• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.510-513
• /
• 2018

Recently, EMC (electromagnetic compatibility) becomes very important, which demands the measurement of EMI (electromagnetic interference) in the chip level. NFS (near-field scanning) systems defined in IEC 61967 and IEC 62508 are typical methods to analyze EMI in the chip level. As chips becomes faster, frequency measurement of NFS system should become wideband, but it degrades SNR (singal-to-noise ratio) of the NFP (near-field probe). This paper surveys SNR enhancement technologies of the NFS while maintaining wideband characteristics.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.211-214
• /
• 2007

Development of IT and electronics industries has make our life more convenient, yet at the cost of radio communication noise, malfunctioning of electronic appliance and risks against human health all resulting from EMI. Many states are tightening their EMI (Electro Magnetic Interference) regulations around the world and the EMI regulatory measures are likely to increase in terms of targets and types. Against this backdrop, this paper aims to introduce fundamental and adequate EMI countermeasures encompassing product production cycle from design to production stage.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.43-50
• /
• 2003

전자산업과 전파통신기술이 고도로 발전함에 따른 전파 이용의 증대로 인해 전자파환경 EMI/EMS이 사회적 문제를 야기하고 있다. 이에 따라, CISPR(Comite Internationale Special des Perturbations Radioelectrique), FCC (Federal Communications Commissions) ANSI (American National Standards Institute)등의 기구는 EMI/EMC 대책을 위해 전파환경의 규정을 제정하고 있다. 또한 EMI/EMC 측정을 위한 전파무향실(anechoic chamber)용 전파흡수체는 20 dB 이상의 전파흡수능이 요구된다. 종래의 EMI 측정 주파수 범위는 30 MHz～l,000 MHz 이었으나 1998년 11월, CISPR11은 1 GHz~18 GHz를 추가하는 안을 받아들였다. 본고는 새로운 형태의 다층형 페라이트 전파흡수체를 제안하고 등가재료정수법을 사용하여 광대역 설계를 시도한 것이다.

• Journal of the Korea Convergence Society
• /
• v.7 no.6
• /
• pp.23-28
• /
• 2016

In this study, an investigation study on EMC(Electromagnetic Compatibility) is presented for power converter circuit. A DC-DC power converter circuit using LT3652 chip is designed and fabricated. The simulation results using ANSYS SIwave for far field radiation and unwanted emissions are presented. To minimize the unwanted emissions, we design a optimized circuit by using capacitors and ground posts. The conducted and radiation emissions are measured in the EMC test chamber based on standardized testing procedures of CISPR 22. The measured EMI emission values for a power converter circuit are presented and compared with the original circuit. The results show that the unwanted emissions from the circuit are tremendously diminished due to the applied EMI reduction techniques. The results proposed here can be usefully applied on designing power converter modules.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.619-625
• /
• 2013

Switched mode power supplies (SMPS) are power electronic circuits extensively used in a wide range of applications. High frequency switching operation of SMPS causes electromagnetic emissions and has the potential to interfere with system operation, which in turn has an impact on system performance. This makes electromagnetic compatibility (EMC) an important concern. In this paper, a new and simple spread spectrum technique is proposed by modulating chaotic pulse position modulation (CPPM) and pulse width modulation (PWM). The resulting CPWM is implemented to reduce the conducted EMI in SMPS. The proposed method is found to be effective in reducing conduction EMI. The effectiveness and simplicity of the proposed method on spreading those dominating frequencies is compared to the EMI mitigation technique using an external chaotic generator. Finally, the levels of conductive EMI with standard PWM, CPWM with an external chaos generator and the proposed method are experimentally verified to comply with the CISPR 22A regulations. The results confirm the effectiveness of the proposed method.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.244-248
• /
• 2001

According to the progress of the electronic industry and radio communication technologies, mankind might enjoy its abundant life. On the other hand, many social problems such as EMI, and unnecessary electromagnetic wave occur due to the increased use of electromagnetic wave. Therefore, the organizations such as CISPR, FCC, ANSI, etc. have provided the standard of electromagnetic wave environment for the countermeasure of the EMC. It had been required that the absorbing ability of an electromagnetic wave absorber is more than 20dB, the bandwidth of which is required through 30 MHz to 1,000 MHz for satisfying the international standard about an anechoic chamber for EMI/EMS measurement. From November of 1998, however, the CISPR11 has accepted the extended frequency band from 1 GHz to 18 GHz additionally in the bandwidth of EMI measurement[1]. In this paper, we proposed a new type absorber satisfying the above requirements and carried out broadband design using the equivalent material constants method. Futhermore, the experiments were carried out over the frequency band from 30 MHz to 2 GHz, and hence, the validity of the proposed design theory was confirmed.

• The Magazine of the IEIE
• /
• v.23 no.5
• /
• pp.61-74
• /
• 1996

• Information and Communications Magazine
• /
• v.15 no.8
• /
• pp.80-87
• /
• 1998

• 전기의세계
• /
• v.38 no.9
• /
• pp.6-6
• /
• 1989

• The Magazine of the IEIE
• /
• v.28 no.2
• /
• pp.23-30
• /
• 2001