• 한국전산구조공학회논문집
• /
• 제18권2호
• /
• pp.169-179
• /
• 2005

탄성 및 비탄성좌굴 고유치해석법을 이용하여 강절프레임의 보-기둥부재의 유효좌굴길이를 산정하는 개선된 방법을 제시한다. 이를 위하여 먼저 설계기준에 제시된 압축재의 내하력 곡선식으로부터 접선계수이론(tangent modulus theory)에 근거하여 세장비-접선계수(tangent modulus), 응력-변형률 곡선식을 유도한다. 이때 안정함수를 이용하여 보-기둥요소의 접선강성행렬을 얻고, 비탄성 좌굴 고유치해석법을 제시하며 이를 이용하여 유효좌굴길이를 산정하는 방법을 제시한다. 해석예제를 통하여 강절프레임에 탄성 및 비탄성좌굴해석법에 의한 유효좌굴길이 비교결과를 제시하고, 매개변수 연구 결과를 제시한다.

• Structural Engineering and Mechanics
• /
• 제27권4호
• /
• pp.477-499
• /
• 2007

The main purpose of this paper is to investigate the ultimate behavior of steel cable-stayed bridges with design variables and compare the validity and applicability of computational methods for evaluating ultimate load capacity of cable-stayed bridges. The methods considered in this paper are elastic buckling analysis, inelastic buckling analysis and nonlinear elasto-plastic analysis. Elastic buckling analysis uses a numerical eigenvalue calculation without considering geometric nonlinearities of cable-stayed bridges and the inelastic material behavior of main components. Inelastic buckling analysis uses an iterative eigenvalue calculation to consider inelastic material behavior, but cannot consider geometric nonlinearities of cable-stayed bridges. The tangent modulus concept with the column strength curve prescribed in AASHTO LRFD is used to consider inelastic buckling behavior. Detailed procedures of inelastic buckling analysis are presented and corresponding computer codes were developed. In contrast, nonlinear elasto-plastic analysis uses an incremental-iterative method and can consider both geometric nonlinearities and inelastic material behavior of a cable-stayed bridge. Proprietary software ABAQUS are used and user-subroutines are newly written to update equivalent modulus of cables to consider geometric nonlinearity due to cable sags at each increment step. Ultimate load capacities with the three analyses are evaluated for numerical models of cable-stayed bridges that have center spans of 600 m, 900 m and 1200 m with different girder depths and live load cases. The results show that inelastic buckling analysis is an effective approximation method, as a simple and fast alternative, to obtain ultimate load capacity of long span cable-stayed bridges, whereas elastic buckling analysis greatly overestimates the overall stability of cable-stayed bridges.

• Geomechanics and Engineering
• /
• 제22권4호
• /
• pp.361-374
• /
• 2020

This paper is concerned with the thermoelastic bending of FG beams resting on two-layer elastic foundations. One of these layers is Winkler springs with a variable modulus while the other is considered as a shear layer with a constant modulus. The beams are considered simply supported and subjected to thermo-mechanical loading. Temperature-dependent material properties are considered for the FG beams, which are assumed to be graded continuously across the panel thickness. The used theories contain undetermined integral terms which lead to a reduction of unknowns functions. Several micromechanical models are used to estimate the effective two-phase FG material properties as a function of the particles' volume fraction considering thermal effects. Analytical solutions for the thermo-mechanical bending analysis are obtained based on Navier's method that satisfies the boundary conditions. Finally, the numerical results are provided to reveal the effect of explicit micromechanical models, geometric parameters, temperature distribution and elastic foundation parameters on the thermoelastic response of FG beams.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.619-624
• /
• 2012

In this study, MMT/fiber/polymer composites were fabricated by impregnating chopped strand glass mat into a vinylester resin mixed with clay. Tensile tests has been performed by using a universal testing machine to determine the effect of MMT addition on the tensile properties of MMT/chopped strand glass fiber/vinylester composites. And some pictures which are magnified cross section of breaking parts are has been taken by using a FE-SEM to confirm the behavior at breaking. The contents ratio of MMT applied in the composites were 0.5, 1.0, 1.5, and 2.0 wt% respectively. It has been found that the tensile strength and elastic modulus of MMT/chopped strand glass fiber/vinylester composites were improved at a proper content of MMT. Tensile strength and elastic modulus were maximized at a content of 1.0 wt% due to most effective dispersion of MMT. On the contrary, the failure strain was increased as MMT content was increased.

• 전산구조공학
• /
• 제11권1호
• /
• pp.227-235
• /
• 1998

임의의 단면과 임의의 경계조건을 갖는 구조요소에 대한 진동해석 방법은 1974년 D.H.Kim에 의해 제시되었다. 이 방법은 복합적층판을 포함한 2차원 문제의 1차모드 진동해석으로 확장하였다. passive와 active 제어 장치를 가지는 빌딩슬래브는 탄성지지된 것과 같이 거동한다. 이 논문에서는 표제의 문제를 해결하기 위하여 이 방법을 사용하였으며, 진동해석에 필요한 처짐 영향면을 유한 차분법을 사용하여 구하였다. 고유 진동수에 대한 슬래브 강성-기초탄성계수의 상대적인 값의 영향을 고찰하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.423-430
• /
• 2002

A feasibility of a trial test method was evaluated analytically, in which the elastic modulus of a soil deposit was tried to estimate by analyzing dynamic signals measured during conducting the SPT. If there existed a reliable relationship between the impedance ratio of a rod to a soil and the amplitude ratio of a reflected to an incident wave signal at the tip of steel rod contacting the soil surface, it was expected that one could determine the impedance of soil, and then roughly estimate the elastic modulus from the impedance. For a simple rod-soil system, the existence of the relevant relationship was verified in this study by analyzing computed wave signals propagating up and down through the rod. On the basis of these results, thus, a potential of the test method to practical applications could be seen. However, apparent theoretical shortcomings possessed in this approach were also realized since the soil part had an unconfined contact area where contacted with the rod. Therefore, it was concluded that further studies needed to be conducted, in which the reliable theoretical relationship between the impedance and the amplitude ratio as well as the effective contacting soil area contributing to wave reflection should be justified.

• 한국도로학회논문집
• /
• 제3권1호
• /
• pp.185-197
• /
• 2001

본 연구는 온도에 따라 특성이 변하는 아스팔트 콘크리트의 파괴인성을 규명하기 위하여 기존의 유효균열 모델을 수정하는 연구를 다루고 있다. 본래의 ECM모델은 콘크리트와 같은 고체에 적용되도록 개발되어 재료의 포아슨 비를 고려하지 않는다. 하지만 아스팔트 콘크리트는 온도변화에 민감하여 온도에 따라 포아슨 비가 변화하므로 다양한 온도하에서 정확한 파괴 특성을 알기 위해서는 포아슨 비가 고려되어져야 한다. 3개의 개질아스팔트 결합재를 포함한 4가지 결합재를 사용하여 밀입도 아스팔트 혼합물을 제조하여 초기균열 보에 대한 3점 휨 시험을 $-5^{\circ}C$부터 $-35^{\circ}C$까지에서 수행하였다. 탄성계수, 휨강도 및 파괴인성을 시험을 통하여 구하였다. 시험결과 포아슨비가 고려되는 수정 ECM 공식을 사용하므로서 보다 정확한 값들을 얻을 수 있었다. 폴리머 개질 아스팔트 혼합물이 일반아스팔트 혼합물에 비하여 더 낮은 저온하에서 더 높은 강성과 파괴인성을 유지함을 알 수 있었다.

• 한국강구조학회 논문집
• /
• 제18권2호
• /
• pp.225-237
• /
• 2006

김 등(2005a, b)의 연구를 확장시켜 시스템 좌굴 고유치해석법을 이용한 유효좌굴길이 산정법과 2차 탄성해석기법을 이용한 2차모멘트를 이용하여 축력과 휨모멘트를 받는 라멘구조의 보-기둥부재에 대한 개선된 좌굴설계법을 제안한다. 이를 위하여 먼저 국내도로교설계기준, AISC-LRFD, SRC의 각 설계기준에 제시된 내하력 기준식을 이용하여 응력-변형율 관계를 유도하고, 이를 이용한 탄성 및 비탄성 좌굴 고유치해석을 이용한 유효좌굴길이 산정법을 고찰한다. 또한 라멘구조에 대하여 AISC-LRFD에서 제시하고 있는 좌굴 안정성 검토식과 본 연구에서 제시하는 안정성 검토식을 해석예제를 통하여 비교, 검토를 행한다.

• 한국정밀공학회지
• /
• 제16권8호
• /
• pp.138-148
• /
• 1999

Thermal deformations of tension mask under localized heating are analyzed using finite element method and electron beam landing shifts are predicted by the analysis results. In CRT, electron beam landing shifts due to thermal deformations of the tension mask make the color purity of screen worse. In order to get the final results of thermal deformations, firstly the tension processes of the mask and following welding processes between the tensional mask and rail must be analyzed sequentially. And then, nonlinear transient thermo-elastic finite element analysis is performed on every part inside CRT including tension mask, wherein thermal radiation is a main heat transfer mechanism. Because the tension mask has numerous slits, the effective thermal conductivity and effective and effective elastic modulus is calculated, and the tension mask is modeled as a shell without slits. From the displacement results of tension mask, electron beam landing shifts is calculated directly. Experiments are performed to confirm our analysis results. Temperature distributions and beam landing shifts of tension mask are measured and the results are in good agreement with those of analyses.

• 한국재료학회지
• /
• 제14권6호
• /
• pp.436-442
• /
• 2004

Elastic and plastic deformation behaviors of the high purity aluminum and the silica glass were studied using nanoindentation and finite element analysis(FEA) techniques. Berkovich- and cone-type indenters were used for the nanoindentation test. Deformation behaviors and nanoindent profiles of elastic, elastic-plastic or plastic materials were clearly visualized by FEA simulation. Effects of the penetration depth and strain hardening on the deformation behavior were examined. Pile-up and sink-in behaviors were studied by using FEA technique. Degree of pile-up or sink-in was found to be a function of the ratio of elastic modulus to yield strength of materials. FEA was found to be an effective method to study deformation behaviors of materials under nanoindentation, especially in the case when pile-up or sink-in phenomena occurred.