• ETRI Journal
• /
• v.41 no.2
• /
• pp.167-175
• /
• 2019

A wideband dual-polarized antenna coupling cross resonator is proposed for LTE700/GSM850/GSM900 base stations. An additional resonance is introduced to obtain strong coupling between the dipole and resonator. Moreover, the input impedance of the proposed antenna is steadily close to $50{\Omega}$, which results in better impedance matching. Therefore, a wide bandwidth can be achieved with multiresonance. A prototype is fabricated to verify the proposed design. The measured results show that the antenna has a fractional bandwidth of 35.7% from 690 MHz to 990 MHz for ${\mid}S_{11}{\mid}$ < -15 dB. Stable radiation patterns as well as gain are also obtained over the entire operating band. Moreover, a five-element antenna array with an electrical downtilt of $0^{\circ}$to $14^{\circ}$ is developed for modern base station applications. Measurement shows that a wide impedance bandwidth of 34.7% (690 MHz to 980 MHz), stable HPBW (3-dB beamwidth) of $65{\pm}5^{\circ}$, and high gain of $13.8{\pm}0.6dBi$ are achieved with electrical downtilts of $0^{\circ}$, $7^{\circ}$, and $14^{\circ}$.

• Journal of electromagnetic engineering and science
• /
• v.18 no.3
• /
• pp.182-187
• /
• 2018

A low profile asymmetrical fractal boundary patch antenna based on reactive impedance surface (RIS) and a mushroom unit cell (MUC) is proposed and studied for dual band operation. The sides of the square patch antenna are replaced with asymmetrical half circled fractal curves for circular polarization operation at patch mode band. The fractal patch antenna is loaded with MUC for dual band operation. The antenna radiation characteristics are investigated and illustrated with both simulated and experimental results in detail. The 10-dB return loss bandwidth are 8.48% (3.21-3.49 GHz) and 2.59% (2.30-2.36 GHz) at upper and lower resonance frequencies, respectively. The 3-dB axial ratio bandwidth is 4.26% (3.21-3.35 GHz). A close agreement between simulation data with experimental results is observed.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.241-245
• /
• 2002

Dual-band microstrip antenna is designed for industrial-scientific-medical(ISM) band of 2.4㎓ and 5.8㎓ using finite-difference time-domain method(FDTD). Cross Patch fed by aperture in the ground plane of microstrip line is proposed as radiation element of antenna, which is 2 rectangular Patch is overlapped. To design antenna, change of input impedance by aperture and stub length change is examined. And it is investigated that center frequency and -10 ㏈ bandwidth by Length of radiation element and width change. Experimental result about reflection Loss confirmed that agree well with analysis results of FDTD and IE3D, And -3 ㏈ beam width, front to back ratio and gain in frequency 2.43㎓ and 5.79㎓ is presented by measuring radiation Pattern of antenna.

• International Journal of Internet, Broadcasting and Communication
• /
• v.9 no.1
• /
• pp.29-34
• /
• 2017

Over the past several decades, embedded system and flight control computer technologies have been evolved to meet the diverse needs of the mobile device market. Current embedded systems are at the heart of technologies that can take advantage of small-sized specialized hardware while still providing high-efficiency performance at low cost. One of these key technologies is multiple memory banks. For example, a dual memory bank can provide two times more memory bandwidth in the same memory space. This benefit take lower cost to provide the same bandwidth. However, there is still few software technologies to support the efficient use of multiple memory banks. In this study, we present a technique to efficiently exploit multiple memory banks by software support. Specifically, our technique use an interference graph to optimally allocate data to different memory banks by an optimizing compiler. As a result, the execution time can be improved upto 7% with the proposed technique.

• ETRI Journal
• /
• v.33 no.6
• /
• pp.985-988
• /
• 2011

A novel application of a dual-transmission line is proposed to design a lowpass filter (LPF). The proposed structure uses only transmission line elements to produce an equiripple LPF response with sharp roll-off. Design equations are derived using a lossless transmission line model. Controlling the electrical lengths, three transmission-zeros are realized in the stopband to obtain a sharp roll-off rate and wide stopband bandwidth. A single unit microstrip LPF with a 3-dB cut-off frequency at 1.0 GHz having a roll-off of 135 dB/GHz along with a stopband bandwidth of 69.5% is designed for validation.

• Current Optics and Photonics
• /
• v.5 no.3
• /
• pp.289-297
• /
• 2021

We describe a comb-mode resolving spectroscopic technique by direct time-domain phase correction of unstable interferograms obtained from loosely locked two femtosecond lasers. A low-cost continuous wave laser and conventional repetition rate stabilization method were exploited for locking carrier and envelope phase of interferograms, respectively. We intentionally set the servo control at low bandwidth, resulting in severe interferograms' fluctuation to demonstrate the capability of the proposed correction method. The envelope phase of each interferogram was estimated by a quadratic fit of carrier peaks to correct timing fluctuation of interferograms in the time domain. After envelope phase correction on individual interferograms, we successfully demonstrated 1 Hz linewidth of RF comb-mode over 200 GHz optical spectral-bandwidth with 10-times signal-to-noise ratio (SNR) enhancement compared to the spectrum without correction. Besides, the group delay difference between two femtosecond pulses is successfully estimated through a linear slope of phase information.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1309-1314
• /
• 2003

The high precision positioning mechanism is used in various industrial fields. It is used in semiconductor manufacturing line, test instrument, Bioengineering, and MEMS and so on. This paper presents a positioning mechanism with dual servo system. Dual servo system consists of a coarse stage and a fine motion stage. The course stage is driven by VCM and the actuator of fine stage is the PZT. The purposes of dual servo system are stability, higher bandwidth, and robustness. Lead compensator is applied to this control system, and is designed by PQ method. Designed compensator can improve property of positioning mechanism.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.237-242
• /
• 2000

The areal recording density of HDD(Hard Disk Drive) has been increasing by about 60% a year. In order to achieve high areal density, less track pitch is expected and more servo bandwidth is required. Dual stage actuator and servo controller for HDD have been suggested for achieving high track density as a possible solution. Dual-loop servo system is generally classified into a two-input-two-output system, but if we use an estimator for a two-input-two-output system, it can be converted into two input one output system. Since we can't control the dual stage servo system by the classical method, it requires a special technique; for example, Parallel Loop System, Master-Slave Loop System, Decoupled Master-Slave Loop System, and Dual Feedback Loop System. In this paper, we performed experimental evaluations of several types of control algorithm. Further experiments will be made in the future.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.3
• /
• pp.163-169
• /
• 2017

This paper proposed a method of broadband method of dual polarized dipole antenna for 700 MHz band base station. The proposed antenna has a structure that PCB feeder is mounted on the metallic radiator. The design of radiator and feeder is optimized by using 3D EM simulation. The proposed antenna(bandwidth 31.6 %) is broadened over 12.2 % through the lower frequency band than reference antenna(bandwidth 19.4 %), however the size is not increased. Measured results of S-parameters, radiation patterns, and gain have a good agreement with simulation ones.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.580-583
• /
• 2007

In this paper, we proposed a slot antenna for dual band ISM that was transformed from a slot antenna structure. Proposed antenna was designed and fabricated that transformed feed line was changed existing slot antenna feed line to appear resonances at dual band. Bandwidth of the designed and fabricated slot antenna for ISM dual band is 8.23%, 4.8% at the resonated frequency at 2.45 GHz, 5 GHz. And we observed the resonant frequency and bandwidth according to change of feed line and slot length. Also, the measured radiation pattern characteristic of fabricated antenna is compared and analyzed E-plane and H-plane at 2.45 GHz, 5GHz.