• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.328.1-328
• /
• 2002

MR(Magneto-rheological) fluid is smart fluid that can change its characteristics when magnetic fields are applied. Recently, many researches are going on this MR fluid for the application in a variety of areas including automobile shock absorbers. This paper describes the design procedure of a MR damper and the analysis results of its dynamic characteristics. MR fluid in the magnetic field shows initial yield shear stress and increasing resistive viscousity with final saturation thereafter. (omitted)

• Korea-Australia Rheology Journal
• /
• 제20권4호
• /
• pp.213-220
• /
• 2008

The effects of temperature on the rheological properties of the solutions of poly(vinylidene fluoride-co-hexafluopropylene) (PVDF-HFP) in dimethyl acetamide (DMAc) were investigated in terms of frequency and concentration. The effects of temperature on the intrinsic viscosity of the solutions were discussed. In dynamic rheological measurement, the concentrated solutions showed a little unexpected rheological response; as temperature was increased dynamic viscosity was increased and the solutions exhibited more noticeable Bingham body character over the temperature range, 30 to $70^{\circ}C$. In addition, the solution gave longer relaxation time, lower value of loss tangent and higher value of yield stress at higher temperature and at higher concentration. On the other hand, the dilute solutions revealed that intrinsic viscosity was decreased and its Huggins constant was increased with increasing temperature. These physical parameters suggested that the increase of viscosity with increasing temperature resulted from the localized gelation of PVDF-HFP due to reduced solubility to the solvent.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1995년도 추계학술발표회논문집(2)
• /
• pp.771-776
• /
• 1995

Tensile and J-R tests were carried out to estimate the effects of dynamic strain aging(DSA) on SA106Gr.C piping steel. Tensile tests were performed under temperature range RT to $400^{\circ}C$ md strain rates from $1.39{\times}10^{-4}\;to\;6.95{\times}10^{-2}/s$. Fracture toughness was tested in the temperature range RT to $350^{\circ}C$ and load-line displacement rates 0.4 and 4mm/min. The effects of DSA on the tensile properties were clearly observed for phenomena such serrated flow, variation of ultimate and yield stress, and negative stram rate sensitivity. However, the magnitude of serration and strength increase by DSA was relatively small. this may be due to high ratio of Mn to C. In addition, crack initiation resistance, Ji and crack growth resistance, dJ/da were reduced in the range of $200-300^{\circ}C$, where DSA appeared as serrated flow and UTS hardening. The temperature corresponding to minimum fracture resistance was shifted to higher temperature with increasing loading rate.

• Structural Engineering and Mechanics
• /
• 제74권2호
• /
• pp.255-266
• /
• 2020

The main requirements of modern welded metal structures are the load-carrying capacity (safety), fitness for production, and economy. The primary objective of attaching longitudinal stiffeners is to improve the buckling strength of relatively thin compression panels. This paper gives several comparisons for stiffened plates with different loadings (static, dynamic), different shape of stiffeners (flat, L-shape, trapezoidal), different steel grades, and different welding technologies (SMAW, GMAW, SAW), different costs to show the necessity of a combination of design, fabrication and economic aspects. Safety and fitness for production are guaranteed by fulfilling the design and fabrication constraints. The economy is achieved by minimizing the cost function. It is shown that the optimum sizes depend on the welding technology, the material yield stress, the profile of the stiffeners, the load cycles and the place of the production.

• 유변학
• /
• 제11권2호
• /
• pp.143-152
• /
• 1999

본 연구에서는 Rheometrics Fluids Spectrometer(RFS II)를 사용하여 세 종류의 상용 반고형 식품(마요네즈, 토마토 케찹, 와사비)의 정상유동특성 및 소진폭 전단변형하에서의 동적 점탄성을 광범위한 전단속도와 각주파수 영역에서 측정하였다. 이들 측정결과로부터 정상유동특성의 전단속도 의존성 및 동적 점탄성의 각주파수 의존성을 보고하였다. 그리고 항복응력의 항을 갖는 몇 가지 점소성 유동모델을 사용하여 정상유동특성을 정량적으로 평가하고 이들 모델의 적용성을 비교.검증하였다. 나아가서 수정된 형태의 지수법칙 관계식을 도입하여 정상유동특성(비선형 거동)과 동적 점탄성(선형 거동)간의 상관관계에 대해 검토하였다. 이상의 연구를 통해 얻어진 결과를 요약하면 다음과 같다. (1) 반고형 식품류는 상당한 크기의 항복응력을 갖는 점소성 물질로서 전단속도가 증가할수록 정상류점도가 급격히 감소하는 shear-thinning 거동을 나타낸다. (2) Herschel-Bulkley 모델, Mizrahi-Berk 모델 및 Heinz-Casson 모델은 반고형 식품류의 정상유동거동을 잘 기술할 수 있다. 이들 중에서도 Heinz-Casson 모델이 가장 우수한 적용성을 갖는다 (3) 반고형 식품류는 임계 전단속도를 경계로 shear-thinning 특성이 변화한다. 즉 낮은 전단속도에 비해 높은 전단속도 영역에서 분산입자 응집체의 구조파괴가 더욱 활발하게 진행되어 보다 현저한 shear-thinning 특성을 나타낸다. (4) 저장 탄성률 및 손실탄성률은 양자 모두 각주파수가 증가할수록 점차로 증가하나 각주파수 의존성은 그다지 크지 않다. 또한 광범위한 각주파수 영역에서 탄성적 성질이 점성적 성질에 비해 보다 우세하게 나타난다. (5) 정상류점도, 동적점도 및 복소점도는 모두 power-law 모델의 거동을 잘 만족한다. 또한 정상유동특성과 동적 점탄성간의 상관관계는 수정된 형태의 지수법칙 관계식에 의해 잘 기술될 수 있다.

• Journal of Pharmaceutical Investigation
• /
• 제39권3호
• /
• pp.185-199
• /
• 2009

Using a strain-controlled rheometer [Advanced Rheometric Expansion System (ARES)], the steady shear flow properties and the dynamic viscoelastic properties of $Antiphlamine-S^{(R)}$ lotion have been measured at $20^{\circ}C$ (storage temperature) and $37^{\circ}C$ (body temperature). In this article, the temperature dependence of the linear viscoelastic behavior was firstly reported from the experimental data obtained from a temperature-sweep test. The steady shear flow behavior was secondly reported and then the effect of shear rate on this behavior was discussed in detail. In addition, several inelastic-viscoplastic flow models including a yield stress parameter were employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models was examined by calculating the various material parameters. The angular frequency dependence of the linear viscoelastic behavior was nextly explained and quantitatively predicted using a fractional derivative model. Finally, the strain amplitude dependence of the dynamic viscoelastic behavior was discussed in full to elucidate a nonlinear rheological behavior in large amplitude oscillatory shear flow fields. Main findings obtained from this study can be summarized as follows : (1) The linear viscoelastic behavior is almostly independent of temperature over a temperature range of $15{\sim}40^{circ}C$. (2) The steady shear viscosity is sharply decreased as an increase in shear rate, demonstrating a pronounced Non-Newtonian shear-thinning flow behavior. (3) The shear stress tends to approach a limiting constant value as a decrease in shear rate, exhibiting an existence of a yield stress. (4) The Herschel-Bulkley, Mizrahi-Berk and Heinz-Casson models are all applicable and have an equivalent validity to quantitatively describe the steady shear flow behavior of $Antiphlamine-S^{(R)}$ lotion whereas both the Bingham and Casson models do not give a good applicability. (5) In small amplitude oscillatory shear flow fields, the storage modulus is always greater than the loss modulus over an entire range of angular frequencies tested and both moduli show a slight dependence on angular frequency. This means that the linear viscoelastic behavior of $Antiphlamine-S^{(R)}$ lotion is dominated by an elastic nature rather than a viscous feature and that a gel-like structure is present in this system. (6) In large amplitude oscillatory shear flow fields, the storage modulus shows a nonlinear strain-thinning behavior at strain amplitude range larger than 10 % while the loss modulus exhibits a weak strain-overshoot behavior up to a strain amplitude of 50 % beyond which followed by a decrease in loss modulus with an increase in strain amplitude. (7) At sufficiently large strain amplitude range (${\gamma}_0$>100 %), the loss modulus is found to be greater than the storage modulus, indicating that a viscous property becomes superior to an elastic character in large shear deformations.

• 대한조선학회논문집
• /
• 제60권4호
• /
• pp.213-221
• /
• 2023

The demand for Liquefied Natural Gas (LNG) carriers and LNG-fueled ships has significantly increased in recent years due to the sulfur-oxide emission regulations by the International Maritime Organization (IMO). The main goal of this paper is to introduce the process for the Engineering Critical Assessment (ECA) of IMO independent type-B cargo tanks made from 9% nickel alloy. A methodology proposed by the British Standard was used to conduct ECA for any structure with initial flaws. Based on this standard, a Matlab code was developed to perform ECA. Coarse mesh Finite Element Analysis (FEA) was performed on an independent type-B LNG cargo tank with a capacity of 15,000 m³. The location with the highest development of maximum principal stress was identified at the bottom of the cargo tank. Fine mesh FEA was performed to obtain the stress range required for ECA. The dynamic cargo tank loads used for FEA were determined using some ship rules presented by Det Norske Veritas. As a result of performing a 20-year long-term crack propagation analysis with a semi-elliptical surface crack, the fracture-to-yield ratio exceeded the Fracture Assessment Line (FAL) and some structural reinforcement was necessary. Performing a 15-day short-term crack propagation analysis, the fracture-to-yield ratio remained within the FAL, and no significant LNG leaks were expected. This paper is believed to provide a guide for performing ECA of LNG cargo tanks in the future by providing the basic theory and application sample necessary to perform ECA.

• Steel and Composite Structures
• /
• 제18권1호
• /
• pp.165-185
• /
• 2015

The suspended zipper bracing system is suggested to reduce the flaws of ordinary zipper braced and concentric inverted V braced frames. In the design procedure of suspended zipper bracing systems, columns and top story truss elements are strengthened. This bracing system show different performances and characteristics compared with inverted V braced and ordinary zipper frames. As a result, a different response modification factor for suspend zipper frames is needed. In this research paper, the response modification factor of suspended zipper frames was obtained using the incremental dynamic analysis. Suspended zipper braced frames with different stories and bay lengths were selected to be representations of the design space. To analyze the frames, a number of models were constructed and calibrated using experimental data. These archetype models were subjected to 44 earthquake records of the FEMA-P695 project data set. The incremental dynamic analysis and elastic dynamic analysis were carried out to determine the yield base shear value and elastic base shear value of archetype models using the OpenSEES software. The seismic response modification factor for each frame was calculated separately and the values of 9.5 and 13.6 were recommended for ultimate limit state and allowable stress design methods, respectively.

• Preventive Nutrition and Food Science
• /
• 제20권2호
• /
• pp.137-142
• /
• 2015

Rheological properties of thickened fluids used for consumption by people with dysphagia (swallowing difficulty) are very sensitive to several factors, such as thickener type, temperature, pH, sugar, protein, and NaCl. In this study, steady and dynamic rheological properties of thickened water samples mixed with five commercial xanthan gum-based food thickeners (A~E) were studied in the presence of NaCl at different concentrations (0.3%, 0.6%, 0.9%, and 1.2%). The magnitudes of apparent viscosity (${\eta}_{a,50}$), consistency index (K), yield stress (${\sigma}_{oc}$), and dynamic moduli (G' and G") showed significant differences in rheological behaviors between thickened samples with various NaCl concentrations. Dynamic moduli values of all thickened samples, except for samples with thickener C, were much higher than those of the control (0% NaCl). All rheological parameter values (K, G', and G") in a thickener A were much higher than those in other thickeners. These results suggest that rheological properties of thickened samples containing NaCl are strongly affected by xanthan gum-NaCl interaction and depended on the type of thickener.

• 소성∙가공
• /
• 제16권5호통권95호
• /
• pp.354-359
• /
• 2007

Effects of forging and mechanical properties of 6061 aluminum alloy wheel for automobiles were investigated in the present study. Microstructural and tensile characteristics of automobile wheel after hot forging process using dynamic screw press were analyzed to evaluate effect of metal flow on mechanical properties. The results showed advanced mechanical properties of 6061 alloy wheel because of $Mg_2Si$ precipitation by T6, elongated grain by forging, and work hardening by dense metal flow, etc. Hot compression tests were conducted in order to characterize high temperature compression deformation behaviors and microstructural variation in the range of $300{\sim}450^{\circ}C$, in the strain rate range of $10^{-3}{\sim}10^1\;sec^{-1}$. As strain rate increased, maximum compression stress increased but it was shown the reverse linear relation between temperature and maximum stress irrelevant to strain rate variation. On the other hand, temperature and yield stress didn't have any linear relation and its relation showed big deviation by a function of strain rate and test temperature.