• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.692-696
• /
• 2011

A clutch is a very important component when engine starts and gear shifting is needed. The clutch the most commonly used is the dry clutch. This type of clutch has pads, and they are worn after disengagement of clutch little by little. The characteristics of the clutch changes as these pads wear, so wear needs to be measured, and the clutch should be controlled for proper operation. In this study, the clutch contact point estimation algorithm has been developed. From this algorithm, clutch force map changes depending on wear, and the clutch operates properly. We also see the shifting transient of a vehicle for drivability with throttle valve position control and synchronizer movement.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.372-378
• /
• 2016

Clutch torque control is the key to the ride comfort improvement of a vehicle equipped with AMT (automated manual transmission). For such control, the torque transfer starting point, known as the "kiss point," should be indicated or at least estimated to compensate for the clutch torque. The kiss point changes due to wear, high temperature, and fatigue; as such, it should be estimated while the vehicle is being driven. In this study, the method of kiss point active estimation for an AMT vehicle with a dry-type clutch was devised. The kiss point is learned while the engine is in an idle state and while the transmission is at a neutral gear position. It is determined when the input shaft of the transmission starts to rotate by slowly engaging the clutch. The noise of the shaft speed signal during the slow engagement process is filtered for accurate control. The kiss point estimation at various clutch engagement speeds was analyzed via a vehicle test.

• 드라이브 ㆍ 컨트롤
• /
• 제12권1호
• /
• pp.1-8
• /
• 2015

The stability of friction characteristics and thermal management for a dry type dual clutch transmission (DCT) are inferior to those of a wet clutch. Too high temperature resulting from frequent engagement of DCT speeds up degradation or serious wear of the pressure plate or burning of the clutch disk lining. Even though it is significantly important to estimate the temperature of a dry double clutch (DDC) in real-time, few meaningful study of the thermal model of DDC has been known yet. This study presented a thermal analytical model of lumped parameters for a DDC by analyzing its each component firstly. Then a series of experimental test was carried out on the test bench with a patented temperature telemetry system to validate the proposed thermal model. The thermal model, whose optimal parameter values were found by optimization algorithm, was also simulated on the experimental test conditions. The simulation results of DDC temperature show consistency with the experiment, which validates the proposed thermal model of DDC.

• 한국생산제조학회지
• /
• 제24권3호
• /
• pp.287-293
• /
• 2015

With the rise in oil prices and ongoing concerns about environment, there is an increased amount of interest in automated manual transmission (AMT) vehicles. Torque control in an AMT vehicle is attained by controlling the displacement of the dry-type clutch's actuator. To provide good ride comfort akin to that of an automatic transmission vehicle, the clutch control is vital to an AMT vehicle. In this study, a method of obtaining the clutch torque from a dynamometer test is devised. This method is able to identify the relationship between the displacement of the clutch actuator and the clutch torque. A simulator for estimating the performance of an AMT vehicle is developed using MATLAB Simulink. The results obtained from both the vehicle and simulation exhibit a similar trend.

• Tribology and Lubricants
• /
• 제30권5호
• /
• pp.265-270
• /
• 2014

Frictional heat greatly influences the friction behaviors during clutch engagement. Therefore, the engagement of a wet or dry clutch is frequently not under control by the frictional heat. In a wet clutch, the frictional temperature also specially needs to be controlled, and in many cases, the clutch material is selected to prevent a temperature rise from the friction between friction pad and separator. However, only the selection of the clutch material cannot ensure sufficient control of the temperature rise by the friction. The groove pattern on a friction pad is designed for more flow rates of transmission fluid between the contact gap of clutch pad and separator for the cooling effect. In this work, grove patterns are designed for more flow rates out of the contact gap between friction pad and separator plate. Selected groove design shows the improvement flow rates of transmission fluid through both inner and outer radius, where most of the transmission fluid flows through the outer radius when the clutch is engaged due to the centrifugal force in conventional wet clutch groove. Several comparisons of the amounts of frictional heat generated on clutch pads are made in order to verify the decrease of the temperature rise according to the flow rates along the groove patterns.

• 한국자동차공학회논문집
• /
• 제11권5호
• /
• pp.112-118
• /
• 2003

The friction coefficients of the rubber for clutch master cylinder were experimentally measured in this study. The cylindrical rubber samples for primary cup-seal and secondary cup-seal were tested against the aluminum or the steel plates of master cylinder housing under the various conditions of brake oil temperatures and normal loads. Dry sliding friction coefficients were also measured under various load conditions. The test revealed following results. First, the friction coefficient under fluid lubrication condition in general decreases, as the oil temperature or normal load increases. Second, the steel plate of low surface roughness yielded comparatively low friction coefficient on the range of 0.30∼0.67. On the other hand, the aluminum plate of high surface roughness yielded high friction coefficient on the range of 0.31∼1.15. Third, the friction coefficient of dry surface contact decreases as the normal load increases. This is contrary to the general principle of friction coefficient between metal plates.

• 한국자동차공학회논문집
• /
• 제3권3호
• /
• pp.79-89
• /
• 1995

Rattle noise occurs at manual transmission as idling and driving of a automotive. It can be solved by torsional characteristics of a clutch disc. A clutch disc consist of a region of pre-damper and main-damper. Rattle noise is affected by pre-damper and main-damper equipped for a torsional spring and friction washer. Pre-damper range covers noise radiating from manual transmission when engine is idling and main-damper range covers noise when engine is driving. The aim of this reserch is to clear transmission rattle noise by way of torsional characteristics of a clutch disc. The experiment is carried out as idling and driving of a automobile equipped for 1.5L MPI engine, dry single-disc type clutch and manual transmission. In this study, the results show for a vibration of manual transmission as idling and driving can be cleared by a clutch disc of Pre-damper type.

• 한국산학기술학회논문지
• /
• 제21권5호
• /
• pp.77-83
• /
• 2020

오늘날 자동차 산업의 기술 발전으로 4륜구동 기술이 승용차에도 적용되고 있으며, 이를 위해 트랜스퍼 케이스용 건식 다판클러치가 사용되고 있다. 하지만 건식 클러치의 경우 진동에 대한 문제가 발생하여 승차감에 영향을 주게 된다. 이를 해결하기 위해 4륜 구동장치의 핵심부품인 트랜스퍼케이스에 있는 다판클러치의 체결시 발생하는 충격을 저감시키고자 MR유체가 적용된 다판클러치를 제안한다. MR 다판클러치는 유체커플링 모드와 압착모드를 가지게 되며, 최적 설계를 위해 토크모델을 유도하였다. 다판클러치의 설계변수를 최적화를 위해 Ansys Maxwell을 이용하여 해석을 수행하였고, 전자기장 해석은 디스크와 플레이트의 수를 변경하였을 때 자기장의 세기를 확인하였으며, 자기장의 세기는 최대 0.45 Tesla가 도출되었다. 이를 토크방정식에 적용하여 플레이트 사이 간격을 2mm로 플레이트의 내경과 외경을 각각 45mm와 55mm로 선정하였다. 이와 같이 본 논문에서는 MR 다판클러치의 성능을 극대화할 수 있는 최적 설계기법을 제안하였다.

• 한국가스학회지
• /
• 제19권3호
• /
• pp.49-53
• /
• 2015

이 논문의 목적은 자동차 클러치, 수동변속기와 타이어 시스템의 마찰에 관련된 화재에 대한 고장사례를 분석하고 연구하는 것이다. 첫 번째 사례는 반복적으로 클러칭하면서 자동차의 클러치 디스크가 플라이 휠의 접촉면과 접촉하면서 열에 의해 과열되어 이 열이 수동변속기의 외부로 흘러 고착된 오일 찌꺼기에 옮겨 붙어 화재가 발생된 것으로 확인되었다. 두 번째, 사례로 변속 장치는 기어와 기어의 접촉에 의해 동력을 전달한다. 변속기 오일이 변속기 케이스의 균열로 인해 오일 부족 현상이 일어나 변속기 케이스 상단의 퇴적물에 의해 화재가 발생된 것을 확인하였다. 세번째 사례는 건조한 구덩이에서 빠져나오려고 반복적으로 가속페달을 작동시키면서 타이어와 도로의 마찰이 반복되면서 내부의 축적된 열에 의해서 화재가 발생된 것으로 확인되었다. 따라서, 운전자는 운전 중 마찰부에 화재가 발생하지 않도록 세심하게 관리하여야 한다.

• Journal of Ecology and Environment
• /
• 제31권3호
• /
• pp.201-206
• /
• 2008

This study was conducted to determine clutch size and habitat usage of Kentish plovers (Charadrius alexandrinus) breeding on Sinja-do lslet in the Nakdong Estuary from 22 April to 12 July in 1995 and from 21 April to 20 June in 1996. The Kentish plover preferred grasslands and damp sands to dry dunes as nesting sites. The difference in hatching success among these microhabitats was attributed to high tides, which washed away many nests on damp sands, and strong winds, which frequently shifted the sand to bury eggs on dry dunes. The main mortality factor in grasslands was predation by magpies Pica pica. Each clutch contained one to four eggs, with a mode of three eggs. Hatching success was highest in two-egg clutches and lowest in one- and four-egg clutches. The mean interval for egg laying was 1.8 days between the first and second eggs and 2.1 days between the second and third eggs. The average incubation period was about 24.2 days.