• The Magazine of the IEIE
• /
• v.11 no.5
• /
• pp.69-74
• /
• 1984

• Architectural research
• /
• v.7 no.1
• /
• pp.27-38
• /
• 2005

No specific guidelines are available for computing the bearing strength of connection between steel coupling beam and reinforced concrete shear wall in a hybrid wall system. There were carried out analytical and experimental studies on connection between steel coupling beam and concrete shear wall in a hybrid wall system. The bearing stress at failure in the concrete below the embedded steel coupling beam section is related to the concrete compressive strength and the ratio of the width of the embedded steel coupling beam section to the thickness of the shear walls. Experiments were carried out to determine the factors influencing the bearing strength of the connection between steel coupling beam and reinforced concrete shear wall. The test variables included the reinforcement details that confer a ductile behavior in connection between steel coupling beam and shear wall, i.e., the auxiliary stud bolts attached to the steel beam flanges and the transverse ties at the top and the bottom steel beam flanges. In addition, additional test were conducted to verify the strength equations of the connection between steel coupling beam and reinforced concrete shear wall. The proposed equations in this study were in good agreement with both our test results and other test data from the literature.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.1
• /
• pp.69-76
• /
• 2020

Bridges which are components of road network consume large amounts of resources such as concrete and steel materials, which have large environmental impacts during construction. This causes a great environmental burden. In order to reduce the environmental impact caused by the construction of the bridge, the environmental impact should be reviewed based on reasonable data in the early design stage. The purpose of this study is to provide basic data for LCA-based environmental impact assessment in the process of selecting bridge type in the early design stage. For this purpose, design data for four types of PSC bridges (general PSC girder, IPC girder, e-Beam, DR girder) were collected and LCA was performed to analyze the basic unit value and impact factors of environmental load. The results of the analysis showed that the environmental impact of IPC girder was the smallest, and the environmental impact of e-Beam was 133.7% higher than that of IPC girder. In addition, concrete, reinforcement, PC strand, square timber, sheath pipe, and steel plate were derived as the main factors that generate 98.5% of the overall environmental impact of PSC girder.

• Polymer(Korea)
• /
• v.36 no.3
• /
• pp.393-400
• /
• 2012

The characteristics of indium tin oxide (ITO) thin film deposited on polyethersulfone (PES) film by low temperature E beam has been studied for the flexible photovoltaic devices. It was found that the substrate temperature in the deposition process affected the crystallization behavior of ITO during the post low temperature annealing process. Higher substrate temperature resulted in the increase of crystallinity of annealed ITO. Consequently, the lowering of sheet resistivity and better transmittance were obtained. Crystallization of ITO during the annealing process was facilitated by using oxygen gas in the deposition process and resulted in the enhancement on sheet resistivity and transmittance of ITO. The surface roughness of PES film prohibited the crystallization of ITO during the annealing process and it caused the increase of sheet resistivity and the decrease of transmittance of ITO.

• Food Science and Preservation
• /
• v.17 no.1
• /
• pp.151-159
• /
• 2010

Changes in volatile organic compounds were investigated during storage after electron beam irradiation. Grapes were irradiated at 0.25, 0.5, 0.75, and 1.0 kGy and stored for 1 month at $4^{\circ}C$. Butanol, hexanal, [E]-2-hexenal, hexanol, and 3-methyl-butanol were the major volatile organic compounds of grapes. The types of volatiles in irradiated grapes were similar to those of non-irradiated samples but concentration differed among treatments. Some volatile compounds decreased during storage, whereas others, especially the esters, increased. Concentration of most volatile compounds were higher in pre-stored grapes than in post-stored fruit (thus, during the 30 days after irradiation by e-beam). Consequently, concentration of volatile organic compounds either increased or decreased after e-beam irradiation but these changes did not correlate with irradiation dose.

• Journal of the Korean Vacuum Society
• /
• v.8 no.1
• /
• pp.43-50
• /
• 1999

We have studied the alignment and the lattice quality of hexagonal rings of h-BN films synthesized by ion beam assisted deposition (IBAD) method. Boron was e-beam evaporated at 1.5 $\AA$/sec and nitrogen gas was ionized using end-hall type ion gun at 60, 80, and 100 eV, respectively. Substrate was either not heated or heated at 200, 400, 500, and $800^{\circ}C$, respectively. As nitrogen ion energy increases, c-axes of hexagonal rings tend to align parallel to the substrate, which is explained by larger compressive stress at higher ion energies. Alignment of c-axis increases with temperature and shows maximum around $400^{\circ}C$. The lattice quality of hexagonal rings improves with temperature. Such behaviors can be understood from two counter trends of increasing the atomic mobility and decreasing compressive stress with temperature. Hardness of h-BN films shows the same trend with the alignment of c-axis. Ion beam assisted deposition method seems to be effective for aligning hexagonal rings and optimizing h-BN properties.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.384-384
• /
• 2013

본 연구에서는 e-beam 증착을 이용하여 Al, Mg 단일 금속으로 다층형 Al-Mg 코팅층을 제조하여 특성 분석 및 내식성을 평가하였다. Al-Mg 코팅층은 99.99%의 Al, 99.9%의 Mg grain을 사용하여 E-Beam 가열을 통해 냉연강판 위에 코팅하였다. 증발물질과 기판과의 거리는 48 cm이며, 기판은 세척을 실시한 후 진공 챔버에 장착하고 ~10-5 Torr 까지 진공배기를 실시하였다. 진공챔버가 기본 압력까지 배기되면 아르곤 가스를 주입하고 기판홀더에 800 V의 직류 전압을 인가하여 약 30분간 글로우 방전 청정을 실시하였다. 기판의 청정이 끝나면 아르곤 가스를 차단하고 코팅층의 구성형태에 따라 Al 또는 Mg을 코팅하였다. 다층형 Al-Mg 코팅층은 2층에서 최대 6층까지 제조하였으며 $3{\mu}m$의 두께를 기준으로 Al과 Mg 코팅층의 두께비가 각각 1:1 과 2:1이 되도록 코팅하였다. 6층 이상에서는 코팅층의 두께 제어가 쉽지 않기 때문에 층수는 6층으로 제한하였다.다층형 Al-Mg 코팅층을 주사전자현미경으로 관찰한 결과, Al-Mg 코팅층간의 계면을 관찰할 수 있었다. 또한 글로우방전분광기로 Al-Mg 코팅층을 관찰한 결과, Al과 Mg 코팅층이 균일한 다층 구조를 형성하고 있는 것을 확인할 수 있었다. 다층의 Al-Mg가 코팅된 강판을 염수분무시험을 통해서 내부식 특성을 확인하였다. Al-Mg 코팅 강판의 염수분무시험 결과, Al-Mg 코팅층의 층수가 증가할 수록 내부식 특성이 향상되는 것을 확인할 수 있었으며, 이러한 현상은 Al-Mg 코팅층이 다층으로 형성되어 있어 부식 생성물을 효과적으로 차단하여 강판의 부식을 방지한 것으로 판단된다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.1
• /
• pp.70-75
• /
• 1997

An improved technique based upon an electron beam evaporation system has been developed to prepare cubic thin films In crystalline semiconductors. Zinc blonde CdSe epilayers were grown on GaAs(100) substrate by an e-beam evaporation method. The lattice parameter obtained from (400) reflection is $6.077\AA$, which is in excellent agreement with the value reported in the literature for zinc blonde CdSe. The orientation of the as-grown CdSe epilayer is determined by electron channeling patterns. The crystallinity of epitaxial CdSe layers were investigated on the double crystal X-ray rocking curve. The carrier concentration and mobility of epilayers deduced by Hall effect measurement are about $10^{18}{\textrm}{cm}^{-3}$, $10^2\textrm{cm}^2/V{\cdot}sec$ at room temperature, respectively. The photocurrent spectrum peak of the epilayer at 30 K exhibits a sharp change at 1.746 eV due to the free exciton of cubic CdSe.

• Nuclear Engineering and Technology
• /
• v.19 no.2
• /
• pp.115-121
• /
• 1987

A high voltage stabilization system for the SNU 1.5MV Tandem Van do Graaff accelerator was set up and its operational characteristics were examined and optimized. The optimum parameters of beam transport system were experimentally determined, and under the proper condition the accelerated proton beam current of 350nA was obtained at the target chamber. Without the high voltage stabilization the observed magnitude of voltage fluctuation was $\Delta$V/ V=5.2$\times$10$^{-3}$ without ion beam and 7.2$\times$10$^{-3}$ with ion beam, respectively, and its apparent ripple frequency for voltage fluctuations was about 3Hz or less. Through the optimized operation of the high voltage stabilization system, the terminal voltage fluctuation was reduced to $\Delta$V/V=2.45$\times$10$^{-4}$ and the energy stability with $\Delta$E/E=2.44$\times$10$^{-4}$ was steadily maintained at the 247.3kV terminal voltage, and the stabilization factor was deduced to be 29.4.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.2
• /
• pp.165-171
• /
• 2022

The SiO₂/TiO₂ multilayer thin films used for narrow band pass filter were fabricated using E-beam evaporation method. The narrow band pass filter was used to enhance the resolution of spectroscopy and sensor applications with near infrared (NIR) light source. The narrow band pass filter with multilayer thin films were designed with Essential Macleod program. The multilayers of SiO₂/TiO₂ with 32 layers were deposited on the silicon encapsulation of IR with peak wavelength (λ_p) of 660 nm and NIR LEDs with λ_p of 830 nm, 880 nm, and 955 nm. After NIR light passed through the narrow band pass filter, the full width of half maximum of 33.4~48.6 nm became narrow to 20~24 nm owing to the absorption of photons with short or long wavelength of designed band of 20 nm. The SiO₂/TiO₂ band pass filter fabricated in this study can be used for sensor, optoelectronics, and NIR spectroscopy applications.