• The Journal of the Acoustical Society of Korea
• /
• v.41 no.5
• /
• pp.589-600
• /
• 2022

In order to verify the reliability of Dry Test Bench (DTB) used for testing the output energy from ballistic extracorporeal shock wave therapeutic devices, the measurements with DTB were compared with the acoustic energy measured with a Laser Doppler Vibrometer (LDV) for a commercial ballistic ESWT device. It was shown that the mechanical energy detected with DTB had variability maintained within 5 % at the same output power setting and also had a linear correlation (adj. R² = 0.991) with the acoustic energy measured with the LDV for the entire output power settings. Using the correlation between the two methods and the correlation on the acoustic energy measured in between air and water with the LDV, the DTB measurement can be used to estimate the energy flux density in water with an average error of 7.85 % for the entire output power settings of the ballistic shock wave generator considered in the experiment. DTB provides information limited to the output mechanical energy and therefore it is not suitable for testing the various acoustic output parameters required in IEC61846 and IEC63045. However, DTB that is simple in measurement principles and easy to use is expected for manufacturers and clinical users to monitor the performance of ballistic Extracorporeal Shock Wave Therapy (ESWT) devices.

• International Journal of Automotive Technology
• /
• v.3 no.4
• /
• pp.171-176
• /
• 2002

A bench test set-up is employed to simulate the friction characteristics of a paper-based friction material operating against a steel plate. Dry friction tests are run as well as tests with transmission fluids. Glazed friction material produces a negative coefficient of friction versus sliding velocity (f-v) curve for both dry friction and lubrication with transmission fluids. At low sliding speeds, the coefficient of friction when operating in transmission fluids for glazed friction materials is greater than that under dry friction. An appreciable negative f-v slope occurs at low sliding speeds for glazed friction materials when running with the transmission fluid. The friction material after running in produces a constant f-v curve under dry friction and a negative slope when lubricated with transmission fluid. At low sliding speeds, the coefficient of friction of the run-in friction material is lower than that of the glazed wet material. On the other hand, the run-in friction material has a larger friction coefficient than does the glazed friction material at higher sliding speeds.

• Journal of Drive and Control
• /
• v.12 no.1
• /
• pp.1-8
• /
• 2015

The stability of friction characteristics and thermal management for a dry type dual clutch transmission (DCT) are inferior to those of a wet clutch. Too high temperature resulting from frequent engagement of DCT speeds up degradation or serious wear of the pressure plate or burning of the clutch disk lining. Even though it is significantly important to estimate the temperature of a dry double clutch (DDC) in real-time, few meaningful study of the thermal model of DDC has been known yet. This study presented a thermal analytical model of lumped parameters for a DDC by analyzing its each component firstly. Then a series of experimental test was carried out on the test bench with a patented temperature telemetry system to validate the proposed thermal model. The thermal model, whose optimal parameter values were found by optimization algorithm, was also simulated on the experimental test conditions. The simulation results of DDC temperature show consistency with the experiment, which validates the proposed thermal model of DDC.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1998.11a
• /
• pp.97-105
• /
• 1998

The goal of this study is to investigate the potential application of triboelectrostatic separation process for removing unburned carbon from fly ash. The process utilizes the difference in electrical charging characteristics between the organic material (carbon) and the mineral matter (fly ash). In the present work, dry separation tests have been conducted on Samchunpo fly ash samples using a bench - scale analytic separator. The test variables studied include air rate, feed rate, electric field strength, particle size, charger material and length, etc. The best separation results were obtained at the air rate 501/min, feed rate 15 g/min and voltage 15 ㎸. The fly ash with carbon content below 1 % was obtained with over 65% recovery.

• Textile Coloration and Finishing
• /
• v.25 no.2
• /
• pp.134-139
• /
• 2013

A tenter is very important to dry and heat-set fabrics in textile dyeing and finishing industry. However, the tenter machine typically utilizes more than 80% of all the power in dyeing system, and yet is one of the primary machine which affects quality of fabrics. Therefore, performance optimization of the tenter machine is required to reduce energy consumption and enhance quality of fabrics. To optimize the tenter machine, it is important to maintain the uniform flow rate, which can be obtained by optimizing a nozzle geometry. In this study, emboss hole angle was investigated as main parameter in flow rate uniformity and heat flux efficiency. The analysis results were compared with those acquired from bench-scale dryer test in the laboratory. The tenter machine performance simulated by Computational Fluid Dynamics(CFD) was optimized by controlling emboss hole angle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.134-141
• /
• 2005

Semi-Spherical Continuously Variable Transmission(SS-CVT) is the CVT which transmits power by rolling friction between dry metals, and its outstanding advantage is the ability of realizations of neutral, forward and reverse states without relying on any other devices. A spherical shaped variator transmits power and also changes gear ratio where keeping contact with a output disk. The frictional direction to transmit power and the other direction to change gear ratio are perpendicular to each other, so we can describe that two dimensional rolling friction is occurred in the contact point between the variator and the disk. Since magnitudes or relations of the two forces are completely unknown, they were analyzed by the experiments in this study. We determined the variables related with the friction phenomena by the dimensional analysis, and manufactured the SS-CVT test bench which could measure the related variables. Finally, the empirical formula for evaluating the two friction forces was proposed based on the experimental results.