• Journal of the Korean Society of Tobacco Science
• /
• v.20 no.1
• /
• pp.87-94
• /
• 1998

After we made the computer source code with mathematical model of Muramatsu et al. that was expressed by the set of simultaneous first-order ordinary differential equations in evaporation-pyrolysis zone of cigarette, we simulated the distribution profiles of temperature and density of flue-cured tobacco. Those equations were solved numerically with the Runge-Kutta-Gill algorithm assuming step size of 0.025mm by Muramatsu at at,, but in this study the advanced algorithm of Runge-Kutta 4th Order assuming step size of 0.0005mm. The initial conditions and physical parameters of Muramatsu et at. were used for solving them. The calculated values corresponded well with results of Muramatsu et al., especially the gradient of the temperature profile increased with smoldering speed and the thickness of the evaporation-pyrolysis zone decreased with increasing of smoldering speed. On the other hand, the temperature gradient decreased with increasing of the effective thermal-conductivity value and the thickness of the evaporation-pyrolysis zone increased with the effective thermal-conductivity value.

• Journal of ILASS-Korea
• /
• v.21 no.1
• /
• pp.53-57
• /
• 2016

The present study aims to experimentally investigate the evaporative heat transfer characteristics of Oxi-nitriding SPCC surface. Moreover, the heat transfer coefficient was examined with respect to surface temperature during droplet evaporation. In fact, the nitriding surface showed significant enhancement for anticorrosion performance compared to bare SPCC surface but the thermal resistance also increased due to the formation of compound layer. From the experimental results, the evaporative behavior of sessile droplet on nitriding surface showed similar tendency with the bare surface. Total evaporation time of sessile droplet on the nitriding surface was delayed less than 5%. The difference in heat transfer coefficient increased with the surface temperature, and the maximum difference was estimated to be around 11% at $80^{\circ}C$ surface. Thus, this nitriding surface treatment method could be useful for seawater heat exchanger industries.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.851-856
• /
• 1996

Copper Phthalocyanine (CuPc) thin films were fabricated on the silicon wafers by plasma activated evaporation method and structural analysis were carried out with various spectroscopies. The CuPc films had dense and smooth morphology and they also showed good mechanical properties and chemical resistance. The main molecular structure of the CuPc, which is the conjugated aromatic heterocyclic ring structure, was maintained even in the plasma process. However, metal-ligand (Cu-N) bands were deformed by the plasma process and the structure became amorphous especially at higher process pressures. Oxygen impurities were incorporated in the film and carboxyl functional groups were formed at the peripheral benzene ring. The structure and morphology of the films were dependent on the process pressure but relatively irrespective of the RF power.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.1
• /
• pp.25-30
• /
• 1991

The evaporation characteristics of Ag, Al, Au, Cr. Cu, In, Mg, Mn, Pb, Pd, Si, SiO, Sn, Ti and Zn with the various resistive heating sources have been studied. The employed sources are refractory metal (Mo, Ta and W) boats, W-wire, ceramic (usually Al2O3)-coated and -barriered refractory metal boats, and special boats such as baffled boats and intermetallic boats (nitride compound and graphite). We investigated the melting mode, evaporation rate at a specific power, and lifetime of the sources. A special boat holder is also discussed which is needed to cool the sources at a large heat capacity.

• Journal of Powder Materials
• /
• v.17 no.4
• /
• pp.270-275
• /
• 2010

Ethylene glycol-based Cu nanofluids were prepared by pulsed wire evaporation (PWE) method. The structural properties of Cu nanoparticles were studied by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). The average diameter and Brunauer Emmett Teller (BET) surface area of Cu nanoparticles were about 100 nm and $7.46\;m^2/g$, respectively. The thermal conductivity and viscosity of copper nanofluid were measured as functions of Cu concentration and temperature. As the volume fraction of Cu nanoparticles increased, both the enhanced ratios of thermal conductivity and viscosity of Cu nanofluids increased. As the temperature increased, the enhanced ratio of thermal conductivity increased, but that ratio of viscosity decreased.

• Journal of Power System Engineering
• /
• v.3 no.3
• /
• pp.36-43
• /
• 1999

Many of thermodynamic-based diesel combustion simulations incorporated a model of fuel spray which attempts to describe how the spray develops according to time. Because the spray geometry is an essential aspect of the fuel-air mixing process, it is necessary to be calculated quantitatively for the purpose of heat release and emission analysis. In this paper, we proposed the calculating method of non-evaporation spray behaviors by injection rate shapes under actual operating conditions of diesel engine. We confirmed the utility of this calculating model as the calculated results were compared with the measured results. This calculating program can be applied usefully to study on the diesel spray behavior.

• Journal of the Korean Society of Safety
• /
• v.20 no.1 s.69
• /
• pp.68-74
• /
• 2005

The objective of the present work is to examine the evaporation shape of deposited droplet on the hot surface. this paper performed the experiments as following conditions: (a) the surface temperature is within the range between $80^{\circ}C$ and $95^{\circ}C$ in the conduction and radiation, (b) droplet diameter is 3.0mm. The results are as follows; while droplet evaporates, droplet's radius is kept changelessly to $70\%$ evaporation time and droplet's shape is kept changelessly after. In case use Constant radius model, about $10\%$ is appearing high than value that time-averaged heat flux applies Inverse heat conduction.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1995.05a
• /
• pp.41-44
• /
• 1995

The electrochromic WO$_3$ thin films were prepared by using an electron - beam evaporation technique. The influence of the electron - beam evaporation conditions. especially the vacuum pressure, and resistance of ITO substrate on the structural and electrochromic properties of the investigated film was presented. This films showed electrochromic behavior in an aqueous electrolyte of 1 M H$_2$SO$_4$. Among these WO$_3$ thin films, films prepared at a vacuum pressure of 10$^{-4}$ mbar were found to be most stable in terms of cycling durability. The chemical stability of film against dissolution in the aqueous solution was also shown to depend on the quantity of water in the film.

• Journal of ILASS-Korea
• /
• v.2 no.2
• /
• pp.24-34
• /
• 1997

This paper describes the investigation of combustion characteristics of gasoline-methanol blend in constant volume combustion chamber. A constant volume combustion chamber was used to elucidate a basic combustion characteristics and the premixer was installed to control temperature and equivalence ratio. And the maximum pressure, combustion duration and flame propagation according to the evaporation rate were measured to determine the optimal temperature range for evaporating a blend fuel. These experimental results indicate that the combustion characteristics such as combustion chamber pressure and combustion were deteriorated by decreasing surrounding temperature of fuel. These experimental results indicate that the combustion characteristics such as combustion chamber pressure and combustion were deter orated by decreasing surrounding temperature of fuel injected. It was also found that the overall gasification process for methanol blend fuel was influenced by a combustion chamber temperature rather than a premixer temperature.

• Journal of the Korean Solar Energy Society
• /
• v.22 no.2
• /
• pp.11-17
• /
• 2002

This paper is concerned with the development of a new method for making, separating ice and storage floated ice by installing an evaporation plate at under-water within a storage tank. In a conventional harvest-type ice storage system, a tank saves ice by separating an ice from an installed evaporation plate, which is located above an ice storage tank as an ice storage system. Developed new harvest-type method shows good heat transfer efficiency than a convectional method. It is because the evaporation panel is directly contacted with water in a storage tank. Also, at a conventional system a circulating pump, a circulating water distributor and a piping are installed, however these components are not necessary in a new method. In this study ice storage systems are experimentally investigated to study the charge and discharge of thermal energy. The results show the applicable possibility and performance enhancement of a new type.