• International Journal of Highway Engineering
• /
• v.5 no.2 s.16
• /
• pp.1-14
• /
• 2003

This study is a fundamental research for developing self-deicing function of snow-melting asphalt concrete for roadway pavement. The objective of this study is to develop technology of making self-snow-melting asphalt pavement and evaluate properties of the asphalt concrete containing deicers. Asphalt concrete with deicers and CRM was produced by dry process. The $\alpha$-deicer, CRM and F-deicer were used for sand asphalt mixtures of thin-layer pavement on the existing pavement. The $\alpha$-deicer, $\beta$-deicer, CRM A, CRM B and C were used for 13mm dense-graded mixtures on surface course. Penetration grade of 60-80 asphalt was used for asphalt mixtures. Marshall mix-design, indirect tensile strength, freezing and thawing test, analysis of extracted water were carried out to evaluate performance of self deicing function of asphalt mixtures. The study result showed that snow-melting asphalt mixtures had not only good mechanical characteristics and good snow-melting function, but also chemically safe in environmental point of view.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.21-30
• /
• 2015

PURPOSES : The purpose of this study was to evaluate the performance of rapid-setting polymer-modified asphalt mixtures with a high reclaimed asphalt pavement (RAP) content. METHODS: A literature review revealed that emulsified asphalt is actively used for cold-recycled pavement. First, two types of rapid-setting polymer-modified asphalt emulsion were prepared for application to high-RAP material with no virgin material content. The quick-setting polymer-modified asphalt mixtures using two types of rapid-setting polymer-modified asphalt emulsion were subjected to the following tests: 1) Marshall stability test, 2) water immersion stability test and 3) indirect tensile strength ratio test. RESULTS AND CONCLUSIONS : Additional re-calibration of the RAP was needed for laboratory verification because the results of analyzing RAP aggregates, which were collected from different job sites, did not deviate from the normal range. The Marshall stability of each type of binder under dry conditions was good. However, the Type B mixtures with bio-additives performed better in the water immersion stability test. Moreover, the overall results of the indirect tensile strength test of RAP mixtures with Type B emulsions exceeded 0.7. Further research, consisting of lab testing and on-site application, will be performed to verify the possibility of using RAP for minimizing the closing of roadways.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.109-114
• /
• 2007

Skid mark and coefficient of friction are usually utilized to calculate the velocity and behavior of vehicles. For a critical case such as traffic accident reconstruction, however, the initial velocity of the car should be calculated precisely. In this study, the skid marks on dry asphalt pavement were measured, and the velocity at brake onset was precisely recovered. A passenger car with new tires and non-contact optical speedometer were set up for the tests. A new methodology to determine the more precise velocity for Non-ABS vehicle at braking onset were suggested.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1998.10a
• /
• pp.180-185
• /
• 1998

The study was conducted to evaluate the fundamental properties of waste tire asphalt concretes using polymer modified hinder that were made by dry process. The specimens of four types of polymer modified asphalt concretes were prepared, then Marshall test and indirect tensile strength tests were performed on these samples. The results showed that polymer modified waste tire rubber asphalt concrete was acceptable for the material of asphalt pavement surface layer.

• International Journal of Highway Engineering
• /
• v.17 no.5
• /
• pp.1-10
• /
• 2015

PURPOSES : A finite difference model considering snow melting process on porous asphalt pavement was derived on the basis of heat transfer and mass transfer theories. The derived model can be applied to predict the region where black-ice develops, as well as to predict temperature profile of pavement systems where a de-icing system is installed. In addition, the model can be used to determined the minimum energy required to melt the ice formed on the pavement. METHODS : The snow on the porous asphalt pavement, whose porosity must be considered in thermal analysis, is divided into several layers such as dry snow layer, saturated snow layer, water+pavement surface, pavement surface, and sublayer. The mass balance and heat balance equations are derived to describe conductive, convective, radiative, and latent transfer of heat and mass in each layer. The finite differential method is used to implement the derived equations, boundary conditions, and the testing method to determine the thermal properties are suggested for each layer. RESULTS: The finite differential equations that describe the icing and deicing on pavements are derived, and we have presented them in our work. The framework to develop a temperature-forecasting model is successfully created. CONCLUSIONS : We conclude by successfully creating framework for the finite difference model based on the heat and mass transfer theories. To complete implementation, laboratory tests required to be performed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.52-59
• /
• 2008

Most accident reconstruction or analysis depend on the coefficient of friction to estimate the vehicle speeds. Skid mark and coefficient of friction are usually utilized to calculate the velocity and behavior of vehicles. For a critical case such as traffic accident reconstruction, however, the initial velocity of the car should be calculated precisely. In this paper, emergency brake tests on ABS and Non-ABS brake system are conducted on the dry pavement asphalt road on speed 40, 60, 80 and 100 km/h respectively. The SWIFT sensor was established in the front wheel and rear wheel at driver side to measure the forces, moments and speeds of revolution of the tires. These tests results can be available to brake tests and accident reconstruction.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.6
• /
• pp.54-62
• /
• 2010

The scientific analysis of car-pedestrian accidents is not an easy task because of the characteristic of the accidents itself. Since the analysis involved human being, there were few experimental data that could be used for the analysis. The coefficient of friction of human body was the one of crucial data for accident analysis, but no field experiment report was available for various roadway conditions. This study intends to measure the coefficient of friction of human body through field studies. Results showed that the coefficient of friction of human body for dry asphalt pavement conditions was 0.59~0.62, and for dry concrete pavement conditions was 0.59~0.61. In addition, the coefficients for wet asphalt pavement and for wet concrete pavement conditions were 0.56~0.59 and 0.51~0.54 respectively, indicating 5.0% and 8.3% reduction compared to the dry conditions. The deduced coefficients were validated using the simulation program. It has been confirmed that the experiment values were close to the simulation results.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.59-67
• /
• 2012

This study presents the evaluation of the patching materials that are used to repair the distress of asphalt pavement. Four kinds of patching materials currently used in practice were tested in both laboratory and field. The laboratory tests included the dry and soaked Marshall stability test, indirect tensile test, wheel tracking test and adhesive strength between the asphalt pavement and the repairing material was tested as a performance test. The field study was conducted using the slab samples placed on the location of vehicle tire passing and the performance of the repairing materials were investigated as passing the traffic load. The result of the laboratory tests were satisfied with the current design criteria and material standard except for water-immersion stability. Type C patching material showed the highest adhesive shear strength among the patching materials tested. However, the mature distress, such as rutting and stripping were monitored after construction in 10 days. It was found that performance of patching material is lack of quality behavior when they were applied in the field and required to develop and applu to prevent the mature distress of the current patching materials.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.183-188
• /
• 1997

From a viewpoint of construction cost and preserving management of pavement, a policy of domestic pavement was gradually spreaded concrete pavement rather than asphalt. But the use of concrete with ordinary portland cement has shortages, such as dry-shrinkage, low flexural strength, etc. In order to overcome these problems, the concrete pavement using CSA expansive additive (Non-Shrinkage Cement) was studied and carried out the fie이 application. As the results, we find out Non-Shrinkage Cement that was distinguished in short-term construction by increasing flexural strength, shrinkage compensating and low-heat evaluation compared with OPC concrete.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.205-219
• /
• 2008

The polymers, low-density polyethylene (LDPE) and styrene-butadiene-styrene(SBS) -modified asphalt mixtures are advanced asphalt pavement materials in which $3{\sim}6%$ of them, and/or some other additive, by weight of total binder are added. The purpose of modifying asphalt material is to improve typical weakness such as rutting and cracking resistance of normal asphalt mixtures. These materials have been proved to show many advantages and practical applicability in the plant and field. Wet processed PMA binder and/or dry processed asphalt mixtures are developed as field products for many years. The objective of this paper is to show the characteristics of the LDPE and SBS-modified asphalt mixtures by comprehensive evaluation and comparison with those of normal asphalt mixtures.