• 한국음향학회지
• /
• 제41권5호
• /
• pp.589-600
• /
• 2022

탄도형 체외 충격파 치료기의 출력 에너지를 측정하는 Dry Test Bench(DTB)의 신뢰성을 검증하기 위해, 상용 탄도형 충격파 치료기에 대해 Laser Doppler Vibrometer(LDV)로 측정된 충격파의 음향 에너지와 비교했다. 실험 결과, DTB로 측정된 역학적 에너지는, 동일한 출력 설정에서, 5 % 이내의 변동성을 보이며, 치료기의 전 출력 설정 범위에서 LDV로 측정된 충격파의 음향 에너지와 선형적인 상관성(adj. R² = 0.991)을 확인했다. 두 측정 방법의 상관성과, LDV을 이용하여 공기 및 수중에서 측정된 충격파 음향 에너지의 상관성(adj. R² = 0.995)을 통합하면, DTB 측정으로부터 수중에서 발생된 충격파의 energy flux density를 평균 7.85 % 오차로 추정된다. DTB는 치료기의 출력에너지에 대한 정보만 제공하기 때문에, IEC61846 및 IEC63045에서 요구하는 다양한 충격파의 음향 출력을 시험하는 도구로 적합하지 않다. 그러나 측정 원리가 단순하고 사용이 용이한 DTB는 제조사 및 사용자가 탄도형 Extracorporeal Shock Wave Therapy(ESWT) 치료기의 성능을 관리하는 목적으로 유용하게 사용될 수 있을 것으로 기대된다.

• International Journal of Automotive Technology
• /
• 제3권4호
• /
• pp.171-176
• /
• 2002

A bench test set-up is employed to simulate the friction characteristics of a paper-based friction material operating against a steel plate. Dry friction tests are run as well as tests with transmission fluids. Glazed friction material produces a negative coefficient of friction versus sliding velocity (f-v) curve for both dry friction and lubrication with transmission fluids. At low sliding speeds, the coefficient of friction when operating in transmission fluids for glazed friction materials is greater than that under dry friction. An appreciable negative f-v slope occurs at low sliding speeds for glazed friction materials when running with the transmission fluid. The friction material after running in produces a constant f-v curve under dry friction and a negative slope when lubricated with transmission fluid. At low sliding speeds, the coefficient of friction of the run-in friction material is lower than that of the glazed wet material. On the other hand, the run-in friction material has a larger friction coefficient than does the glazed friction material at higher sliding speeds.

• 드라이브 ㆍ 컨트롤
• /
• 제12권1호
• /
• pp.1-8
• /
• 2015

The stability of friction characteristics and thermal management for a dry type dual clutch transmission (DCT) are inferior to those of a wet clutch. Too high temperature resulting from frequent engagement of DCT speeds up degradation or serious wear of the pressure plate or burning of the clutch disk lining. Even though it is significantly important to estimate the temperature of a dry double clutch (DDC) in real-time, few meaningful study of the thermal model of DDC has been known yet. This study presented a thermal analytical model of lumped parameters for a DDC by analyzing its each component firstly. Then a series of experimental test was carried out on the test bench with a patented temperature telemetry system to validate the proposed thermal model. The thermal model, whose optimal parameter values were found by optimization algorithm, was also simulated on the experimental test conditions. The simulation results of DDC temperature show consistency with the experiment, which validates the proposed thermal model of DDC.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 1998년도 공동 심포지엄 및 추계학술발표회
• /
• pp.97-105
• /
• 1998

The goal of this study is to investigate the potential application of triboelectrostatic separation process for removing unburned carbon from fly ash. The process utilizes the difference in electrical charging characteristics between the organic material (carbon) and the mineral matter (fly ash). In the present work, dry separation tests have been conducted on Samchunpo fly ash samples using a bench - scale analytic separator. The test variables studied include air rate, feed rate, electric field strength, particle size, charger material and length, etc. The best separation results were obtained at the air rate 501/min, feed rate 15 g/min and voltage 15 ㎸. The fly ash with carbon content below 1 % was obtained with over 65% recovery.

• 한국염색가공학회지
• /
• 제25권2호
• /
• pp.134-139
• /
• 2013

A tenter is very important to dry and heat-set fabrics in textile dyeing and finishing industry. However, the tenter machine typically utilizes more than 80% of all the power in dyeing system, and yet is one of the primary machine which affects quality of fabrics. Therefore, performance optimization of the tenter machine is required to reduce energy consumption and enhance quality of fabrics. To optimize the tenter machine, it is important to maintain the uniform flow rate, which can be obtained by optimizing a nozzle geometry. In this study, emboss hole angle was investigated as main parameter in flow rate uniformity and heat flux efficiency. The analysis results were compared with those acquired from bench-scale dryer test in the laboratory. The tenter machine performance simulated by Computational Fluid Dynamics(CFD) was optimized by controlling emboss hole angle.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.134-141
• /
• 2005

Semi-Spherical Continuously Variable Transmission(SS-CVT) is the CVT which transmits power by rolling friction between dry metals, and its outstanding advantage is the ability of realizations of neutral, forward and reverse states without relying on any other devices. A spherical shaped variator transmits power and also changes gear ratio where keeping contact with a output disk. The frictional direction to transmit power and the other direction to change gear ratio are perpendicular to each other, so we can describe that two dimensional rolling friction is occurred in the contact point between the variator and the disk. Since magnitudes or relations of the two forces are completely unknown, they were analyzed by the experiments in this study. We determined the variables related with the friction phenomena by the dimensional analysis, and manufactured the SS-CVT test bench which could measure the related variables. Finally, the empirical formula for evaluating the two friction forces was proposed based on the experimental results.