• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3B
• /
• pp.183-190
• /
• 2003

The explosion of the Internet has brought an acute need for efficient operation, which becomes to develop several technologies based on optical networks. By matching merging technology using wavelength multiplexing, an efficient administration with limited wavelength can provide scalability of network. The merging in optical layer has limitation of devices since the merging can not be performed in this layer. Hence the merging must be implemented in electronic layer. When the merging is implemented, the delay time would be increased in OXC (Optical Cross Connection), but the improvement of throughput rate will be expected in the process of explosive traffic due to reduction of optical channel supporting large bandwidth. In this thesis, we proposed an OXC of dual module having a merging function. We considered the optimum merging point with the largest in system performance and confirmed results using the simulation.

• Proceedings of the KOSOMBE Conference
• /
• v.1996 no.11
• /
• pp.192-196
• /
• 1996

[ $1.06/1.32{\mu}m$ ] dual-wavelength medical laser was developed and preliminary clinical comparisons at these two wavelengths were performed for dental application. We could develop a compact laser system 1) by lasing two wavelengths from the same Nd:YAG rod, and 2) by introducing high-voltage switching power supply modules. Experiment on gingiva of pig jaw showed higher thermal damage at $1.32{\mu}m$. Depending on particular procedures, each wavelength has its own advantages and disadvantages. For cutting, however, using conical tips rather than bare fibers provided better results with low threshold of cutting energy and less surrounding thermal damage. Appling light-absorbing dye on target area appeared to induce more damage during laser irradiation. However, histological studies showed no significant difference whether dye was applied or not.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.12
• /
• pp.1274-1280
• /
• 1997

The photodissociation dynamics of CH2I2 has been studied at 304 nm by state-selective photofragment translational spectroscopy. Velocity distributions, anisotropy parameters, and relative quantum yields are obtained for the ground I(2P3/2) and spin-orbit excited state I*(2P1/2) iodine atoms, which are produced from photodissociation of CH2I2 at this wavelength. These processes are found to occur via B1 ← A1 type electronic transitions. The quantum yield of I*(2P1/2) is determined to be 0.25, indicating that the formation of ground state iodine is clearly the favored dissociation channel in the 304 nm wavelength region. From the angular distribution of dissociation products, the anisotropy parameters are determined to be β(I)=0.4 for the I(2P3/2) and β(I*)=0.55 for the I*(2P1/2) which substantially differ from the limiting value of 1.13. The positive values of anisotropy parameter, however, show that the primary processes for I and I* formation channels proceed dominantly via a transition which is parallel to I-I axis. The above results are interpreted in terms of dual path formation of iodine atoms from two different excited states, i.e., a direct and an indirect dissociation via curve crossing between these states. The translational energy distributions of recoil fragments reveal that a large fraction of the available energy goes into the internal excitation of the CH2I photofragment; < Eint > /Eavl=0.80 and 0.82 for the I and I* formation channels, respectively. The quantitative analysis for the energy partitioning of available energy into the photofragments is used to compare the experimental results with the prediction of direct impulsive model for photodissociation dynamics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.235.1-235.1
• /
• 2015

Artificially-engineered materials, whose electromagnetic properties are not available in nature, such as negative reflective index, are called metamaterials (MMs). Although many scientists have investigated MMs for negative-reflective-index properties at the beginning, their interests have been extended to many other fields comprising perfect lenses. Among various kinds of MMs, metamaterial absorbers (MM-As) mimic the blackbody through minimizing transmission and reflection. In order to maximize absorption, the real and the imaginary parts of the permittivity and permeability of MM-As should be adjusted to possess the same impedance as that of free space. We propose a dual-wide-band and polarization-independent MM-A. It is basically a triple-layer structure made of metal/dielectric multilayered truncated cones. The multilayered truncated cones are periodically arranged and play a role of meta-atoms. We realize not only a wide-band absorption, which utilizes the fundamental magnetic resonances, but also another wide-band absorption in the high-frequency range based on the third-harmonic resonances, in both simulation and experiment. In simulation, the absorption bands with absorption higher than 90% are 3.93 - 6.05 GHz and 11.64 - 14.55 GHz, while the experimental absorption bands are in 3.88 - 6.08 GHz and 9.95 - 13.84 GHz. The physical origins of these absorption bands are elucidated. Additionally, it is also polarization-independent because of its circularly symmetric structures. Our design is scalable to smaller size for the infrared and the visible ranges.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.1
• /
• pp.85-90
• /
• 2008

In this paper, we studied on dual reflector adjusted to monopulse antenna system. As a result, when the efficiency of main reflector is more than 70%, The size of reflector is 30 wavelength of maximum frequency and minimum frequency gain is 37.9dBi, and Maximum frequency gain is 38.6dBi. Also, when a radius is D and Focus-distance is $F_e$, a scheme for efficiency improvement of Sub Reflector is to increase the Focus-distance to Diameter Ratio. In this case, Cross polarization in Far field improved and spherical spreading loss in circumference of reflector reduced. The influence of Radiation pattern followed by the side displacement of feed antenna(at $x_sy_s$) is decreased, it is confirmed that performance of scanning is improved.

• Korean Journal of Plant Resources
• /
• v.10 no.2
• /
• pp.183-187
• /
• 1997

This study was carried out to find the growth characteristics and content of sarsasapogenin in different plant parts of Anemarrhena asphodeloides Bunge. Five native-cultivars were collected and evaluated for several agronomic traits. The collected native-cultivars were classified into two seed-attached peduncle and vegetative propagation types. Seed-attached peduncle lines were predominance of growth traits than vegetative propagation. For the content of sarsasapogenin in each part was investigated, BuOH extarct of 'timo' was developed on silica gel 60G plate using elution solvent($CHC1_2$: Methyl ethyl Ketone : EtOH = 11 : 2 : 0.5). The developed plate were examined using Dual Wavelength Zig - Zag using. Content of sarsasapogenin in main root and lateral root were respectively 1.67mg/g and 1.31mg/g.

• Journal of Sensor Science and Technology
• /
• v.25 no.2
• /
• pp.124-130
• /
• 2016

NDIR $CO_2$ gas sensor was built with ASIC implemented thermopile sensor which included temperature sensor and unique elliptical waveguide structures in this paper. The temperature dependency of dual infrared sensor module ($CO_2$ and reference IR sensors) has been characterized and its output voltage characteristics according to the temperature and gas concentration were proposed for the first time. NDIR $CO_2$ gas and reference IR sensors showed linear output voltages according to the variation of ambient temperatures from 243 K to 333 K and their slopes were 14.2 mV/K and 8.8 mV/K, respectively. The output voltages of temperature sensor also presented a linear dependency according to the ambient temperature and could be described with V(T)=-3.191+0.0148T(V). The output voltage ratio between $CO_2$ and reference IR sensors revealed irrelevant to the changes of ambient temperatures and gave a constant value around 1.6255 with standard deviation 0.008 at 0 ppm. The output voltage of $CO_2$ gas sensor at zero ppm $CO_2$ gas consisted of two components; one is caused by the HPB (half pass-band) of IR filter and the other is attributed to the part of $CO_2$ absorption wavelength. The characteristics of output voltages of $CO_2$ gas sensor could be accurately modeled with three parameters which are dependent upon the ambient temperatures and represented small average error less than 1.5% with 5% standard deviation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.309-310
• /
• 2005

In the fabrication of high performance red organic light emitting diode, 2-TNA TA [4,4',4" -tris (2-naphthylphenyl- phenylamino)-triphenylamine] as hole injection material and N PH [N,N'-bis (1-naphthyl) -N,N' -diphenyl-1, 1'-biphenyl-4,4'- diamine] as hole transport material were deposited on the ITO (indium tin oxide)/glass substrate by vacuum evaporation, And then, red color emission layer was deposited using Alq3 as a host material and Rubrene (5,6,11,12- tetraphenylnaphthacene) and GDI 4234 as dopants. Finally, small molecular weight OLED with the structure of ITO/2-TNATA/ NPB/Alq3+Rubrene+GDI4234/Alq3/LiF/Al was obtained by in-situ deposition of Alq3, LiF and Al as electron transport material, electron injection material and cathode. respectively. Green OLED fabricated in our experiments showed the color coordinate of CIE(0.65,0.35) and the maximum luminescence efficiency of 2.1 lm/W at 7 V with the peak emission wavelength of 632 nm.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.24 no.3
• /
• pp.453-460
• /
• 2014

Fault injection attack is the process of attempting to acquire the information on-chip through inject artificially generated error code into the cryptographic algorithms operation (or perform) which is implemented in hardware or software. From the details above, the laser-assisted failure injection attacks have been proven particularly successful. In this paper, we propose an improved laser probing system for fault injection attack which is called the Dual-Laser FA tool set, a hybrid approach of the Flash-pumping laser and fiber laser. The main concept of the idea is to improve the laser probe through utilizing existing equipment. The proposed laser probe can be divided into two parts, which are Laser-I for laser cutting, and Laser-II for fault injection. We study the advantages of existing equipment, and consider the significant parameters such as energy, repetition rate, wavelength, etc. In this approach, it solves the high energy problem caused by flash-pumping laser in higher repetition frequency from the fiber laser.

• Journal of Advanced Navigation Technology
• /
• v.27 no.4
• /
• pp.463-468
• /
• 2023

In this paper, we proposed reconfigurable dual polarization patch array antenna that can select two polarizations(Vertical, RHCP) using defected ground structure and Pin diode. The proposed antenna was designed arranging a circular polarization patch antenna implemented with a square microstrip patch and two slots 3x3 at 25.8mm placed, a half-wavelength of 5.8 GHz. Conect the pin diode and the capacitor to the slot diagonally placed on the ground of each antennas, and select polarization using the open/short operating according to the application of DC voltage to the pin diode. As a result of the design, the gain of the antenna is 11.7 dBi at vertical polarization and 11.6 dBic at RHCP. The axial ratio is 20.3 dB at 1.8 dB vertical polarization at RHCP. Mutual Coupling is Maximum to -20.8 dB for vertical polarization and Maximum to -30.1 dB for RHCP.