• 한국강구조학회 논문집
• /
• 제26권1호
• /
• pp.21-30
• /
• 2014

본 연구에서는 헤어핀 보강 및 스트럽 보강 선설치앵커의 정적 및 동적 전단하중에 대한 저항강도 평가를 위한 실험을 수행하였다. 보강철근은 D6 이형철근을 사용하였으며 연단거리 120mm의 직경 20mm 앵커에 대해 정적 하중과 1Hz의 편진하중으로 각각 3개의 시험체에 대해 실험을 수행하였다. 헤어핀 보강 앵커는 헤어핀의 덮개가 강도에 직접 영향을 미치는 것으로 확인되었으며, 정적 대비 동적하중에서 강도의 저하는 없는 것으로 평가되었다. 스트럽 보강 앵커는 비보강 앵커에 비해 저항강도의 증가는 미소하였으며 동적하중에 의한 강도는 정적하중에 의한 강도와 거의 같은 값을 보였다.

• Journal of Welding and Joining
• /
• 제23권3호
• /
• pp.40-46
• /
• 2005

Air gun has been one of the good tools to press two sheet metals. However, it is not easy to control the acting force precisely. A Servo-gun is a good tool to control the acting force on the workpiece comparing with the air gun. Servo-gun has a higher tensile shear strength and lower indentation depth as well as smaller spatter. Dynamic resistance was obtained according to the acting force and welding current. As the acting force was changed during welding, the welding quality was increased.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2018년도 추계학술대회
• /
• pp.36-38
• /
• 2018

As the battery capacity requirement increases, battery cells are connected in a parallel configuration. However, the sharing current of each battery cell becomes unequal due to the imbalance between cell's impedance which results the mismatched states of charge (SOC). The conventional fixed-resistance balancing methods have a limitation in battery equalization performance and system efficiency. This paper proposes a battery equalization method based on dynamic resistance technique, which can improve equalization performance and reduce the loss dissipation. Based on the SOC rate of parallel connected battery cells, the switches in the equalization circuit are controlled to change the equivalent series impedance of the parallel branch, which regulates the current flow to maximize SOC utilization. To verify the method, operations of 4 parallel-connected 18650 Li-ion battery cells with 3.7V-2.6Ah individually are simulated on Matlab/Simulink. The results show that the SOCs are balanced within 1% difference with less power dissipation over the conventional method.

• Journal of Korea Trade
• /
• 제27권3호
• /
• pp.87-102
• /
• 2023

Purpose - Although the importance and necessity of "sustainable supply chain management (SCM)" is emphasized, it is often not realized due to conflicting results, the long time required, and large-scale changes brought about by sustainability. This study used the innovation resistance model to confirm the influence of sustainable SCM innovation resistance factors and dynamic capabilities on adoption intentions. This approach made it possible to understand the factors that hinder adoption of sustainability practices and to identify the relationships among influencing factors. It should also help to establish effective policies or strategies. Design/methodology - Through a literature review, the characteristics of sustainable SCM were classified into relative advantage, compatibility, perceived risk, and complexity. The effects of these innovation characteristics on innovation resistance in sustainable SCM and the effects of innovation resistance on adoption intentions were confirmed. In addition, the effects of SCM capabilities on innovation resistance and adoption intentions were analyzed, and the mediating effect of innovation resistance was analyzed. Findings - Compatibility, perceived risk, and flexibility had significant effects on innovation resistance. In turn, innovation resistance had a significant effect on adoption intention, and flexibility had a significant effect on intention to adopt. A partial mediating effect of resistance to innovation was confirmed. Originality/value - Although many previous studies have acknowledged trade-offs with sustainability, most sustainable SCM studies dealt with the correlations among positive drivers of adoption, practices, and performance. This study confirmed the process of accepting sustainable SCM innovation in a single model and is expected to serve as a cornerstone for future sustainable SCM adoption studies. In addition, our findings should help establish effective policies or strategies to activate SSCM adoption by identifying the factors that hinder the adoption of sustainable SCM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1225-1227
• /
• 2005

A Bi-2223 tape has beer developed for power applications such as a fault current limiter, a power cable and a superconducting magnetic energy storage system. In such applications, the Bi-2223 tape carries time varying transport current and in addition experiences time varying external magnetic field. It is well known that the external magnetic field not only causes magnetization loss in the Bi-2223 tape, but also drastically increases transport loss due to a so-called "dynamic resistance". We developed an evaluation setup, which can measure transport loss in external at magnetic fields. Using this equipment, we measured the dynamic resistances for various amplitudes and frequencies of an external ac magnetic field perpendicular to the face in the tape. Simultaneously we investigated the effect of an external ac field on transport loss with different experimental conditions. This paper describes test results and discussions on correlation between the dynamic resistance and the transport loss for the Bi-2223 tape.

• 한국정밀공학회지
• /
• 제2권2호
• /
• pp.43-59
• /
• 1985

In relation to the machinability of drilling operation, experiments were made to investigate the effect of cutting condition on static as well as dynamic cutting resistances in cutting plane carbon steel (SM 45 C) with H.S.S. twist drills. The results were as follows. 1) The static cutting resistances on carbon steel can practically be calculated by the following equations which were derived from experimental result. The deviation from the experimental values was less than 8% and 13% for cutting torque and thrust respectively. For cutting torque M: M=0.019 $H_B\;{f^{0.68}d^{1.68}$ For thrust T: T=0.400406 $r^{0.6}d^{0.68}$ + 0.1835 $H_BC^2$(where $H_B$: Brinnel hardness) 2) The static components of cutting resistance are increased exponentially with increasing drill diameter and feed rate. On the effect of drill diameter, the dynamic components of torque are decreased with increasing dirll diameter because of rigidity, the dynamic components of thrust being not effected with the changes. 3) As feed rates increase, the dynamic components of torque rather decrease although its changes on thrust components are unstable. 4) The static components of cutting resistance and dynamic component of torque are slightly decreased in accordance with the increase of spindle speed although its dynamic thrust components are not effected by the spindle speed.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.143-148
• /
• 1998

A dynamic electrical parameter monitoring device was designed to simultaneously record the instantaneous value of voltage, current, power, and resistance during spot welding. The data obtained using this technique have been analyzed in term of the relationships of these parameters to the phenomena occuring during the formation(surface break-down, nugget formation and mechanical collapse) of spot weld. Finally, a database implementation is undertaken to develop techniques for improving weld quality of the resistance spot welder.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.143-145
• /
• 2003

The purpose of research is to measure power and dynamic resistance value through RMS module. Specially designed RMS-DC hardware module was tested. Its output which is obtained every half cycle was compared with that of commercial weld checker. The results show good agreement and the relative error in the measurement was found to be around 5%.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 추계학술발표대회 개요집
• /
• pp.184-186
• /
• 2001

Quality estimation of the weld has been one of the important issues in RSW which is a main process of the sheet metal fabrication in auto-body industry. It was well known that among the various welding process variables, dynamic resistance has a close relation with nugget formation. In this study, a new quality estimation algorithm is developed with the primary dynamic resistance measured at welding machine timer. For this, Back propagation algorithm of neural network is used.

• Computers and Concrete
• /
• 제26권3호
• /
• pp.275-283
• /
• 2020

Reinforced concrete (RC) does not provide sufficient resistance against impacts and blast loads, and the brittle structure of RC fails to protect against fractures due to the lack of shock absorption. Investigations on improving its resistance against explosion and impact have been actively conducted on high-performance fiber-reinforced cementitious composites (HPFRCCs), such as fiber-reinforced concrete and ultra-high-performance concrete. For these HPFRCCs, however, tensile strength and toughness are still significantly lower compared to compressive strength due to their limited fiber volume fraction. Therefore, in this study, the tensile behavior of slurry-infiltrated fiber-reinforced cementitious composites (SIFRCCs), which can accommodate a large number of steel fibers, was analyzed under static and dynamic loading to improve the shortcomings of RC and to enhance its explosion and impact resistance. The fiber volume fractions of SIFRCCs were set to 4%, 5%, and 6%, and three strain rate levels (maximum strain rate: 250 s^-1) were applied. As a result, the tensile strength exceeded 15 MPa under static load, and the dynamic tensile strength reached a maximum of 40 MPa. In addition, tensile characteristics, such as tensile strength, deformation capacity, and energy absorption capacity, were improved as the fiber volume fraction and strain rate increased.