• Journal of the Korean Geotechnical Society
• /
• v.29 no.4
• /
• pp.45-56
• /
• 2013

In this study, a blast furnace slag with latent hydraulic property is used to cement granular soils without using Portland cement. When the blast furnace slag reacts with an alkaline activator, it can cement soils. The effect of amounts of blast furnace slag and types of alkaline activator on soil strength was investigated for resource recycling. Four different amounts of slag and six different activators (two naturals and four chemicals) were used for preparing specimens. The specimens were air-cured for 3 or 7 days and then tested for unconfined compressive strength (UCS). The UCS of cemented sand with slag increased, in the order of specimens mixed with potassium carbonate, calcium hydroxide, sodium hydroxide and potassium hydroxide. Chemical alkaline activator was better than natural alkaline activator. The maximum UCS of 3-days cured specimens was 3 MPa for 16% of slag with potassium hydroxide, which corresponded to 37% of one with 16% of high-early strength portland cement. As the amount of slag increased, the UCS and dry density of a specimen increased for all alkaline activator cases. As the curing time increased from 3 days to 7 days, the UCS increased up to 97%. C-S-H hydrates were found in the cemented specimens from XRD analyses. Cement hydrates were more generated with increasing amount of slag and they surrounded sand particles, which resulted in higher density.

• Journal of the Korea Concrete Institute
• /
• v.25 no.4
• /
• pp.457-465
• /
• 2013

This study discussed the influence of mixtures and curing conditions on the development of strength and microstructure of RPC using ternary pozzolanic materials. Through pilot experiment, various RPC was manufactured by adding single or mixed ternary pozzolanic materials such as silica fume, blast furnace slag and fly ash by mass of cement, up to 0~65%, and cured by using 4 types of method which are water and air-dried curing at $20^{\circ}C$, steam and hot-water curing at $90^{\circ}C$. The results show that the use of ternary pozzolanic materials and a suitable curing method are an effective method for improving development of strength and microstructure of RPC. The unit volume of cement was greatly reduced in RPC with ternary pozzolanic materials and unlike hydration reaction in cement, the pozzolanic reaction noticeably contributes to a reduction in hydration heat and dry shrinkage. A considerable improvement was found in the flexural strength of RPC using ternary pozzolanic materials, and then the utilization of a structural member subjected to bending was expected. The X-ray diffractometer (XRD) analysis and Scanning Electronic Microscope (SEM) revealed that the microstructure of RPC was denser by using the ternary pozzolanic materials than the original RPC containing silica fume only.

• The Journal of the Korea Contents Association
• /
• v.14 no.4
• /
• pp.389-396
• /
• 2014

This study was conducted as the basic research for the replacement of Blast Furnace Slag, Red Mud, Silica Fume, etc., with cement as a solution to the problems arising from the global warming caused by the generation of $CO_2$, and conducted the experimental review to examine the feasibility of matrix having properties identical to those of cement by using the Blast Furnace slag, Red mud, Silica fume, and alkali-activator. For this, by using the the inorganic binder, such as Blast Furnace Slag, Red Mud, Silica Fume, etc., and NaOH, $Na_2SiO_3$ and others as the cement substitute material, the strength characteristic according to the mixture time variation was performed in the tentative experiment. Based on the preceding experiment, this study performed the experiment to analyze the strength properties of hardener through the curing by air-dry temperature, curing by temperature in water, coating curing, and Korean paper curing. For the water curing at $80^{\circ}C$, the compressive strength and flexural strength were found to be the most excellent at the age of the 28th day, and furthermore, it was found that the non-cement hardener could be made, which is considered to affect the production of eco-friendly concrete.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.1
• /
• pp.93-101
• /
• 2014

In this study, a blast furnace slag having latent hydraulic property with an alkaline activator for resource recycling was used to solidify sand without using cement. Existing chemical alkaline activators such as $Ca(OH)_2$ and NaOH were used for cementing soils. An alkaliphilic microorganism, which is active at higher than pH 10, is tested for a new alkaline activator. The alkaliphilic microorganism was added into sand with a blast furnace slag and a chemical alkaline activator. This is called the microorganism alkaline activator. Four different ratios of blast furnace slag (4, 8, 12, 16%) and two different chemical alkaline activators ($Ca(OH)_2$ and NaOH) were used for preparing cemented specimens with or without the alkaliphilic microorganism. The specimens were air-cured for 7 days and then tested for the experiment of unconfined compressive strength (UCS). Experimental results showed that as a blast furnace slag increased, the water content and dry density increased. The UCS of a specimen increased from 178 kPa to 2,435 kPa. The UCS of a specimen mixed with $Ca(OH)_2$ was 5-54% greater than that with NaOH. When the microorganism was added into the specimen, the UCS of a specimen with $Ca(OH)_2$ decreased by 11-60% but one with NaOH increased by 19-121%. The C-S-H hydrates were found in the cemented specimens, and their amounts increased as the amount of blast furnace slag increased through SEM analysis.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.10
• /
• pp.1364-1373
• /
• 2012

Four crossbred (75% Holstein Friesian) lactating dairy cows, with an average live weight of $418{\pm}5$ kg and $36{\pm}10$ d in milk were randomly assigned according to a $2{\times}2$ factorial arrangement in a $4{\times}4$ Latin square design to evaluate the effects of cassava hay (CH) and rice bran oil (RBO) on feed intake, nutrient digestibility, ruminal fermentation, milk yield, and milk composition. Factor A was non-supplementation or supplementation with CH in the concentrate. Factor B was supplementation with RBO at 0% or 4% in the concentrate mixture. The four dietary treatments were (T1) control (Concentrate with non-CH plus 0% RBO; C), (T2) Concentrate with CH plus 0% RBO (CH), (T3) Concentrate with non-CH plus 4% RBO (RBO), and (T4) Concentrate with CH plus 4% RBO (CHRBO). The cows were offered concentrate, at a ratio of concentrate to milk production of 1:2, and urea-lime treated rice straw was fed ad libitum. Urea-lime treated rice straw involved 2.5 g urea and 2.5 g $Ca(OH)_2$ (purchased as hydrated lime) in 100 ml water, the relevant volume of solution was sprayed onto a 100 g air-dry (91% DM) straw, and then covering the stack with a plastic sheet for a minimum of 10 d before feeding directly to animals. The CH based concentrate resulted in significantly higher roughage intake and total DM intake expressed as a percentage of BW (p<0.05). Ruminal pH, $NH_3$-N, BUN and total VFA did not differ among treatments, while RBO supplementation increased propionate, but decreased acetate concentration (p<0.05). Furthermore, the population of total ruminal bacteria was significantly lower on the RBO diet (p<0.05). In contrast, the total ruminal bacteria and cellulolytic bacteria on the CH diet were higher than on the other treatments. Supplementation with CH increased (p<0.05) F. succinogens and R. flavefaciens populations, whereas the populations of B. fibrisolvens and M. elsdenii were increased on the RBO diet. In addition, supplementation with CH and RBO had no effect on milk production and composition in dairy cows, while fatty acid composition of milk was influenced by RBO supplementation, and resulted in significantly lower (p<0.05) concentrations of both short-chain and medium-chain FA, and increased (p<0.05) the proportion of long-chain FA in milk fat, as well as significantly increased cis-9, trans-11 CLA and total CLA. In conclusion, RBO or CH exhibited specific effects on DMI, rumen fermentation, microbial population, milk yield and composition in lactating dairy cows, which were not interactions between CH and RBO in the diets. Feeding lactating dairy cows with RBO could improve fatty acid in milk fat by increasing cis-9, trans-11 CLA.

• Journal of Bio-Environment Control
• /
• v.27 no.2
• /
• pp.111-116
• /
• 2018

This study were carried out to evaluate the efficiency of using burn-type $CO_2$ generators in greenhouse for cultivation 'Seolhyang' strawberry ($Fragaria{\times}ananassa\;Duch.$) during winter season. The concentration of $CO_2$ was 200 to $600{\mu}mol{\cdot}mol^{-1}$ in the control, and 800 to $1,100{\mu}mol{\cdot}mol^{-1}$ in using burn-type $CO_2$ generator between 6 and 11 hours. At other times, it was observed that at similar concentration in the control and using burn-type $CO_2$ generator. Measured greenhouse air temperature inside the of using burn-type $CO_2$ generator was $2{\sim}3^{\circ}C$ higher than the control at 6 ~ 10 am. There was no temperature difference between treatments after 11 o'clock. Plant height, leaf length, leaf width, root diameter, fresh weight, and dry weight were not different between treatments. The marketable yield (kg/10a) of using burn-type generator were 4,131 kg, which was 519 kg higher than the control. Therefore, the total fruit yields increased 17% compared to the control.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.760-766
• /
• 2016

This study explored the effects of heating temperature and laminae thicknesses on the time required to heat the center of air-dried Paulownia tomentosa, Pinus sp., Abies sp., and Larix sp. laminae to $56^{\circ}C$, which is a minimum core temperature of wood packaging materials defined by ISPM 15 standard, and maintain for 30 minutes in dry heat treatment schedule. Heating times were different among wood species and were Pinus sp. ${\geq}$ Abies sp. > Paulownia tomentosa > Larix sp. in decreasing order. The differences in heating times of some species were significantly different statistically, but were not different enough in practical terms to warrant heating four species separately. Heating times decreased as heating temperature increased and followed approximately power-function relationship. Also, heating times increased linearly with increasing laminae thickness. These relationships make it possible to calculate intermediate heating times relative to experimentally observed heating times. The results of this study will serve as a guideline for heat sterilization of Chinese laminae species to meet heat treatment requirements for protection against invasive pests.

• The Korean Journal of Quaternary Research
• /
• v.18 no.2 s.23
• /
• pp.103-104
• /
• 2004

This paper discuss some results of observed changes of meteorological elements as temperature, precipitation and some extreme indexes in Mongolia. Mongolia is one of the largest landlocked countries in the world. The climate is characterized by a long lasting cold winter, dry and hot summer, low precipitation, high temperature fluctuation and relatively high number of sunny days per year. During last 60 years the annual mean air temperature has risen $1.66^{\circ}C$. Intensive warming of > $2^{\circ}C$ was observed at higher altitudes of high mountains when warming of < $1^{\circ}C$ was observed the Domod steppe and the Gobi Desert. Heat Wave Duration have statistically significant risen trend with increaded number of days by 8-18 at significance level of 95-99.9% depending on geography and Cold Wave Duration have shortened by 13.3 days significance level of 95-99%. In general, by the amount of precipitation, Mongolia falls in semi-arid and arid region. It is 300-350 mm in the high mountain regions while it is only 50-150 mm in Gobi Desert regions. The changes of annual precipitation have very localized character i.e.decreasing at one site and increasing at a sit nearby. Annual precipitation decreased by 30-90 mm in the northern-central region and increased by 2-60 mm in the western and eastern region. The magnitude of alteration changes in precipitation regardless increasing or decreasing is 5-25%. A trends, significant at the level of 90%, found where changes are more than 40 mm or more than 15% of annual mean value. Moreover, the soil moisture resources was decreased in the last 40 years. Specially, moisture contents of the top soil have decreased 2 times(N. Natsagsuren, 2002). Months of June and July in Mongolia is the year that moisture is not inhibiting vegetation growth. Unfortunately, its also found that moisture in this time tends to decrease. Increased temperature, decreased precipitation and soil moisture are most likely resulted in occurences of more intense drought spells that have taken place during the recent years. Intimately, these changes have considerable impact on livestock in Mongolia.

• Geotechnical Engineering
• /
• v.7 no.4
• /
• pp.49-64
• /
• 1991

Abstract The stabilization by lime or Portland cement has long been the most commonly used methods for clay soil. But it wart the purpose of this reserch to define the effectiveness malt content on unconfined compressive strength of limeflay mixture and cementrlay mixture. From result of a laboratary investigation, saInt content in sample soil was not concernd with variation of PH value. PH value of lime 10% mixture and of cement 10% mixture were near 12.4, 11.6 respectively. In case of more than 7 curing days, PH value and Ca++ion concentration were decreased with increasing curing time. Also the result of X-ray difflection analysib for stabilized soil by admixture 10% in 90 curing days showed that the diffrection intensity of Tobermorite and Ettringite and other reaction products was smaller in the case of addition of salt 8% than malt 0% in stabilized soil. When lime-soil mixture and cement-boil mixture were cured in 2$0^{\circ}C$ and 5$^{\circ}C$, 2$0^{\circ}C$ cured mizture produced significantly higher compressive strength than 5t cured mixture and air dry curing sample produced higher than cured sample in water. The addition of salt 2~4% in conjuntion with lime or cement may accelerate strenth gain or not prevent front However, the addition of salt 8% prevent from strength gams.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.71-78
• /
• 2012

Recycled aggregates are made from construction wastes, and they have many national and social benefits by saving energy, developing substitute resources, and protecting environment. However, low-quality recycled aggregate with low density and high absorption rate cannot be used for structural concrete aggregate but is used mainly for low added value. Therefore, this study aims to identify the characteristics of the materials of recycled aggregates made after crashing and pulverizing waste concrete. For this, their major physical characteristics of cement content, absolute dry density, absorption rate, etc. were reviewed to make a mix design (draft) for the production of the secondary product and performance evaluation was done on the bending strength, absorption rate, bending strength after freezing and thawing, compressive strength, air-dried gravity, etc. of the test products produced by applying the mix design to compare the results with the quality standards of GR mark. The results of the tests showed that the substitution rate of recycled aggregate increased to 50~90 %, which is of superior quality than the performance standards of GR F 4007. Therefore, it is thought that they can be used for various construction works with certain physical characteristics applicable to the production of secondary concrete products using recycled aggregates.