• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.55-56
• /
• 2011

This study is to investigate the engineering properties of low heat concrete incorporating improved ternary blended cement by combining OPC(original portland cement), blast furnace slag and fly ash. The results were summarized as following ; For ITB(Improved Ternary Blend)mixture was that setting time proved to be accelerated, and adiabatic temperature rises were low. The use of ITB resulted in an increase of initial compressive strength.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.309-312
• /
• 2004

The hydraulic structure of the hydroelectric power plant such as aqueduct tunnels and the drainage canal became old. Therefore, because the concrete surface of the aqueduct tunnel has received severe damage by wear-out and the crack etc the repair is demanded. This research examined the applicability of the repair mortar which mixed the fly ash and an artificial aggregate by using the very high early strength cement. As a result, good Quality repair mortar which satisfied the demand performance more than self-flow 270mm and compressive strength $50N/mm^2$ (age of 28days) adjusting of water cement ratio by using the MTX cement be able to be manufactured.

• 한국건축시공학회지
• /
• 제6권3호
• /
• pp.99-105
• /
• 2006

In this paper, the estimation of compressive strength of concrete incorporating fly ash subjected to high temperature is discussed. Ordinary Portland cement and fly ash cement(30% of fly ash) were used, respectively. Water to binder ration ranging from 30% to 60% and curing temperature ranging from $20^{\circ}C{\sim}65^{\circ}C$ were also adopted for the experimental parameters. According to results, at the high temperature, FAC had higher strength development at early age than OPC concrete and it kept its high strength development at later age due to accelerated pozzolanic reaction subjected to high temperature. For strength estimation, Logistic model based on maturity equation and Carino model based on equivalent age were applied to verify the availability of estimation model. It shows that fair agreements between calculated values and measured values were obtained evaluating compressive strength with logistic curve. The application of logistic model at high temperature had remarkable deviations in the same maturity. Whereas, the application of Carino model showed good agreements between calculated values and measured ones regardless of type of cement and W/B. However, some correction factors should be considered to enhance the accuracy of strength estimation of concrete.

• 한국환경과학회지
• /
• 제16권3호
• /
• pp.347-355
• /
• 2007

In this paper, estimation of the compressive strength of the concrete incorporating blast furnace slag subjected to high temperature was discussed. Ordinary Portland cement and blast furnace slag cement (BSC;30% of blast furnace slag) were used, respectively. Water to binder ratio ranging from 30% to 60% and curing temperature ranging from $20^{\circ}C{\sim}65^{\circ}C$ were also chosen for the experimental parameters, respectively. At the high temperature, BSC had higher strength development at early age than OPC concrete and it kept its high strength development at later age due to accelerated latent hydration reaction subjected to high temperature. For the strength estimation, the Logistic model based on maturity equation and the Carino model based on equivalent age were applied to verify the availability of estimation model. It was found that fair agreements between calculated values and measured values were obtained evaluating compressive strength with logistic curve. The application of logistic model at high temperature had remarkable deviations in the same maturity. Whereas, the application of Carino model showed good agreements between calculated values and measured ones regardless of type of cement and W/B. However, some correction factors should be considered to enhance the accuracy of strength estimation of concrete.

• 한국건설순환자원학회논문집
• /
• 제11권2호
• /
• pp.105-111
• /
• 2023

본 연구에서는 초기 재령에서 NSH(Non-sintered Hwangto) 치환율에 따른 고강도 콘크리트의 역학적 특성을 평가하였다. NSH의 치환율은 15 % 및 30 %로 설정했다. 평가 항목은 압축강도와 UPV(Ultrasonic pulse velocity)로 설정하였으며, 최종적으로 UPV분석을 통해 압축강도 예측 방정식을 제안하였다. 압축강도와 UPV에서는 NSH 치환율이 증가할수록 낮은 강도 및 UPV를 보였다. 또한 압축강도와 UPV의 상관관계 분석 결과, 상관계수(R2)는 NC33(Normal concrete)은 0.99, NSHC(Non-sintered Hwangto Concrete)33-15는 0.97, 그리고 NSHC33-30은 0.94로 높은 상관관계를 나타냈다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.309-314
• /
• 1998

The moisture diffusion and self-desiccation cause the differential drying shrinkage and autogenous shrinkage at early ages, respecitvely. Thus total shrinkage strain includes the differential drying shrinkage and self-desiccation shrinkage. Thus in this study the shrinkage strain was measured at various positions in the exposed concrete and in the sealed concrete the self-desiccation shrinkage was measured. In low-strength concrete, the differential drying shrinkage increases very rapidly, but self-desiccation shrinkage is very small. But high-strength concrete shows the reverse result. And the analytical results for differential drying shrinkage were in good agreement with the test results.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 봄 학술발표회 논문집
• /
• pp.99-105
• /
• 1993

The purpose of this fundamental study is to investigate the mechanism of high strength concrete using the high calcium sulfate cement from a point of view in cement hydration and micro structure. As a results, it was found that the internal pores of concrete are decreased by using the high calcium sulfate cement, because the hydrates of Ettringite which is densified in structure is much formed in early ages at steam curing. In addition to the ettringite needs the 32 times of free water formed mixing water for hydration. This effect are not only decreased the water to cement ratio and also increase to comp, strength of concrete. It was conclude that these above the two facts are the main mechanism of high strength concrete using high calcium sulfate cement.

• 한국세라믹학회지
• /
• 제37권5호
• /
• pp.438-443
• /
• 2000

This dissertation is focused on the study over the improvement for the early strength of belite-rich cement(BRC). For this purpose, the initial hydration behaviors according to addition of different calcium sulfate types were evaluated. From the observations by XRD, DSC and SEM, the BRC II and III with the addition of natural anhydrate and flue gas desulphurization(FGD) gypsum, respectively, formed much ettringite after 7 days more than the BRC I with the addition of chemical gypsum. The compressive strength of the BRC II and III developed outstandingly due to the formation of calcium aluminate hydrate within pores of hardened BRC paste. Especially, in the case of BRC III adding FGD with low impurities, the early as well as long term compressive strengths were shown very high, compared with other specimens.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.221-222
• /
• 2012

This study is to high early concrete development which reveals 14 MPa within 12 hours in order to reduce the mold time of dismantlement and not do the steam curing of the precast concrete product. About (40~50) min could shorten the final setting time if the coagulation test result cement amount 100 kg/m3 was increased. In the case of the compressive strength, it was exposed to be satisfied the target value with the cement amount 500 kg/m3 combination according to the hardening accelerator addition.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.129-130
• /
• 2021

In order to solve the problem of low early-age compressive strength of high volume fly ash concrete. This paper studies the effect of 2% sodium sulfate (Na₂SO₄) as a chemical activator on the paste with 40% fly ash content and a water-binder ratio of 0.30. The results indicate that the addition of Na₂SO₄ can effectively improve the early-age compressive strength of the fly ash-cement system, and the strength improvement rate on the first day reached nearly 70%. In addition, calorimetric analysis reveals that the incorporation of Na₂SO₄ promotes the early hydration of cement and fly ash, increases the cumulative hydration heat and delays the heat peak of the aluminum phase.