• Korean Journal of Agricultural Science
• /
• v.42 no.4
• /
• pp.439-446
• /
• 2015

Kimbugak is one of Korea's traditional snacks made of laver. This study was conducted to investigate the physical drying and frying characteristics of kimbugaks made by a pasting & garnishing machine. The drying and frying characteristics should be analyzed to develop a continuous operation system for manufacturing kimbugak because kimbugak has a high moisture content after pasting process. Materials for pasting and garnishing on laver were rice gruel and sesame. The aluminum shelf with square hole was selected as a drying shelf. The recommended size of the square hole type was $1.5mm{\times}1.5mm$ because characteristics of deformation and easy separation from the shelf were excellent at the hole size. The drying time of 2 hours was also recommended with the drying temperature of $70^{\circ}C$ based on the test results such as dried condition (good), moisture conten t (3.7%), deformation (12.1 mm), and shrinkage rate (19.8%). As the frying conditions for dried kimbugaks, recommended oil temperature and frying time were $170^{\circ}C$, 15 seconds, respectively when corn oil was used. In the case of frying for undried kimbugaks, recommended oil temperature and frying time were $210^{\circ}C$, 2 - 3 minutes, respectively for improvement of work efficiency.

• Korean Journal of Food Science and Technology
• /
• v.25 no.4
• /
• pp.313-320
• /
• 1993

A sublimation model of the freeze drying process, which accounted for the removal of free water, was presented and used to study the operation conditions of freeze driers for carrot juice. It was found that the shortest drying time was obtained when the condenser temperature and chamber pressure were kept at heir lowest values and the plate temperature was controlled independently so that the scorch and melting constraints were both held throughout the drying period. The effect of sample thickness on the drying time was significant. Optimal policies were investigated experimentally in laboratory freeze dryer.

• Journal of Biosystems Engineering
• /
• v.36 no.4
• /
• pp.273-278
• /
• 2011

This study was carried out to define the optimum drying conditions for Lycium chinense Miller as a useful healthy food, because recently the cultivation area and yield of this fruit are increased. The experiments of two varieties were performed at the temperature of $45^{\circ}C$, $50^{\circ}C$, $55^{\circ}C$ and $60^{\circ}C$. The drying ratio was the slowest and quality was the best at the drying temperature of $45^{\circ}C$. The drying temperature was higher, drying ratio was more faster and the quality became worse. The difference of drying ratios between the varieties was insignificant. The energy consumption per hour was the minimum at the drying temperature of $45^{\circ}C$, but the total energy consumption was the maximum for the long drying time. Also, the energy consumption at the drying temperature $50^{\circ}C$, $55^{\circ}C$ and $60^{\circ}C$ was not very different from others. Considering the drying ratio, quality and energy consumption, the drying time of 36 hours at the drying temperature of $50^{\circ}C$ was the most optimum condition.

• Korean Journal of Materials Research
• /
• v.23 no.10
• /
• pp.592-598
• /
• 2013

Graphene oxide powders prepared by two different drying processes, freeze drying and spray drying, were studied to compare the effect of the drying method on the physical properties of graphene oxide powder. The graphene oxide dispersion was prepared from graphite by chemical delamination with the aid of sulfuric acid and permanganic acid, and the dispersion was further washed and re-dispersed in a mixed solvent of water and isopropyl alcohol. A freeze drying method can feasibly minimize damage to the sample, but it requires a long process time. In contrast, spray drying is able to remove a solvent in a relatively short time, though this process requires exposure to a high temperature for a rapid evaporation of the solvent. The powders prepared by freeze drying and spray drying were characterized and compared by Raman spectroscopy, X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy, and by an elemental analysis. The graphene oxide powders showed similar chemical compositions; however, the morphologies of the powders differed in that the graphene oxide prepared by spray drying had a winkled morphology and a higher apparent density compared to the powder prepared by freeze drying. The graphene oxide powders were reduced at $900^{\circ}C$ in an atmosphere of $N_2$. The effect of the drying process on the properties of the reduced graphene oxide was examined by SEM, TEM and Raman spectroscopy.

• The Korean Journal of Health Service Management
• /
• v.11 no.4
• /
• pp.203-211
• /
• 2017

Objectives : This study aims to design a method for drying forceps jars. As part of the process, holes were made in the forceps jars. Drying time, rate of wet pack, and cost of rewashing linen were then determined. Moreover, the study looked into the bacteria incidence rate in the forceps jars. This study suggests a practical way for preventing infection in a hospital through a surgical device. Methods : This study investigated the effect of forceps jars with holes on reducing drying time, rate of wet pack, and cost of rewashing linen. It also looked into the bacteria incidence rate in the forceps jars through a parallel design. Data was collected and analyzed using SPSS version 21. Results : The drying time of a forceps jars was remarkably reduced from $18.44{\pm}0.2$ minutes(non-hole forceps jars) to $0.58{\pm}0.02$ minutes(4-hole forceps jars). The rate of wet pack of non-hole forceps jars was 51.4%. However, the rate of 4-hole forceps jars reached 4.6%. The cost of rewashing linen saw a decline from 38,073 won to 3,381 won. In addition, no bacteria and virus were detected from the 24-hours usage of forceps jars even though the jars had holes. Conclusions : The 4-hole forceps jars greatly increased work efficiency as a result of the reduced drying time, rate of wet-pack and cost of rewashing linen. The 4-hole forceps jars did not influence their sterilizing effect.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.4
• /
• pp.427-434
• /
• 2000

In tradition, there have been two kinds of drying methods, which are sun drying and artificial drying. The sun drying method which has been adopted traditionally has been replaced by the hot-air drying method which is one of the most general methods of artificial drying, with its simple drying system, low initial cost of drying plant, and easy operating method. But the hot-air drying method has some defects; (1) much energy loss happens due to the discharge of hot air during the drying process, (2) control of drying rate is not easy on account of changing relative humidity of inlet air for uniform hot air temperature, (3) high temperature of foods in drying process brings about the production of low-grade drying products. Vacuum drying takes advantage of energy saving and mass production because it reduces the drying time by increasing the drying rate under low temperature condition. The aim of this paper is to develop the low temperature vacum dryer, with low initial investments and operating costs, easy operating method and trouble-free operation.

• Journal of Pharmaceutical Investigation
• /
• v.40 no.3
• /
• pp.161-166
• /
• 2010

A fast dissolving tablet was developed using the freeze-drying technique. Hyeonggaeyeongyotang was selected as a model oriental medicine. Formulation and processing parameters were studied to obtain freeze-dried tablet with high drug loading, good palatability, and fast disintegration time. $Kollidon^{(R)}$ CLM served as both matrix former and taste masking agent. Ethanol used as co-solvent, decreased the disintegration time of tablet. Aspartame was employed to impart better taste. Drying condition was found to have a major effect in the morphology of the tablets. Freeze-drying process was optimized to decrease the processing time and improve the appearance of the tablets.

• Journal of Biosystems Engineering
• /
• v.6 no.1
• /
• pp.83-92
• /
• 1981

A simulation model of natural air drying to predict the changes of the grain moisture content and dry matter loss of rough rice was developed by the application of mass diffusion theory. A series of simulated drying tests was conducted using the 10 year weather data (1970-1979) obtained from Cheongju, Chuncheon, Daegu, Daejeon, Jeonju, Jinju and Suweon in Korea. System performance factors treated in this study were initial moisture content, airflow rate, bin diameter and grain depth. The results obtained in this study are summarized as follows: 1) The simulation model used in this study was validated with actual experimental results and was applicable to the natural air drying of rough rice. 2) Minimum airflow rates for safe drying were determined for different initial moisture contents and regional weather conditions as shown in Table 6. 3) Equations for estimating drying time and dry matter loss in terms of airflow rate and initial moisture content were derived in the form of an exponential function. 4) These results show that the natural air drying system of rough rice is feasible in Korea even for the poorest drying condition.

• Food Science of Animal Resources
• /
• v.42 no.3
• /
• pp.411-425
• /
• 2022

Semi-dried restructured sausages are restructured meat products with a high nutritional and economic value. However, excessively long drying times can have negative effects on the energy consumption, texture, and sensory properties of semi-dried restructured sausages. The objective of this study was to investigate the effects of different water contents on the drying and physicochemical characteristics of semi-dried restructured sausages. Sausages were prepared with different initial moisture contents (0%-50%) and drying time (0-580 min). The drying characteristics, including the drying rate, effective moisture diffusivity, and water activity of sausage were significantly improved as the initial moisture content was increased. When the initial moisture content of the sausage was 50%, physicochemical properties, such as color, porosity, shear force, and volatile basic nitrogen, were improved the most along with the decreased drying time. Scanning electron microscopy data showed greater porosity and pore size in sausages with the increase of initial moisture content. Collectively, our data suggest that an increase in the initial moisture content of semi-dried restructured sausages improves their drying characteristics and physicochemical properties.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.3
• /
• pp.24-30
• /
• 1981

This experiment was carried out to determine the drying time from green to oven dry and estimate the moisture content of wood, such as red lauan (Shorea Spp.), Douglas fir (Pseudotsuga menziesii), Birch (Betula platyphylla), and oak (Quercus aliena), at various thickness, paralleled to fiber, of specimen for M.C. by oven dry method (100-105$^{\circ}C$). The results obtained are summarized as follows: 1. The drying time from green to oven dry decreases as the thickness of specimen for M.C. becomes to be thined, and that time at 10mm thickness are 14 hrs, for birch wood and 24 hrs, for oak wood. 2. The relative formulae between thickness (X) of specimen for M.C. and drying lime (Y) from 12% to oven dry are showed in Fig. 3. 3. The M.C. based on the weight of specimen for M.C. at t% can be obtained from the formula (2), and the drying time to 1% are shorter than that time to oven dry by approximately three times.