• Korean Chemical Engineering Research
• /
• v.50 no.6
• /
• pp.1049-1055
• /
• 2012

The fiber mat catalytic burner that uses infrared radiative heat obtained by flameless catalytic combustion was manufactured and tested to investigate its combustion characteristics. About 9 to 17% of combustion heat was released by sensible heat during the premixed catalytic combustion depend on combustion condition. To find out radiation intensity with distance between catalytic burner and sample, the equation that calculate the receiving surface of radiative energy under the fiber mat catalytic burner was driven. This equation was well correlated with the drying rate of melamine. The drying experiments were carried out to the melamine, wood chip and agricultural pallet by using the fiber mat catalytic burner and the energy efficiency was calculated from drying rate of them. The energy efficiency of the fiber mat catalytic burner reaches to 79% in maximum for drying of the wood chip.

• Journal of Biosystems Engineering
• /
• v.2 no.2
• /
• pp.37-45
• /
• 1977

Solar energy is a potential source of power that offers much promise being used for low-temperature applications like drying farm crops, space heating, and water heating for domestic uses. Already much of it are being used for those purpose in foreign countries. However, very little research has been done to determine the possibility of using the solar energy in Korea. This study was conducted to develop the general prediction equation of the total radiation on a horizontal surface in Daejeon area based on 5 years 91972, Jun.1-1976. Dec.31) meteorological data (bright sunshine hours, average total horizontal radiation), and to obtain experimentally the thermal efficiency of solar air and water collectors, which will be used as a basic data of designing flat-plate solar collector system.In addition to the thermal efficiency of the collectorsthe relationship among those factors affecting it such as weather condition, orientation factor, and tilted angle of collector was analyzed. The results of this study were as follows. 1. The general predicted equation of the total radiation on a horizontal surface in Daejeon area based on bright sunshine hours was developed as $H_{av} =(1.546\frac{n}{N}-0.582)H_o$. Predicting the total radiation on a horizontal surface by the above equation was thought to be possible because to values of 0.882 was smaller than any t values at above 0.05 level on the basis of two tailed test of the difference between the calculated and the recorded values. 2.It was observed that optimum tilt angle of the collector in the summer and the autumn drying season was 13 degrees and 51 degrees respectively, these values could be obtained by adding or substracting approximately 25 degrees from the latitude of this area $(36.3^{\circ}N)$ .The relationship between orientation factor and declination of sun at suitable tilt angle of 33 degrees $(s=0.9\O)$ was shown at Fig.4. 3.The thermal efficiency of solar wdter collector was shown 13.4-51. 6% on Aug. 15 (the minimum radiation recorded) and 43.8 ~537% Aug.20 (the maximum radiation recorded), and 13.8~ 46.6 and 44.3~ 49.7 were shown on each corresponding day. 4.The thermal efficiency of the collectors according to the weather condition was shown a big difference of about 10% between the day of the maximum radiation recorded and the minimum, but the differen of efficiency between the air and the water collector was at most 2 ~ 3%. 5. Even if the efficiency of the solar water collector was a little higher than the solar air collector, for drying farm products, the solar air collector was thought to be more effective because the air heated by collector could be directly used for drying them.

• Korean Journal of Materials Research
• /
• v.24 no.8
• /
• pp.429-433
• /
• 2014

As the fabrication technology used in FPDs(flat-panel displays) advances, the size of these panels is increasing and the pattern size is decreasing to the um range. Accordingly, a cleaning process during the FPD fabrication process is becoming more important to prevent yield reductions. The purpose of this study is to develop a FPD cleaning system and a cleaning process using a two-phase flow. The FPD cleaning system consists of two parts, one being a cleaning part which includes a two-phase flow nozzle, and the other being a drying part which includes an air-knife and a halogen lamp. To evaluate the particle removal efficiency by means of two-phase flow cleaning, silica particles $1.5{\mu}m$ in size were contaminated onto a six-inch silicon wafer and a four-inch glass wafer. We conducted cleaning processes under various conditions, i.e., DI water and nitrogen gas at different pressures, using a two-phase-flow nozzle with a gap distance between the nozzle and the substrate. The drying efficiency was also tested using the air-knife with a change in the gap distance between the air-knife and the substrate to remove the DI water which remained on the substrate after the two-phase-flow cleaning process. We obtained high efficiency in terms of particle removal as well as good drying efficiency through the optimized conditions of the two-phase-flow cleaning and air-knife processes.

• Journal of Pharmaceutical Investigation
• /
• v.37 no.2
• /
• pp.113-117
• /
• 2007

The aim of this study was to investigate the effect of different wall material on the microencapsulation efficiency of microcapsules containing fish oil. The present work reports on the microencapsulation of fish oil by spray drying using hydroxypropyl methylcellulose (HPMC) 2910, maltodextrin, gelatin, sodium caseinate as wall materials. The emulsion stability was assessed by emulsion stability index value (ESI). The microstructural properties of microcapsules was evaluated by scanning electron microscopy (SEM) and microencapsulation efficiency (ME) was assessed by soxhlet method. The highest ESI and ME were observed in the case of a 1:1 gelatin/sodium caseinate ratio and 1:1 glycerin fatty acid ester/lecithin ratio, and ME of microcapsules was increased with increasing the ESI of emulsion. Thus, the stability of emulsion was a critical factor for the encapsulation of fish oil.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.926-936
• /
• 1996

Field hulling of high-moisture paddy followed by brown rice drying offers many advantages over the present paddy harvesting and drying offers many advantages over the present paddy harvesting and drying system. We did a preliminary study of the parameters for efficient hulling of high-moisture paddy using the IRRI Centrifugal Huller and two India rice varieties. Hulling capacity , hulling efficiency , brown rice recovery and percent whole bown rice were generally best at the impeller peripheral speed of 44m/s. A second pass through the huller increased hulling capacity , brown rice revery and hulling efficiency, but reduced percent whole brown rice. To solve this , we recommed separation of paddy after hulling and aspiration such that only unhulled and partially -hulled grains will be fed back to the huller. Paddy at even 23% m.c. could be effectively hulled by the impeller-type huller , but the results were generally better at 14 to 17% m.c. Only in percent whole brown rice did the 17 to 23% m.c. range performed better than that of 14% m.c. Difference invarietal response to hulling was observed.

• Journal of Pharmaceutical Investigation
• /
• v.31 no.4
• /
• pp.257-263
• /
• 2001

The microspheres have been developed as a new drug delivery system. Although many particulate drug carriers, such as liposome, niosome and emulsion, have been introduced, injectable and biodegradable microspheres appears to be a particularly ideal delivery system because the local anesthesia is not necessary for the insertion of large implants and for the removal of the device after the drug release is finished. Biodegradable microspheres with nicotine and triamcinolone acetonide are prepared and evaluated. As biodegradible polymers, PLA (M.W. 15,000, PLA-0015), PLGA (M.W. 17,000, RG 502) and PLGA (M.W. 8,600, RG 502H) are used. This study attempted to prepare and evaluate the nicotine and triamcinolone acetonide-incorporated microspheres, which were prepared by two methods, solvent-evaporation and spray-drying methods. The microspheres, as a disperse system for injections, were evaluated by particle size, size distribution, entrapment efficiency, and in vitro drug release patterns. The differences of preparation method, partition coefficient, types of polymer, and preparation conditions of microspheres influence the particle size, entrapment efficiency, and in vitro drug release patterns.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.18 no.3
• /
• pp.259-266
• /
• 1998

A field experiment was carried out to determine the effects of mechanical and chemical drying agents at mowing on the field drying rate and hay quality of orchardgrass dominant pasture plants. The mower conditioner /chemical drying agent ($K_2CO_3$ 2% conditioning, $K_2CO_3$ 2% + conditioning and control) were treated at different harvest stages (late boot, heading and bloom stage) for hastening hay manufacture in 1996. After field dry, four square bales were made by hay baler, and the visual estimation and nutritive value of hay were evaluated after storing two months. The field drying rate of pasture plants was higher with delayed stage of harvest, and mechanical and mechanical + chemical, but chemical alone was very low. In mower conditioning, the duration of field dry was shortened by 0.5 to 1 day compared with $K_2CO_3$ and 1.5 to 2 days compared with control. The dry matter loss of hay was reduced by late harvest and mechanical, and mechanical + chemical, but the score by chemical alone was very low. The visual score (leafiness, green color, odor and softness) of hay after storage was high in mechanical and mechanical + chemical, but the score by chemical alone was very low. Nutritive value (ADF, NDF, digestibility, and relative feed value) of hay was also high with treatment of mechanical and mechanical + chemical, but the quality by chemical alone was similar compared with control. The quality of hay was very low when harvested at bloom stage. In conclusion, mower conditioning can enhance the field drying rate of orchardgrass dominant pasture plants, however the drying efficiency of chemical drying agent was very low. Harvesting at early heading to heading stage was recommened for manufacture of high quality hay.

• Korean Chemical Engineering Research
• /
• v.54 no.3
• /
• pp.374-379
• /
• 2016

When using an ionic liquid as co-solvent, the extraction efficiency of anticancer agent paclitaxel from biomass was dramatically improved. However, the residual ionic liquid had a significant negative effect on convenient and feasibility of following concentration and drying steps. In this study, a novel method was developed for the effective drying of the crude extract obtained from biomass extraction with ionic liquid. The residual ionic liquid was easily and conveniently removed by drying alone after pre-treatment and additional washing of a sample with water. The optimal crude extract/water ratio and mixing time for pre-treatment and crude extract/water ratio for additional washing were 1:70 (w/v), 4 min, and 1:100 (w/v), respectively. In the microwave-assisted drying process, the drying time was 9-fold shorter than in the vacuum oven drying process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.249-257
• /
• 2004

Drying and curing characteristics of PCM resins using the induction heater and short-wave infrared emitter module was studied to develop a compact oven system for the high speed CCL and post-treatment equipment. Drying of the polyester resins using the induction heater and infrared heater showed that the blistering tendency of polyester resin coating increased regardless of additives and colors of resins as the heating rate and/or dry film thickness increased. The blistering of polyester resin coating layer occurred when the heating speed was over than $25^{\circ}C/sec$ for the dry film thickness of $19\~20um$, which is the typical thickness of finish coating in CCL. So did it when the heating speed was over than $40^{\circ}C/sec$ for the dry film thickness over than 10 um. The heating efficiency of paint coated steels by the infrared heating was strongly dependent on the colors of paint coating and generally increased for the dark surface and/or coating. But the faster drying of the PCM resin coatings increased the blistering tendency of coating layer. The blistering limit for the typical finish coating by the infrared heating was estimated as the heating rate slower than $20^{\circ}C/sec$ regardless of colors of PCM resins.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.1
• /
• pp.35-41
• /
• 1995

Persimmon boards of 30mm thick were dried, their temperatures were monitored during drying with 490 and 200watt microwave, and the drying efficacy and problems were investigated. The effects of pretreatments such as presteaming and prefreezing were also examined. The persimmon green lumbers of 80% moisture content were dried to 10% for only 50~60 and 110 minutes with 49watt and 200watt microwave, respectively. Severe internal checks were, however, found in all boards. The presteamed boards collapsed on their surfaces earlier than the controls. It may attribute to the high temperature inside boards during microwave drying and the decrease of their internal tensile strength caused by the presteaming treatment. To increase the internal tensile strength of the pretreated boards and to reduce their internal checks, they were air-dried at room temperature. The air-dried boards could be dried to 10% moisture content clearly and free from defects with 200watt microwave. The heating efficiency were also calculated with the maximum weight loss per minute of 490watt and 200watt.