• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.511-521
• /
• 2014

This study proposes an electric vehicle (EV) smart panel board and its control method on the basis of charging scheduling. The proposed system consists of batteries, a three-phase battery charger, three single-phase inverters, transfer switches for electric power distribution, and a controller. The three-phase battery charger usually charges the batteries at midnight when electric rates are cheap and in light load. When the electric power consumption of the EV standard chargers connected to one phase of the power line is relatively large or when a blackout occurs, the electric power stored in the battery is supplied by discharging through the inverters to the EV standard chargers. As a result, the value of peak load and the charging electric power quantity supplied from a utility grid are reduced, and the current unbalance is improved. The usefulness of the proposed system is confirmed through simulations, experiments, and case studies.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.274-277
• /
• 1995

Recent environmental pollutions have intensified the need to develop zero emission vehicles. The most effect method of such solutions is EV. EV is high energy efficiency, easy to maintain, repair and is possible to make high performance control. However, because energy density of batteries is constrained and the distance covered one charge is short range. Also because EV has disadvantage of poor accelation ability, development of high performance battery is required for large scale use of EV. EV charger analogous to gas apparatus must also be developed immediately. Charger is discriminate between on-vehicle type and off-vehicle type. As off-vehicle type is able to charge fast and safe, inductive charging is considered. This paper aims to develope off-vehicle inductive charging system. Therefore, it achieved power factor correction converter, high frequency DC/AC inverter control algorithm development which gives proof validity through simulation and formulated the basic concept of high frequency transformer design for inductive charging.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.98-105
• /
• 2014

As environmentally friendly energy takes center stage, interests for Electric Vehicles/Plug in Hybrid Electric Vehicles (EVs/PHEVs) are getting increase. With this trend, there is no doubt EVs will take large portion to penetrations of total cars. Therefore, accurate EV modeling is required. Battery is one of the main components with the power system view of aspect. Hence, in this paper, reviews and discussions of some types of batteries for EV are contained by considering energy density and weight of the batteries. In addition, simulations of Li-Ion battery are accomplished with various variables such as temperature, capacity fading and charge/discharge current. It is confirmed that temperature is the main factor of capacity fading. Validation of the modeled battery is also conducted by comparing it with commercialized battery.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.2171-2172
• /
• 2011

Recently, while interests on supply of electric vehicles have increased there still are insufficient charging facilities. As a solution to this matter, using electric power grids that constantly retain about 30~50[%] residual power is being considered. Therefore proposed in this paper railway, is a method to establish a charging infrastructure to utilize railway DC power grids. In addition we designed a high-speed DC charging system, and simulated improvements of the charging structure's charging efficiency according to remaining capacity of batteries.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.4
• /
• pp.263-270
• /
• 2021

In this study, we proposed the necessity of reusing the battery industry after domestic use, preparing legal arrangements by step for recycling, clarifying responsible materials by processing stage, and establishing infrastructure and screening diagnostic rating system. The purpose of this study is to establish a life cycle integrated management system for electric vehicle batteries and to find suitable ways for improving the lifespan of electric vehicle batteries, reuse, and recycling in stages to avoid other environmental pollution problems due to batteries after using electric vehicles used to reduce environmental pollution due to climate change.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1141-1142
• /
• 2011

An electrical vehicle (EV) is a huge issue in the automotive industry. The EV have many electrical units: electric motors, batteries, converters, ets. The DC power distribution system (PDS) is essential for the EV. The DC PDS offers many advantages. However, multiple loads in the DC PDS may affect the severe instability on the DC bus voltage. Therefore, a voltage bus conditioner (VBC) may use the DC PDS. The VBC is used to mitigate the voltage transient on the bus. In this paper, sliding mode controller (SMC) is designed for the VBC of DC PDS in the EV. The simulation results by PISM simulation package are presented for validating the proposed control technique.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.4
• /
• pp.218-220
• /
• 1999

The performance of the Electric Vehicle and Hybrid Electric Vehicle depends on that of the battery pack composed of series connected batteries. And thermal property is one of the main factors which decide the performance of the battery pack. So heat generation rate from the battery under the various driving mode must be measured as precise as possible because thermal characteristics of the battery affect the driving performance and battery pack's life cycle. Besides, to design and develop the battery thermal management system for the EV and HEV, the measurements of the thermal properties of the batteries are needed. However, the established calorimeter is not adequate to test an EV's battery because its cavity is too small to accommodate the EV's battery. Therefore we developed the calorimeter to test the thermal property of the EV's battery. Its cavity size is 120mm long, 75mm wide and 200mm high. The calorimeter is calibrated by the dummy cell which generates the heat rate from zero to 200W. The measuring accuracy of the calorimeter is within $2\%$ and its voltage stability is 2.5mV in the constant temperature bath.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.465-470
• /
• 1999

This paper presents a design method of driving system for EV(Electric Vehicle). EV driving system consist of batteries, battery interface system and inverter. The power control circuit of the driving system is simple, since only one PWM(Pulse Width Modulation) inverter is used. These test spectrums and waveforms can be used to determine the filter component ratings as well as to compute the harmonics injected into the source. The hybrid control strategy which can reduced harmonic components. The analysis results indicate that the required capacity of the condenser can be reduced with LC filter. In this paper, the design and implementation of the proposed systems are described and some experimental results are given to show the performance of this driving system. The control strategy of the system to available inverter's power and motor's power and torque is discussed.

• International Journal of Reliability and Applications
• /
• v.12 no.2
• /
• pp.123-129
• /
• 2011

Due to restriction of vehicle emissions and high demand for fossil fuels nowadays, car manufacturers around the world are looking into alternative ways in introducing new car model that would vastly captured the market. Thus, Electric Vehicle (EV) has been further developed to take the advantage of the current global issues on price of fossil fuels and impact on the environment. Since car battery plays the crucial role on the overall performance of EV, many researchers have been working on improving the component. This paper focused on the reliability of EV battery which involves recognizing failure types, testing method and life prediction method. By focusing on these elements, the reliability feature being identified and as a result the batteries life will be prolonged.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.341-348
• /
• 2019

This paper reports the microstructure and electrochemical properties of Si-Al-Fe ternary amorphous alloys prepared by rapid solidification as an anode for lithium secondary batteries. The microstructure was analyzed using XRD and HR-TEM with EDS mapping. In accordance with DSC analysis, annealing was performed to crystallize the active nano-Si in the amorphous alloy. Thus, nano-Si forms (~80 nm) embedded in the matrix alloy, such as $Fe_2Al_3Si_3$, $FeSi_2$, and $Fe_{0.42}Si_{2.67}$, were successfully synthesized. The electrode based on the Si-Al-Fe ternary alloy delivered an initial discharge capacity of approximately $700mAh^{g-1}$, and exhibited a high Coulombic efficiency of 99.0~99.6% from the $2^{nd}$ to $70^{th}$ cycles.