• 한국전자파학회논문지
• /
• 제25권9호
• /
• pp.903-911
• /
• 2014

본 논문에서는 광대역 수신기에서 고속으로 동작하며, 위상 잡음의 크기와 형태를 개선한 이중 PLL 구조 주파수 합성기를 제안한다. 위상 잡음 및 불요신호의 개선을 위해 두 번째 PLL의 기준 주파수로 사용되는 첫 번째 PLL의 출력주파수를 변경하였다. 6.5~8.5 GHz에서 동작하며, 디지털 NCO(Numerically Controlled Oscillator)와 연계하여 주파수 해상도 1 Hz를 만족하는 주파수 합성기를 설계하였고, 제작된 주파수 합성기는 동조속도 60 us 이내로 동작하며, 출력 전력은 약 -3 dBm 이상, 위상 잡음은 10 kHz offset에서 -95 dBc/Hz 이하를 만족한다.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.401-407
• /
• 2011

In order to enhance torque density of five-phase permanent magnetic synchronous motor with third harmonic injection for electric vehicles (EVs) applications, optimum seeking method for injection ratio of third harmonic was proposed adopting theoretical derivation and finite element analysis method, under the constraint of same amplitude for current and air-gap flux. By five-dimension space vector decomposition, the mathematic model in two orthogonal space plane, $d_1-q_1$ and $d_3-q_3$, was deduced. And the corresponding dual-plane vector control method was accomplished to independently control fundamental and third harmonic currents in each vector plane. A five-phase PMSM prototype with quasi-trapezoidal flux pattern and its fivephase voltage source inverter were designed. Also, the dual-plane vector control was digitized in a single XC3S1200E FPGA. Simulation and experimental results prove that using the proposed optimum seeking method, the torque density of five-phase PMSM is enhanced by 20%, without any increase of power converter capacity, machine size and iron core saturation.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1614-1622
• /
• 2014

A novel equivalent flux sliding-mode observer (SMO) is proposed for dual three-phase interior permanent magnet synchronous motor (DT-IPMSM) drive system in this paper. The DT-IPMSM has two sets of Y-connected stator three-phase windings spatially shifted by 30 electrical degrees. In this method, the sensorless drive system employs a flux SMO with soft phase-locked loop method for rotor speed and position estimation, not only are low-pass filter and phase compensation module eliminated, but also estimation accuracy is improved. Meanwhile, to get the regulator parameters of current control, the inner current loop is realized using a decoupling and diagonal internal model control algorithm. Experiment results of 2MW-level DT-IPMSM drives system show that the proposed method has good dynamic and static performances.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.270-273
• /
• 2000

A new phase shift PWM parallel-input/series-output modularized dual converter is proposed in this paper. This converter is operated with a fixed duty ratio and its output voltage is regulated by phase shift between each module. Since the operating duty ratio of each module is fixed it is sufficient to implement a simple open loop drive circuitry for each module and the cost of total system can be much reduced. The operation of the converter is analyzed in this paper and verified by computer simulation.

• Journal of Communications and Networks
• /
• 제12권3호
• /
• pp.246-252
• /
• 2010

A binary linear integer program is formulated for the problem of expanding the capacity of a fiber optic network and routing the traffic to deliver new interactive multimedia services. A two-phase Lagrangian dual search procedure and a Lagrangian heuristic are developed. Computational results show superior performance of the two-phase subgradient optimization compared with the conventional one-phase approach.

• 한국재료학회지
• /
• 제19권6호
• /
• pp.305-312
• /
• 2009

The effects of Quenching and Partitioning (Q&P) and Annealed Martensite (AM) heat treatment on the microstructure and tensile properties were investigated for 0.24C-0.5Si-1.5Mn-1Al steels. The Q&P steels were annealed at a single phase ($\gamma$) or a dual phase (${\gamma}+{\alpha}$), followed by quenching to a temperature between $M_s$ and $M_f$. Then, enriching carbon was conducted to stabilize the austenite through the partitioning, followed by water quenching. The AM steels were intercritically annealed at a dual phase (${\gamma}+{\alpha}$) temperature and austempered at $M_s$ and $M_s{\pm}50^{\circ}C$, followed by cooling in oil quenching. The dual phase Q&P steels showed lower tensile strength and yieldyield strength than those of the single phase Q&P steels, and tThe elongation for the dual phase Q&P steel was partitioning 100s higher than that of that for the single phase Q&P steels as the partitioning time was less than 100s up to partitioning 100s. For AM steels, the tensile/yield strength decreased and the total elongation increased as the austempering temperature increased. The stability of the retained austenite controlled the elongation for Q&P steels and the volume fraction of the retained austenite controlled the elongation for AM steels.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1836-1840
• /
• 2003

This paper, we propose a new phase-locked loop (PLL) system with the controllable output phase, independent from the output frequency, and lock-up time. This PLL system has a dual control loop is described, the inner loop greatly improved VCO characteristic such as faster speed response as well as higher operation bandwidth, to minimize the effect of the VCO noise and the power supply variation and also get better linearity of VCO output. The main loop is the heart of this PLL which greatly improved the output frequency instability due to the external high frequency noise coupling to the input reference frequency also the main loop can control the output phase, independent from the output frequency, and reduce the lock-up time of the step frequency response. The experimental results confirm the validity of the proposed strategy.

• 천문학회보
• /
• 제36권2호
• /
• pp.128.1-128.1
• /
• 2011

We present the results of the first simultaneous dual-frequency VLBI observation with KVN (Korean VLBI Network). The KVN has a unique multi-frequency receiving system performing simultaneous observations at four frequencies, such as 22, 43, 86, and 129 GHz, in order to calibrate the atmospheric phase fluctuations, which cause a severe degradation of an interferometric coherence in mm-VLBI regime. In order to test the multi-frequency phase referencing capability of KVN, we observe the bright continuum VLBI source, NRAO 150 at two different frequencies of 21.7 (K band) and 43.4 (Q band) GHz simultaneously. The VLBI fringe phases at K and Q bands show a tight correlation of phase behaviors and the results of phase referencing (residual phase, coherence etc) are promising for achieving excellent phase referencing observations with KVN. The KVN will be able to open new perspectives in the multi-frequency study of VLBI.

• Current Optics and Photonics
• /
• 제5권3호
• /
• pp.289-297
• /
• 2021

We describe a comb-mode resolving spectroscopic technique by direct time-domain phase correction of unstable interferograms obtained from loosely locked two femtosecond lasers. A low-cost continuous wave laser and conventional repetition rate stabilization method were exploited for locking carrier and envelope phase of interferograms, respectively. We intentionally set the servo control at low bandwidth, resulting in severe interferograms' fluctuation to demonstrate the capability of the proposed correction method. The envelope phase of each interferogram was estimated by a quadratic fit of carrier peaks to correct timing fluctuation of interferograms in the time domain. After envelope phase correction on individual interferograms, we successfully demonstrated 1 Hz linewidth of RF comb-mode over 200 GHz optical spectral-bandwidth with 10-times signal-to-noise ratio (SNR) enhancement compared to the spectrum without correction. Besides, the group delay difference between two femtosecond pulses is successfully estimated through a linear slope of phase information.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 통신소사이어티 추계학술대회논문집
• /
• pp.64-67
• /
• 2003

This paper presents the design of dual-band VCO using PBG structure for IEEE 802.11A/B. By adding switch circuit to the single-band VCO, we could achieve a dual-band VCO. The center frequencies of dual-band VCO are 5.93GHz(-13dBm) and 2.37GHz (3.50dBm). The phase noise is improved about l0dB by using PBG Structure.