• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.82-82
• /
• 1993

• Journal of the Korean Vacuum Society
• /
• v.16 no.3
• /
• pp.181-186
• /
• 2007

We have investigated and analyzed the effects of the evaporation rate of MgO films on the MgO properties and the discharge characteristics of a plasma display panel(PDP). The MgO properties such as the crystal orientation, the surface roughness, the film structure, and cathode-luminescence (CL) spectra were inspected using XRD (X-ray diffraction), AFM(atomic force microscopy). And the discharging characteristics of the PDP such as the firing voltage, discharging current, and luminescence were measured using a vacuum chamber with oscilloscope (TDS 540C), current probe (TCP-312A), color meter (CS-100A) and etc. From the experiments results we confirmed the optimum evaporation rate at $5{\AA}/sec$, the MgO properties were shown to be strongly dependent on the evaporation rate, and the MgO properties had an effecton the optical and electrical characteristics. In other words, if the evaporation rates increase than $5{\AA}/sec$, the intensity of (200) orientation and cathode-luminescence (CL) spectra reduce, and the firing vlotage was increased. So the luminuous efficiency grows worse.

• Journal of Power System Engineering
• /
• v.16 no.2
• /
• pp.24-29
• /
• 2012

In this paper, an analysis on performance and exergy of R404A refrigeration system using R744 secondary refrigerant was performed numerically to optimize the design for the operating parameters. The operating parameters considered in this study include subcooling and superheating degree, internal heat exchanger and compression efficiency, evaporation and condensation temperature in the R404A refrigeration cycle and temperature difference of cascade heat exchanger. The main results are summarized as follows : The COP(coefficient of performance) of R404A refrigeration system increases with increasing evaporation temperature. The evaporation capacity of R744 as secondary refrigerant increases with the increase in evaporation pressure of R744 secondary refrigeration. And the enthalpy in the evaporator outlet of R744 increases with the increasing evaporation pressure of R744 secondary refrigeration. Therefore, it is important to analysis for the relationship between COP of R404A refrigeration system and refrigeration capacity of R744. As cascade evaporation temperature increase, the exergy loss of condenser and compressor using R404A is the largest among all components. Therefore, the exergy loss in the condenser and compressor using R404A must be decreased to enhance the COP of R404A refrigeration system with R744 secondary refrigerant.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.312-312
• /
• 2013

GaN based light emitting diodes (LEDs) are important devices that are being used extensively in our daily life. For example, these devices are used in traffic light lamps, outdoor full-color displays and backlight of liquid crystal display panels. To realize high-brightness GaN based LEDs for solid-state lighting applications, the development of p-type ohmic electrodes that have low contact resistivity, high optical transmittance and high refractive index is essential. To this effect, indiumtin oxide (ITO) have been investigated for LEDs. Among the transparent electrodes for LEDs, ITO has been one of the promising electrodes on p-GaN layers owing to its excellent properties in optical, electrical conductivity, substrate adhesion, hardness, and chemical inertness. Sputtering and e-beam evaporation techniques are the most commonly used deposition methods. Commonly, ITO films on p-GaN by sputtering have better transmittance and resistivity than ITO films on p-GaN by e-bam evaporation. However, ITO films on p-GaN by sputtering have higher specific contact resistance, it has been demonstrated that this is due to possible plasma damage on the p-GaN in the sputtering process. In this paper, we have investigated the advanced sputtering using plasma damage-free p-electrode. Prepared the ITO films on the GaN based LEDs by e-beam evaporation, normal sputtering and advanced sputtering. The ITO films on GaN based LEDs by sputtering showed better transmittance and sheets resistance than ITO films on the GaN based LEDs by e-beam evaporation. Finally, fabricated of GaN based LEDs by using advanced sputtering. And compared the electrical properties (measurement by using C-TLM) and structural properties (HR-TEM and FE-SEM) of ITO films on GaN based LEDs produced by e-beam evaporation, normal sputtering and advanced sputtering. As a result, It is expected to form plasma damage free-electrode, and better light output power and break down voltage than LEDs by e-beam evaporation and normal sputter.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.1
• /
• pp.64-68
• /
• 1991

In this paper, to percuss whether fish oil can substitute for marine fuel oil, the characteristics on the evaporation and ignition of 3 fish oils, Sardine oil, File fish oil and Alaska pollac oil, were investigated experimentally by suspending single fish oil droplel in hot atmosphere, and experiments on methanol and light oil were also carried out to compare the characteristics. The results abtained are summarized as follow; 1) Evaporation and ignition phenomena on the methanol and light oil by the present experimental method agreeded with the results of the earlier investigation. 2) The characteristic on evaporation and ignition of all 3 fish oils took the same pattern; in late stage of evaporation at atmospheric Temperature 55$0^{\circ}C$ droplet rapidly expanded and contracted, and then remained solid corbide, but in case of $650^{\circ}C$ rapidly expanded and ignitied, and then completly burned non-remained solid carbide. 3) As fish oil mixed with light oil (50% weight), in beginning stage of evaporation droplet depended on the characteristics of light oil, but in end stage depended on fish oil. 4) Ignition temperature of fish oil droplets was about 47$0^{\circ}C$, higher than about 25$0^{\circ}C$ of light oil, but atmospheric temperature to ignite droplet was about $650^{\circ}C$, lower than about 75$0^{\circ}C$ of light oil.

• Journal of the Korean Institute of Gas
• /
• v.18 no.6
• /
• pp.1-6
• /
• 2014

This study is based on a investigation regarding the evaporation rate of a volatile liquid(methanol, tetrahydrofuran, xylene) according to changes of the temperature and wind. The weight of a volatile liquid was standardized to 24 g and the mixture was formed with the same weight ratio. In order to discover about the effect of the wind velocity, small fan was installed at 10 cm above the entrance and 30 cm away in the direction of the cylinder. The effect of the wind velocity was tested at 0 m/s, 1.63 m/s, 2.03 m/s respectively and the effect of the temperature on the volatile liquid was experimented at the temperature of $21^{\circ}C$, $32^{\circ}C$, $52^{\circ}C$ in the constant temperature water base. As a result, in case of Xylene, the evaporation rate of the tetrahydrofuran and methanol showed 1.4 mg/min, 19.8 mg/min and 10.2 mg/min respectively. Also, the effect of the evaporation rate on the temperature of the volatile liquid and on the velocity of wind was shown to be very sensitive. At the same time, the evaporation rate of the mixture showed large difference compared to that of the single volatile liquid.

• Journal of The Korean Association For Science Education
• /
• v.13 no.1
• /
• pp.92-99
• /
• 1993

The purpose of this study was to investigate and analyze the conception of elementary school students on evaporation and condensation, and then to verify the types of the conception. Forty-eight children from six elementary schools were sampled by stratified random sampling in Seoul and other provinces. They responded to the questionaire and the interview. This study was carried out according to the process of the basic study, the preliminary study, and the main study. The materials collected were classified and analyzed according to the types of children's ideas. The findings of this study were as follows. 1. The vocabulary used to describe the evaporation phenomena varied according to the situations, and the scientific term "evaporation" was more frequently used by the older groups. 2. Most children answered that the last location of water were air/sky/cloud. Air/cloud which represents the scientific conception of the location of water were mentioned by children of all ages. The higher the grade of the children were, the more scientific conception the children mentioned, however. 3. Most children referred to the heat as the factor of evaporation. Wind, on the other hand was mentioned by less than 10% of lower graders, and by about 30% of higher graders. 4. The result of asking children whether they thought it was possible to get the evaporated water back showed that about 70% of lower graders denied the possibility of the water being reversible. About 60% of higher graders. however, recognized that the water will be returned as rain or condensation. This increase may be associated with formal teaching of water cycle. 5. In the ideas of evaporation and condensation, some of the children have supernatural ideas and animism, which are most younger chilren's characteristics.

• Water for future
• /
• v.18 no.3
• /
• pp.243-251
• /
• 1985

The distributions of the copper plated(small) pan evaporation in both space and time are analysed with the data observed, and the lake and the potential evaportranspiration are estimated from the climatological data. These value are compared with each other and to the precipitation for deducing the seasonal amounts and variations of water budgets in the selected basins and regions. The meteorological factor which is closely associated with the small pan evaporation are hardly recognizable when they are used as the monthly values. The relationships among the small pan, the Class A pan and the lake evaporation are well correlated with each other with correlation coefficient of above 0.90, so it may be possible to derve other evaporations from knowing one evaporation. The ratio of the Class A pan and the lake evaporation to the small pan evaportion in annual are about 73% and 55%, repectively, except the mountaineous area where the values are about 10% less than those. The evapotranspiration reach about 40∼60% of the annumal precipitation, but in May and October two values are nearly same. The frequencies of the monthly evaportion in class intervals in the regions are also provided.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.4
• /
• pp.3545-3554
• /
• 1974

The objective of this study was to investigate the characteristics of the evaporation rate, the plastic shrinkage and the compressive strength of concrete exposed to a rapid evaporation environment immediately after casting. Drying of concrete were conducted under a controlled chamber in which the temperature was mainfoimed at 30 ${\pm}$1$^{\circ}C$, the relative humidity 22 ${\pm}$1 percent, and the wind velocity 7 ${\pm}$1 m/sec. The compressive strength of concrete was tested after 28 days of standard curing. The results obtained are as follows: 1. The evaporation rate was the highest at the very beginning, was decreased as the drying progresses, and was kept almost constant after 6 hours. 2. The shrinkage of concrete was changed in three different rates for the concrete mixture having its slump vallue between 3.0cm and 7.5cm. 3. The plastic shrinkage was ended within 5 or 6 hours after casting, regardless of the water cement ratio. 4. The shrinkage was increased within the limit of slump values between 3.0cm and 7.5cm as the water-cement ratio was increased. 5. The evaporation was kept on even after the plastic shrinkage was ended. 6. Within the limit of good workability (slump value between 4.5cm and 7.5cm), the compressive strength of concrete was increased when the shrinkage rate was slow but it was decreased when the rate was rapid 7. From the result of this study it is recommended that (1) the water-cement ratio should be less as long as the workability of concrete is allowable; (2) the evaporation should be prevented at least for 4 hours after casting concrete.

• Korean Journal of Materials Research
• /
• v.12 no.9
• /
• pp.712-717
• /
• 2002

New wet chemical method so called precipitation-evaporation method was suggested for preparing spinel structure lithium manganese oxide ($LiMn_2$$O_4$) for Li ion secondary battery. Using precipitation-evaporation method, $LiMn_2$$O_4$ cathode materials suitable for Li ion secondary batteries can be synthesized. Single spinel phase $LiMn_2$$O_4$ powder was synthesized at lower temperature compared to that of prepared by solid-state method. $LiMn_2$$O_4$ powder prepared by precipitation-evaporation method showed uniform, small size and well defined crystallinity particles. Li ion secondary battery using $LiMn_2$$O_4$ as cathode materials prepared by precipitation-evaporation method and calcined at $800^{\circ}C$ showed discharge capacity of 106.03mAh/g and discharge capacity of 95.60mAh/g at 10th cycle. Although Li ion secondary battery showed somewhat smaller initial capacity but good cyclic ability. It is suggested that electro-chemical properties can be improved by controlling particle characteristics by particle morphology modification during calcination and optimizing Li ion secondary battery assembly conditions.