• 한국측량학회지
• /
• 제38권4호
• /
• pp.317-325
• /
• 2020

무인항공사진측량은 저비용, 고효율의 장점으로 최근 고정밀의 신속 공간정보 데이터 취득 수단으로 떠오르고 있다. 하지만 무인항공영상의 정량적인 품질 검증 방법이나 인증에 대한 구체적인 절차와 세부규정이 미흡하다. 또한, 영상 품질에 대한 검증 수단이 영상의 해상도와 함께 명암의 대비 정도를 분석 할 수 있는 MTF (Modulation Transfer Function) 분석이나 경계반응 분석이 아니라 단순히 GSD (Ground Sample Distance) 만으로 품질을 평가하는 실정이다. 이에 본 연구에서는 무인항공영상 품질 분석에서 경계반응 분석의 필요성을 확인하기 위해 GSD 분석과 함께 Slanted edge target을 이용한 경계반응 분석을 실시하였다. 또한, 작업자가 간편하게 경계반응을 분석할 수 있도록 Matlab GUI 기반 tool을 제작하였다. 연구 결과, 동일한 GSD 임에도 불구하고 경계 반응 분석 결과는 상이하게 나타나 경계반응 분석의 필요성을 확인할 수 있었다. 아울러, 무인항공영상의 경계반응 분석 수치는 무인항공기에 탑재한 카메라의 성능에 비례함을 알 수 있었다.

• Wind and Structures
• /
• 제25권2호
• /
• pp.157-176
• /
• 2017

2-edge box girder bridges have been widely used in civil engineering practice. However, these bridges show weakness in aerodynamic stability. To overcome this weakness, additional attachments, such as fairing and flap, are usually used. These additional attachments can increase the cost and decrease the constructability. Some previous researchers suggested an aerodynamically stabilized 2-edge box girder section, giving a slope to the edge box instead of installing additional attachments. However, their studies are limited to only dynamic stability, even though static aerodynamic coefficients are as important as dynamic stability. In this study, focus was given to the evaluation of static aerodynamic response for a stabilized 2-edge box girder section. For this, the slopes of the edge box were varied from $0^{\circ}$ to $17^{\circ}$ and static coefficients were obtained through a series of wind tunnel tests. The results were then compared with those from computational fluid dynamics (CFD) analysis. From the results, it was found that the drag coefficients generally decreased with the increasing box slope angle, except for the specific box slope range. This range of box slope varied depending on the B/H ratio, and this should be avoided for the practical design of such a bridge, since it results in poor static aerodynamic response.

• The Korean Journal of Physiology and Pharmacology
• /
• 제14권6호
• /
• pp.413-417
• /
• 2010

To understand the function of edges in perception of moving objects, we defined four questions to answer. Is the focus point in visual motion detection of a moving object: (1) the body or the edge of the object, (2) the leading edge or trailing edge of the object, (3) different in scotopic, mesopic and photopic luminance levels, or (4) different for colored objects? We measured the Optomotor Response (OMR) and Edge Triggering Response (ETR) of goldfish. We used a square and sine wave patterns with black and red stripes and a square wave pattern with black and grey stripes to generate OMR's and ETR's in the goldfish. When we used black and red stripes, the black leading edges stimulated an ETR under scotopic conditions, red leading edges stimulated an ETR under photopic conditions, and both black and red leading edges stimulated an ETR under mesopic luminance levels. For black and gray stripes, only black leading edges stimulated an ETR in all three light illumination levels. We observed less OMR and ETR results using the sine wave pattern compared to using the square wave pattern. From these results, we deduced that the goldfish tend to prefer tracking the leading edge of the pattern. The goldfish can also detect the color of the moving pattern under photopic luminance conditions. We decided that ETR is an intriguing factor in OMR, and is suitable as a method of behavioral measurement in visual system research.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.292-294
• /
• 2005

The emerging peer-to-peer (P2P) model has recently gained a significant attention due to its high potential of sharing various resources among networked users. Super-peer unstructured P2P systems have been found very effective by dividing the peers into two layers, super-peer and edge peer. Super peer deal with all Queries instead of edge peers. The existing P2P systems assume all super peers have equal roles and capabilities. However, all super peers don't so that edge peers should select the best super peer in order to handle Queries well. In this paper, we suggest the ISP2P (Intelligent Super-peer based P2P) which allows to select the best super peer to the edge peers. We classify super peers according as the capacity of a edge peer to a super peer. We show that considering the quality of a edge peer to a super peer can improve the performance of the response time and bandwidth.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 Ⅳ
• /
• pp.2216-2219
• /
• 2003

Accurate speech region detection and automatic syllable segmentation is important part of speech recognition system. In automatic speech recognition system, they are needed for the purpose of accurate recognition and less computational complexity, In this paper, we Propose improved syllable segmentation method using ramp edge detection method and residual signal Peak energy. These methods were used to ensure accuracy and robustness for endpoint detection and syllable segmentation system. They have almost invariant response to various background noise levels. As experimental results, we obtained the rate of 90.7％ accuracy in syllable segmentation in a condition of accurate endpoint detection environments.

• 조명전기설비학회논문지
• /
• 제19권1호
• /
• pp.175-181
• /
• 2005

본 논문에서는 자동화 시스템의 고속 정밀 제어를 위한 퍼지-PLL 제어기를 제안한다. 기존의 PLL 제어기는 넓은 데드존 때문에 지터 잡음을 발생하고, 긴 지연시간 때문에 고속 동작의 정밀제어에는 부적합 하다. 본 논문에서는 이러한 문제를 해결하기 위하여, 제어영역을 고속 제어와 정밀제어 영역으로 구분한다. 먼저 퍼지 제어 기법을 적용하여 신속한 과도응답을 수행하고, 오차가 설정된 범위에 진입하면 새로운 위상 주파수 검출기를 설계한 PLL 제어기를 사용하여 정밀제어를 수행한다. 제안된 다중 구조의 위상 주파수 검출기는 데드존과 지터 잡음을 개선하고, 상승 에지에서 동작하는 P-PFD와 하강 에지에서 동작하는 N-PFD로 구성하여 PLL의 응답 특성을 향상 시킨다.

• 한국컴퓨터정보학회논문지
• /
• 제23권1호
• /
• pp.25-32
• /
• 2018

In this paper, we propose an edge detection algorithm for auto focus of infrared camera. We designed and implemented the edge detection of infrared image by using a spatial filter on FPGA. The infrared camera should be designed to minimize the image processing time and usage of hardware resource because these days surveillance systems should have the fast response and be low size, weight and power. we applied the $3{\times}3$ mask filter which has an advantage of minimizing the usage of memory and the propagation delay to process filtering. When we applied Laplacian filter to extract contour data from an image, not only edge components but also noise components of the image were extracted by the filter. These noise components make it difficult to determine the focus state. Also a bad pixel of infrared detector causes a problem in detecting the edge components. So we propose an adaptive edge detection filter that is a method to extract only edge components except noise components of an image by analyzing a variance of pixel data in $3{\times}3$ memory area. And we can detect the bad pixel and replace it with neighboring normal pixel value when we store a pixel in $3{\times}3$ memory area for filtering calculation. The experimental result proves that the proposed method is effective to implement the edge detection for auto focus in infrared camera.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.326-331
• /
• 2005

In this study, bearing response in single lap riveted joint is investigated by menas of single lap shear specimens with different types of adherend and fastener. Single lap shear specimen consists of adherend of SUS403 and carbon fabric/epoxy composite. Rivet of Avdel 2691 with 9.6mm diameter is used. Two types of fastener in single lap riveted joint are considered. One is a single lap shear specimen with single fastener, and the other is a single lap shear specimen with double fasteners. Especially, in case of single lap shear specimen with single fastener, the width of the specimen is varied as 2D, 3D, 4D, 6D at a fixed edge distance of 3D. Also the edge distance of the specimen is varied as 1.0D, 1.5D, 2.0D, 2.5D, 3.0D at a fixed width of 4D. In case of single lap shear specimen with double fasteners, two types of specimen are considered. One is a specimen with the width of 6D and edge distance of 3D. The other is a specimen with the width of 4D and edge distance of 2D. Here D designates the hole diameter for riveted joint.

• 한국정밀공학회지
• /
• 제18권5호
• /
• pp.130-136
• /
• 2001

Generally, a metal slitting saw is plain milling cutter with thickness less than 3/16 inch. This is used for cutting a workpiece that high dimensional accuracy and surface finish is necessary. A small thin milling cutter like a metal slitting saw is useful for machining a narrow groove. In this case, built up edge(BUE) is severe at each tooth and affects the surface integrity of the machined surface and tool wear. It is well known that tool geometry and cutting conditions are decisive factors to remove BUE. In this paper, we optimized the geometry of the milling cutter and selected cutting conditions to remove BUE by the experimental investigation. The experiment was planned with Taguchi method based on the orthogonal array of design factors such as coating, rake angle, number of tooth, cutting speed, feed rate. Response table was obtained from the number of built-up edge generated at tooth. The optimized tool geometry and cutting conditions could be determined through response table. In addition, the relative effect of factors was identified bh the analysis of variance (ANOVA). Finally, coating and cutting speed turned out important factors for BUE.

• Structural Engineering and Mechanics
• /
• 제83권4호
• /
• pp.451-463
• /
• 2022

The present study deals with forced vibrations of an elastic circular plate supported along its circular edge by unilateral elastic springs. The plate is assumed to be subjected to a uniformly distributed and a concentrated load. Under the combination of these loads, equations of motion are explicitly derived for static and dynamic response analyses by assuming a series of the displacement functions of time and other unknown parameters which are to be determined by employing Lagrangian functional. The approximate solution is sought by applying the Lagrange equations of motions by using the potential energy of the external forces that includes the contributions of the edge forces and the external moments, i.e., those of the effects of the boundary condition to the analysis. For the numerical treatment of the problem in the time domain, the linear acceleration procedure is adopted. The tensionless character of the support is taken into account by using an iterative process and, the coordinate functions for the displacement field are selected to partially fulfill the boundary conditions so that an acceptable approximation can be achieved faster. Numerical results are presented in the figures focusing on the nonlinearity of the problem due to the plate lift-off from the unilateral springs at the edge support.