• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.54-64
• /
• 2015

This paper presents a current sensorless maximum power point tracking (MPPT) control method for dual-mode photovoltaic (PV) module-type interleaved flyback inverters (ILFIs). This system, called the MIC (Module Integrated Converter), has been recently studied in small PV power generation systems. Because the MIC is an inverter connected to one or two PV arrays, the power system is not affected by problems with other inverters. However, since the each PV array requires an inverter, there is a disadvantage that the initial installation cost is increased. To overcome this disadvantage, this paper uses a flyback inverter topology. A flyback inverter topology has an advantage in terms of cost because it uses fewer parts than the other transformer inverter topologies. The MPPT control method is essential in PV power generation systems. For the MPPT control method, expensive dc voltage and current sensors are used in the MIC system. In this paper, a MPPT control method without current sensor where the input current is calculated by a simple equation is proposed. This paper also deals with dual-mode control. Simulations and experiments are carried out to verify the performance and effectiveness of the proposed current sensorless MPPT control method on a 110 [W] prototype.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.3
• /
• pp.199-205
• /
• 2017

In a small cell base station used in densely populated areas, a dual polarized multiple antenna(MIMO) is mainly used to increase the cell capacity. This paper demonstrates a dual-polarization antenna with high cross-polarization discrimination(XPD) that can improve the capacity of a small cell using a dual polarization multiple antenna (MIMO). By using the symmetric structure and differential feeding, high XPD in all directions is achieved. In addition, a very similar radiation pattern is observed between each polarization. Because of high XPD and similar radiation pattern in all directions, proposed antenna is well adopted for small-cell multiple-input multiple-output(MIMO) system. Experimental results shows that the proposed antenna has a bandwidth of 180 MHz (2.51~2.7 GHz), a maximum gain of 4.5 dBi (3.5~4.5 dBi), and a half-power beam width of 85 degrees. In addition, average XPD of 26.4 dB in all directions, more than 13.8 dB increase than previous dual-polarization antennas which use single emitter by using different feeding or selectively use polarization through switching.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.112-114
• /
• 2019

본 논문에서는 DC 배전 시스템을 위한 새로운 다중 모드 단일 인덕터 회로를 제안한다. 제안하는 컨버터는 벅 컨버터에 배터리 스위칭 셀이 병합된 구조로서, 단일 인덕터를 사용하여 두 개의 출력 제어가 가능하다. 기존의 회로와 비교해보았을 때, 전체 소자수가 증가하였음에도 불구하고 감소한 인덕터 개수로 인해 전체 시스템의 가격 저감에 효과적이며 높은 전력밀도를 달성할 수 있다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2259-2264
• /
• 2013

In this paper, a selective multiple-input multiple-output(MIMO) transmission scheme is proposed in dual-hop MIMO relaying systems, in which orthogonal space-time block code(OSTBC) transmission and transmit antenna selection(TxAS) transmission are selectively used. Assuming independent Rayleigh fading channels, the outage probability is analyzed for a decode-and-forward(DF) relaying system using the selective MIMO transmission scheme. Also, through numerical investigation, the outage performance for the DF relaying system using the selective MIMO transmission scheme is compared with that for the conventional DF relaying system using OSTBC or TxAS. Moreover, from the performance comparison, it is shown that the proposed scheme can reduce the system overhead without outage performance degradation.

• Journal of Power Electronics
• /
• v.1 no.2
• /
• pp.78-87
• /
• 2001

A new high-power step-up based on the two-module parallel-input (PISO) modular dual inductor-fed push-pull converter is proposed. The proposed converter is operated at a constant duty cycle and employs and auxiliary circuit to control the output voltage with a phase-shift between two modules. It shows a high efficiency due to the greatly reduced switch turn-off stress. It also shows a high and linear voltage conversion ratio, low current stress in the output capacitor, and fast control-to-output dynamics. The operation principles and the mathematical models of the proposed converter are presented. Features of the proposed converter are discussed in comparison with the two-module PISO modular dual inductor-fed push-pull converter. Also, experimental results from a 50kHz, 800W, 350 Vdc prototype with an input voltage range of 20-32 Vdc are provided to confirm the validity of the proposed converter. The new converter compares favorably with the conventional counterpart, and is considered well siuted to high-power step-up applications.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2000.12a
• /
• pp.205-208
• /
• 2000

In this paper, we'll show that an improved PDFF controller is obtained by substituting a feedforward compensator in the existing PDFF system with a dual-input describing function, and the controller has the ability of adjusting the bandwidth of a system as well as the phase margin simultaneously. The effectiveness of the proposed controller is confirmed by applying to the DC-motor position control system. As the results of simulation, we know that it is possible to design a controller by which the bandwidth of the closed system and its phase margin are easily adjusted.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.2
• /
• pp.42.3-42.3
• /
• 2019

We translate Solar Dynamics Observatory/Atmospheric Imaging Assembly (AIA) ultraviolet (UV) multi-channel images into another UV single-channel image using a deep learning algorithm based on conditional generative adversarial networks (cGANs). The base input channel, which has the highest correlation coefficient (CC) between UV channels of AIA, is 193 Å. To complement this channel, we choose two channels, 1600 and 304 Å, which represent upper photosphere and chromosphere, respectively. Input channels for three models are single (193 Å), dual (193+1600 Å), and triple (193+1600+304 Å), respectively. Quantitative comparisons are made for test data sets. Main results from this study are as follows. First, the single model successfully produce other coronal channel images but less successful for chromospheric channel (304 Å) and much less successful for two photospheric channels (1600 and 1700 Å). Second, the dual model shows a noticeable improvement of the CC between the model outputs and Ground truths for 1700 Å. Third, the triple model can generate all other channel images with relatively high CCs larger than 0.89. Our results show a possibility that if three channels from photosphere, chromosphere, and corona are selected, other multi-channel images could be generated by deep learning. We expect that this investigation will be a complementary tool to choose a few UV channels for future solar small and/or deep space missions.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.12
• /
• pp.78-83
• /
• 2010

In this paper, a novel dual-band power amplifier using metamaterials has been realized with one RF GaN HEMT diffusion metal-oxide-semiconductor field effect transistor. The CRLH TL can lead to metamaterial transmission line with the dual-band tuning capability. The dual-band operation of the CRLH TL is achieved by the frequency offset and the nonlinear phase slope of the CRLH TL for the matching network of the power amplifier. We have managed only the second- and third-harmonics to obtain the high efficiency with the CRLH TL in dual-band. Also, the proposed power amplifier has been realized by using the harmonic control circuit for not only the output matching network, but also the input matching network for better efficiency. Two operating frequencies are chosen at 900 MHz and 2140 MHz in this work. The measured results show that the output power of 39.83 dBm and 35.17 dBm was obtained at 900 MHz and 2140 MHz, respectively. At this point, we have obtained the power-added efficiency (PAE) and IMD of 60.2 %, -23.17dBc and 67.3 %, -25.67dBc at two operation frequencies, respectively.

• Journal of IKEEE
• /
• v.18 no.2
• /
• pp.220-227
• /
• 2014

This paper presents a control method of Single-Inductor Dual-Output DC-DC Converter using Common mode feedback and differential feedback loops. To generate duty used for differential mode feedback loop, this paper propose relative sawtooth circuit using current divider circuit which makes ramp signal with variable dead-time. Two outputs of the Single-Inductor Dual-Output DC-DC Converter are specified for 2.8 V and 4.2 V with input voltage 2.5 V. The maximum conversion efficiency of designed SIDO DC-DC Converter is 95% at total output power of 539mW. Cross regulations of Boost1 and Boost2 are 3.57% and 4% each, when increasing twice times output current.

• Structural Engineering and Mechanics
• /
• v.6 no.2
• /
• pp.125-141
• /
• 1998

Recent test results of steel moment connections repaired with a haunch on the bottom side of the beam have been shown to be a very promising solution to enhancing the seismic performance of steel moment-resisting frames. Yet, little is known about the effects of using such a repair scheme on the global seismic response of structures. When haunches are incorporated in a steel moment frame, the response prediction is complicated by the presence of "dual" panel zones. To investigate the effects of a repair on seismic performance, a case study was conducted for a 13-story steel frame damaged during the 1994 Northridge earthquake. It was assumed that only those locations with reported damage would be repaired with haunches. A new analytical modeling technique for the dual panel zone developed by the author was incorporated in the analysis. Modeling the dual panel zone was among the most significant consideration in the analyses. Both the inelastic static and dynamic analyses did not indicate detrimental side effects resulting from the repair. As a result of the increased strength in dual panel zones, yielding in these locations were eliminated and larger plastic rotation demand occurred in the beams next to the shallow end of the haunches. Nevertheless, the beam plastic rotation demand produced by the Sylmar record of 1994 Northridge earthquake was still limited to 0.017 radians. The repair resulted in a minor increase in earthquake energy input. In the original structure, the panel zones should dissipate about 80% (for the Oxnard record) and 70% (for the Sylmar record) of the absorbed energy, assuming no brittle failure of moment connections. After repair, the energy dissipated in the panel zones and beams were about equal.