• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.1947-1953
• /
• 2009

Metal halide (MH) lamps have been largely used due to high luminous efficiency, good color rendering, and long life. Since the metal halide lamps have problems of high ignition voltage and acoustic resonance. Thus, the design of ballast is very difficult for engineers. This paper proposes prototype of electric ballast in order to solve above two problems. The proposed electric ballast is consisted of EMI filter, full wave rectifier circuit, active PFC, DBI(Dual Buck Inverter), dimming circuit and ignitor circuit. The DBI supplies both rectangular voltage and current to the lamp. As the result of the experiment, the acoustic resonance was eliminated and the ignitor circuit was designed to generate high ignition voltage than 5kV. It makes the dimming circuit possible to control the lamp power in range between 230W and 350W.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.40-47
• /
• 2016

In this paper, a dual mode buck converter with an ability to change mode is proposed, which is suitable particularly for portable device. The problem of conventional mode control circuit is affected by load variation condition such as suddenly or slowly. To resolve this problem, the mode control was designed with slow clock method. Also, when change from the PFM(Pulse Frequency Modulation) mode to the PWM(Pulse Width Modulation) mode, to use the counter to detect a high load. And the user can select mode transition point in load range from 20mA to 90mA by 3 bit digital signal. The circuits are implemented by using BCDMOS 0.18um 2-polt 3-metal process. Measurement environment are input voltage 3.7V, output voltage 1.2V and load current range from 10uA to 500mA. And measurement result show that the peak efficiency is 86% and ripple voltage is less 32mV.

• Journal of Power Electronics
• /
• v.12 no.4
• /
• pp.519-527
• /
• 2012

A high step-down multiple-output LED driver is proposed in this paper. Firstly, the derivation of the driver with dual-output is presented and its operation principle and steady state performance are analyzed in detail. Secondly, a high step-down N-channel LED driver is proposed and its current auto-balance characteristic and step-down ratio are analyzed. Finally, an experimental prototype is built and the experimental results are given. The theoretical analysis and experimental results show that the proposed driver has the following virtues: First, if load balancing is achieved, the voltage gain is 1/N that of a Buck driver, where N is the number of channels. Second, each output automatically has an equal output current, without requiring more current close-loop control circuits than a Buck driver. Last, the voltage stresses of the switches and diodes are lower than those of a Buck driver, meaning that lower voltage switches and diodes can be used, and a higher efficiency can be expected.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.802-809
• /
• 2014

This paper presents a dual-mode bias modulator (BM) for complementary metal oxide semiconductor (CMOS) power amplifiers (PAs). The BM includes a hybrid buck converter and a normal buck converter for an envelope tracking (ET) mode for high output power and for an average power tracking (APT) mode for low output power, respectively. The dual-mode BM and CMOS PA are designed using a $0.18-{\mu}m$ CMOS process for the 1.75 GHz band. For the 16-QAM LTE signal with a peak-to-average power ratio of 7.3 dB and a bandwidth of 5 MHz, the PA with the ET mode exhibited a poweradded efficiency (PAE) of 39.2%, an EVM of 4.8%, a gain of 19.0 dB, and an adjacent channel leakage power ratio of -30 dBc at an average output power of 22 dBm, while the stand-alone PA has a PAE of 8% lower at the same condition. The PA with APT mode has a PAE of 21.3%, which is an improvement of 13.4% from that of the stand-alone PA at an output power of 13 dBm.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.4
• /
• pp.224-230
• /
• 2006

The conventional way to implement a bidirectional converter with boost/buck has been to use two general purpose PWM ICs with a single supply voltage. In this case, when one direction mode is in operation, the other is disabled and the output of the error amplifier of the disabled IC may be saturated to a maximum value or zero. Therefore, during mode transition, a circuit which can disable the switching operation for a certain time interval is required making it impossible to get a seamless transition. In this paper, the limitations of the conventional 42V/14V bi-directional DC/DC converter implemented with general current mode PWM ICs with a single supply voltage are reviewed and a new current mode PWM controller circuit with a dual voltage system is proposed. The validity of the proposed circuit is investigated through simulation. and experiments.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.8
• /
• pp.35-40
• /
• 2012

In DC-DC converters, a PWM/PFM dual mode control method is commonly used to maintain a high efficiency over a wide range of load variation. Since the control mode is selected according to the load condition, the chip area is increased due to additional circuit for mode control and the optimum efficiency cannot be achieved around the mode transition point. To solve such problems, a new integrated control method is proposed in this paper, in which a PLL is used in the current mode PWM control circuit instead of an oscillator. The proposed integrated control method is verified through a design of a buck converter using PSIM simulation. Simulation of the complete buck converter circuit by Cadence Spectre showed a maximum efficiency of 94.7% at a load current of 250mA and an efficiency of 85.4% at a load current of 10mA under the light load condition.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.342-343
• /
• 2018

듀얼벅 인버터는 효율이 높고 누설전류가 작다는 장점을 가지지만, 단방향 전력 전달 특성으로 인해 적용범위에 한계가 존재한다. 이에 본 논문에서는 듀얼벅 인버터의 무효전력 보상을 위한 새로운 모듈레이션 기법을 제안한다. 제안하는 모듈레이션 기법을 적용할 경우 회로를 수정하지 않고 듀얼벅 인버터의 장점을 유지한 채 무효전력 출력이 가능하다. 이를 시뮬레이션 및 실험을 통해 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.37-39
• /
• 2019

본 논문에서는 듀얼 벅 멀티레벨 컨버터의 일반화된 회로구성을 제안한다. 기존의 멀티레벨 컨버터는 스위칭 상태 전환시암(arm)의 단락을 의미하는 슛-스루(shoot-through) 문제가 존재하므로 데드 타임이 필수적으로 요구되지만 제안되는 듀얼 벅 멀티레벨 컨버터에서는 이러한 문제점이 해결된다. 본 논문에서는 시뮬레이션과 실험을 통하여 제안되는 듀얼 벅 멀티레벨 컨버터의 효과와 유효성을 검증한다.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.143-149
• /
• 2016

The two-stage converter is widely used in traditional DC/AC inverter. It has several disadvantages such as complex topology, large volume and high loss. In order to overcome these shortcomings, a novel half load-cycle worked dual SEPIC single-stage inverter, which is based on the analysis of the relationship between input and output voltages of SEPIC converters operating in the discontinuous conduction mode (DCM), is presented in this paper. The traditional single-stage inverter has remarkable advantages in small and medium power applications, but it can’t realize boost DC/AC output directly. Besides one pre-boost DC/DC converter is needed between the DC source and the traditional single-stage inverter. A novel DC/AC inverter without pre-boost DC/DC converter, which is comprised of two SEPIC converters, is studied. The output of dual SEPIC converters is connected with anti-parallel and half load-cycle control is used to realize boost and buck DC/AC output directly and work properly, whatever the DC input voltage is higher or lower than the AC output voltage. The working principle, parameter selection and the control strategy of the inverters are analyzed in this paper. Simulation and experiment results verify the feasibility of the new inverter.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.226-239
• /
• 2018

In this paper, design and control method ZVT Interleaved Bidirectional LDC(IB-LDC) for mild-hybrid electric vehicle is proposed. The IB-LDC is composed of interleaved buck and boost converters employing an auxiliary inductor and auxiliary capacitors to achieve zero-voltage-transition. Operating principle of IB-LDC according to operation mode is introduced and mathematically analyzed in buck and boost mode. Moreover, PFM and phase control are proposed to reduce circulating current for low power range. Passive components design such as main inductor, auxiliary inductor and capacitors is suggested, considering ZVT condition and maximizing efficiency. Furthermore, a 600W prototype of ZVT IB-LDC for MHEVs is built and tested to verify validity.