• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.551-554
• /
• 2005

In this Paper, a super wide-band EM wave absorber was designed by attaching pyramidal type absorber on a ferrite absorber. The used ferrite absorber was in hemisphere type on a cutting cone-shaped absorber. As a result, the bandwidth has been broadened from 30 MHz to 18 GHz and the total height of the EM Wave absorber is relatively low profile of 14.26 cm.

• Journal of electromagnetic engineering and science
• /
• v.8 no.2
• /
• pp.70-75
• /
• 2008

In this paper, the EM wave absorber was designed and fabricated for countermeasure against EMI from a ceiling of a tollgate in ETC system. We fabricated several samples in different composition ratios of MnZn-ferrite, Carbon, and CPE(Chlorinated Polyethylene). Absorption abilities were simulated in accordance with different thicknesses of the prepared absorbers and changed complex relative permittivity and permeability according to composition ratio. The optimized mixing ratio of MnZn-ferrite, Carbon, and CPE was found as 40:15:45 wt.% by experiments and simulation. Then the EM wave absorber was fabricated and tested using the simulated data. As a result, the developed EM wave absorber has the thickness of 3.3 mm and absorption ability was more than 20 dB in the case of normal incidence and more than 11 dB for the incident angle from 15 to 45 degrees at 5.8 GHz. Therefore, it was confirmed that the newly developed absorber can be used for ETC system.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.415-420
• /
• 2005

To construct an anechoic chamber for EMI test satisfying some international standards, it has been recognized that the absorption characteristics of the EM wave absorber must have more than 20 dB over the frequency band from 30 MHz to 18 GHz. In this paper, an EM wave absorber with super wide-band frequency characteristics was proposed and designed in order to satisfy the above requirements by using the EMCM[1]. As a result, the proposed absorber has absorption characteristics more than 20 dB over the frequency band from 30 MHz to more than 20 GHz.

• Journal of electromagnetic engineering and science
• /
• v.5 no.4
• /
• pp.172-175
• /
• 2005

Sometimes, it is more convenient to use paint-type and spray-type EM wave absorbers than bulk-type or sheet-type. Thus, in this paper, we prepared paint-type and spry-type EM wave absorbers. The proportion of ferrites to paints, particle size of magnetic material, and kinds of paint should be considered to prepare a superior paint-type EM wave absorber. There is no big gap between spray-type and paint-type in EM wave absorption of EM wave absorbers prepared with same composition.

• Journal of Navigation and Port Research
• /
• v.33 no.3
• /
• pp.193-197
• /
• 2009

In this paper, the EM wave absorber was designed and fabricated for improvement of Wireless LAN environment at 2.4 GHz. We fabricated several samples in different composition ratios of Sendust and CPE(Chlorinated Polyethylene). Absorption abilities were simulated in accordance with different thicknesses of the prepared absorbers and changed complex relative permittivity and permeability due to composition ratio. The mixing ratio of Sendust and CPE was searched as 80: 20 wt.% by experiments and simulation Then the EM wave absorber was fabricated and tested using the simulated data. As a result, the EM wave absorber was fabricated based on simulated data. Simulated and measured results agreed well. As a result, the developed EM wave absorber with thickness of 3.25 mm has absorption ability of 19 dB at 2.4 GHz.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.117-120
• /
• 2008

In this paper, we developed the EM wave absorber for eliminating false images in collision-avoidance radar. First of all, we fabricated some samples in different composition ratio of $TiO_2$ and CPE. And the relative permittivities of samples are calculated from S-parameter of samples by using 1-port method. We designed and fabricated the EM wave absorber by using the calculated relative permittivity. As a result, the EM wave absorber with composition of $TiO_2$:CPE=70:30 wt% has thickness of 1.85 mm and absorption ability higher than 20 dB in the frequency range 76-77 GHz.

• Journal of Navigation and Port Research
• /
• v.30 no.9
• /
• pp.763-766
• /
• 2006

In this paper, the EM wave absorbers were designed and fabricated for X -band sensors using Carbon of dielectric material with CPE. The complex relative permittivity of samples is calculated by using measurement results of S-parameter. We simulated the double-layered type EM wave absorber with broad bandwidth using the measured complex relative permittivity by changing the thickness and layer, which was fabricated based on the simulated design The fabricated EM wave absorber consists of 1 mm first layer sheet facing metal with Carbon composition ratio 70 vol. % and 1.5 mm second layer sheet with Carbon composition ratio 60 vol. %. The measured results showed a good agreement to the simulated ones. It is found toot the optimized absorption ability of double-layered type EM wave absorber with thickness of 2.5 mm is higher than 10 dB from 7.8 GHz to 13.3 GHz.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.297-300
• /
• 2006

In this paper, the EM wave absorbers were designed and fabricated for X-band sensors using Carbon of dielectric material with CPE. The complex relative permittivity of samples is calculated by the measured S-parameter data. We simulated the double-layered type EM wave absorber with broad bandwidth using the measured complex relative permittivity by changing the thickness and layer, which was fabricated based on the simulated design. The fabricated EM wave absorber consist of 1mm first layer sheet facing metal with Carbon composition ratio 70 vol% and 1.5 mm second layer sheet with Carbon composition ratio 60 vol%. The comparisons of simulated and measured results are good agreement. As a result, the optimized absorption ability of double-layered type EM wave absorber with thickness of 2.5 mm is higher than 10 dB from 7.8 GHz to 13.3 GHz.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.67-68
• /
• 2005

This thesis is concerned with basic research for development of EM wave absorbers in sheet type for mobile phones. By controlling the sendust ratio, the $Al(OH)_3$ coating, the thickness, the kind of binders, EM wave absorbers were prepared and examined. Centeral frequency shifts toward lower with increasing thickness of the absorber, and absorption ability controlled to adjust Sendust amount. The absorption band of the EM wave absorber coated with $Al(OH)_3$ becomes larger than that of non-coated one. Sendust composite microwave absorbers mixed with CPE were prepared at $70^{\circ}C$ in temperature. The fabricated EM wave absorbers show a reflection coefficient 5.56 dB at 1.8 GHz in thickness of 0.85 mm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.6
• /
• pp.509-515
• /
• 2009

In this paper, we analyzed and evaluated noise suppression characteristic of EM wave absorber. We fabricated several absorber samples in different ratios of Sendust and Amorphous with CPE(Chlorinated Ploy-ethylene) as binder and calculated material constants by measured S-parameter. Then, we confirmed that the noise suppression characteristic of EM wave absorbers using microstrip line. A microstrip line with EM wave absorber placed on its top was used to evaluate the conduction noise suppression. As a result, noise suppression effect show different charateristic by changing relative permeability. Therefore, EM wave absorber using Sendust show excellent characteristic. In particular the maximum power absorption over 90 % in 1.7 GHz to over 6 GHz has obtained when composition of Sendust:CPE=80:20wt.%.