traffic proposed by Nagarajan. We also evaluate compatibility of algorithms to the mass broadcasting service. OPNET simulator is used to evaluate the performance of the algorithms. For accuracy of simulation, we make mass source from real HD broadcasting stream.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2713-2718
• /
• 2003

Some of manufacturing tasks such as sawing task often requires continuous impulsive motion. In case of sawing task, such impulsive motions can be observed between the teeth of the saw and the object. The amount of the external impulse exerted on the object has been treated as an important control parameter. The purpose of this work is to introduce a new concept of an effective mass in sawing task and to suggest an external impulse model in sawing task. A normalized impulse ellipsoid reflecting the velocity direction is employed to visualize the impact geometry. Experiments are performed for soft and hard workpieces to justify the external impulse model in the sawing task. It is demonstrated through simulation and experiment that the proposed external impulse model is effective to characterize the impact property.

• Journal of Applied Reliability
• /
• v.18 no.3
• /
• pp.229-239
• /
• 2018

Purpose: There is a difficulty in Environmental Stress Screening (ESS) test design for weapon system's electrical/electronic components/products in small and medium-sized enterprises. To overcome this difficulty, I propose an easy ESS test design approach algorithm that is optimized with only one environment tolerance design information parameter (${\Delta}T$). Methods: To propose the mass production weapon system ESS test design for cost-effective optimization, I define an optimum cost-effective mathematical model ESS test algorithm model based on modified MIL-HDBK-344, MIL-HDBK-2164 and DTIC Technical Report 2477. Results: I clearly confirmed and obtained the quantitative data of ESS effectiveness and cost optimization along our ESS test design algorithm through the practical case. I will expect that proposed ESS test method is used for ESS process improvement activity and cost cutting of mass production weapon system manufacturing cost in small and medium-sized enterprises. Conclusion: In order to compare the effectiveness of the proposed algorithm, I compared the effectiveness of the existing ESS test and the proposed algorithm ESS test based on the existing weapon system circuit card assembly for signal processing. As a result of the comparison, it was confirmed that the test time was reduced from 573.0 minutes to 517.2minutes (9.74% less than existing test time).

• Journal of the Earthquake Engineering Society of Korea
• /
• v.26 no.5
• /
• pp.203-209
• /
• 2022

A simplified method for earthquake response analysis of a rectangular liquid storage tank is proposed with fluid-structure interaction considered. In order to simplify the complex three-dimensional structural behavior of a rectangular liquid storage tank, it is assumed that structural deformation does not occur in the plane parallel to the direction in which the earthquake ground motion is applied but in the plane perpendicular to the direction. The structural deformation is approximated by combining the natural modes of the simple beam and the cantilever beam. The hydrodynamic pressure, the structure's mass and stiffness, and the hydrodynamic pressure's added mass are derived by applying the Rayleigh-Ritz method. The natural frequency, structural deformation, pressure, effective mode mass, and effective mode height of the rectangular liquid storage tank are obtained. The structural displacement, hydrodynamic pressure, base shear, and overturning moment are calculated. The seismic response analysis of an example rectangular liquid storage tank is performed using the proposed simplified approach, and its accuracy is verified by comparing the results with the reference solution by the finite element method. Existing seismic design codes based on the hydrodynamic pressure in rigid liquid storage tanks are observed to produce results with significant errors that cannot be ignored.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.209-216
• /
• 1994

Rock mass classifications have played an indispensable role in underground construction for several decades. An important issue in rock mass classifications is the selection of the parameters of greatest significance. There appears to be no single parameter that can fully describe a jointed rock mass for underground construction design. In this paper. We find some problems shen applied rock mass classification for underground construction in domestic, analyze the most significant parameters and parameters correlation influencing the behavior of a rock mass, and suggest the Simplied Rock Mass Rating system based on RMR method for effective underground supports.

• New & Renewable Energy
• /
• v.2 no.2 s.6
• /
• pp.75-80
• /
• 2006

The effective thermal conductivities of $Mm(La_{0.6-0.8})Ni_{4.0}Co_{0.6}Mn_{0.2}Al_{0.2}$ [TL-492] with hydrogen and helium have been examined. Experiment results show that pressure has great influence on effective thermal conductivity in low pressure range [below 0.5 MPa]. And that influence decreases rapidly with increase of gas pressure. The reason is at low pressure, the mean free path of gas becomes greater than effective thickness of gas film which is important to the heat transfer mechanism in this research. And, carbon fibers have been used to try to enhance the poor thermal conductivity of TL-492. Three types of carbon fibers and three mass fractions have been examined and compared. Naturally, the highest effective thermal conductivity has been reached with carbon fiber which has highest thermal conductivity, and highest mass fraction. This method has acquired 4.33 times higher thermal conductivity than pure metal hydrides with quite low quantity of additives, only 0.99 wt% of carbon fiber. This is a good result comparing to other method which can reach higher effective thermal conductivity but needs much higher mass fraction of additives too.

• The Korean Journal of Ecology
• /
• v.27 no.5
• /
• pp.301-306
• /
• 2004

The sensitivity to Cd of three ectomycorrhizal fungi, Paxillus involutus, Suillus bovinus and Rhizopogon subcaerulescens, was assessed and compared in terms of radial growth and dry mass production, using both agar and liquid culture. The radial growth of S. bovinus and R. subcaerulescens was significantly reduced at the lowest concentration (0.1mg Cd/L). The 50% effective concentration (EC$_{50}$) values calculated from radial growth rates of the ectomycorrhizal fungi showed that the sensitivity of the fungi to Cd was greatest in S. bovinus and lowest in R. subcaerulescens. Cadmium addition also significantly decreased dry mass production of the ectomycorrhizal fungi. The sensitivity of the fungi to Cd in terms of dry mass production, was greatest in S. bovinus and lowest in P. involutus. Higher growth rates of P. involutus and melanisation of R. subcaerulescens appeared to contribute to reduced Cd toxicity.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1992.04a
• /
• pp.26-29
• /
• 1992

Modern tall buildings are subject to wind induced oscillations. Those oscillations can cause discomfort to the occupants. To control these motions, tuned mass dampers have been used. In this paper, component node synthesis, based on Lagrange multipliers formulation. is applied to the along-wind motion of tall buildings with multiple tuned mass dampers. Spectral densities of accelerations of top floor are compared by changing the numbers and locations of tuned mass dampers. It is found that multiple tuned mass dampers can be more effective than single tuned mass damper in reducing the acceleration response.