• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.8
• /
• pp.1068-1076
• /
• 1997

Emission control of acid exhaust gases from coal-fired power plants and waste incinerators has become an increasing concern of both industries and regulators. Among those gaseous emissions, SO$_{2}$ has been eliminated by a Spray Drying Absorber (SDA) system, where the exhaust gas is mixed with atomized limestone-water slurry droplets and then the chemical reaction of SO$_{2}$ with alkaline components of the liquid feed forms sulfates. Liquid atomization is necessary because it maximizes the reaction efficiency by increasing the total surface area of the alkaline components. An experimental study was performed with a laboratory scale SDA to investigate whether the scrubbing efficiency for SO$_{2}$ reduction increased or not with the application of a DC electric field to the limestone-water slurry. For a selected experimental condition SO$_{2}$ concentrations exited from the reactor were measured with various applied voltages and liquid flow rates. The applied voltage varied from -10 to 10 kV by 1 kV, and the volume flow rate of slurry was set to 15, 25, 35 ml/min which were within the range of emission mode. Consequently, the SO$_{2}$ scrubbing efficiency increased with increasing the applied voltage but was independent of the polarity of the applied voltage. For the electrical and flow conditions considered a theoretical study of estimating average size and charge of the atomized droplets was carried out based on the measured current-voltage characteristics. The droplet charge to mass ratio increased and the droplet diameter decreased as the strength of the applied voltage increased.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.641-646
• /
• 2016

The effects of water addition on $Y_2O_3$ coatings or thick films prepared by plasma suspension spray (SPS) have been investigated. Water addition in suspension media was found to be effective to control the color of a $Y_2O_3$ coating prepared by SPS. The color changed with water addition at the shortest stand-off distance of 50 mm even if samples had the same crystalline phase. Change was not correlated with fragmentation behavior of liquid suspension inside the plasma jet. Water content over 50 vol% was found to produce unmelted particles, indicating that water suppressed heat transfer to the particles. However, plasma jet temperature was not affected. Instead, the coating fabricated with water addition has higher oxygen and lower carbon content compared to these characteristics of the coating without water addition. This was attributed to the retarded complete evaporation of liquid media from the suspension droplet, resulting in inhibition of excessive heating and evaporation of the molten $Y_2O_3$ droplet. In this regard, crystalline phase development with respect to stand-off distance and water addition was discussed.

• Journal of the Korea Institute of Building Construction
• /
• v.4 no.1
• /
• pp.97-103
• /
• 2004

In case of a fire in road or railway tunnel it is always necessary to keep the escape condition as good as possible. Most of the victims of major fires in tunnels are because they couldn't leave the tunnel in time and were trapped by smoke, or rescue teams couldn't reach the place of the accident due to low visibility and high temperature. In spring 2003 a comprehensive field experiment was undertaken in a large scaled tunnel in Youngin City to test the effectiveness of a new water spray curtain system, designed to the air qualify inside of a tunnel in case of fire during passenger's escape to safe routes, In order to control the smoke propagation, fixed water sprayed nozzles were used to make water curtain system, which can be installed or hanging water piping line below ceiling. The experiment was accompanied by an extensive measurement campaign in order to measure temperature dropping effect and flow conditions as well as CO concentration for various water sprayed curtains produced by sprinkler heads or water spray nozzle. Eventually comparison analysis were undertaken to investigate the performance of water curtains under fixed water pressure. Therefore most effective water curtain system was presented on the basis of water droplet size in long tunnel.

• The Journal of Internal Korean Medicine
• /
• v.39 no.6
• /
• pp.1181-1190
• /
• 2018

Objective: This study investigated the effect of purified medical herb extracts such as Alisma canaliculatum and Polyporus umbellatuson adipogenic differentiation of human bone marrow derived mesenchymal stromal stem cells (hBMSCs). Methods: Two different medical herb were extracted using hot distilled water. The optimal concentration of extracts were fixed at 100 ng/ml by means of cell viability and cytotoxic assay. To test the adipogenic differentiation ability of extracts, we induced the adipogenesis of hBMSCs for 21 days. At day 5, the cell was harvested to check mRNA and protein expression level of adipogenic related factors. The efficacy of lipid droplet formation was evaluated using the oil-red O staining method at days 21. Results: Two different medical herb extracts have no toxicity on hBMSCs. And two different medical herb extracts significantly decreased formation of lipid droplet compared with control groups in hBMSCs. The A. canaliculatum extract group showed the lowest mRNA and protein expression level of adipossgenic related transcription factors. This data suggests that extract of A. canaliculatum and P. umbellata decrease the adipogenic differentiation of hBMSCs. Conclusions: Our findings indicate that water-extract of A. canaliculatum and P. umbellata will be useful therapeutic reagents for prevention of obesity related disease such as diabetes, hyperlipidemia, coronary artery disease, and osteoporosis.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.7
• /
• pp.573-580
• /
• 2021

Paraffin wax is attracting many attentions for promising solid fuel of hybrid rocket because of its higher regression than other fuels. However, even with paraffin fuel combustion, unsteady low-frequency oscillation of combustion pressure is still observed. And, this is related to the formation of liquid layer and the entrainment of fuel droplets entering the axial combustion gas flow. This study investigates the effect of additional combustion of fuel droplets on the occurrence of low-frequency combustion instability. On the other hand, the formation of fuel droplets depends on Weber Number (the ratio of the inertial force to the surface tension of the liquid) and Reynolds Number of the oxidizer flow. Therefore, a laboratory-scale hybrid rocket was used to monitor the occurrence of combustion instability while changing We number. A series of combustion tests were conducted to control We number by changing the oxidizer flow rate or adding LDPE (low density polyethylene) to base fuel. In the results, it was confirmed that there is a critical We number above which the low-frequency combustion instability occurs.

• Journal of Microbiology and Biotechnology
• /
• v.22 no.6
• /
• pp.806-813
• /
• 2012

Adipocyte differentiation is strongly associated with obesity, which causes metabolic disorders. In this study, we investigated the inhibitory effects of widdrol on 3T3-L1 preadipocyte growth and differentiation. Widdrol decreased lipid droplet accumulation and down-regulated adipogenic transcription factors such as C/$EBP{\alpha}$, C/$EBP{\beta}$, and $PPAR{\gamma}$. Widdrol blocked preadipocyte proliferation and differentiation through the inhibition of mitotic clonal expansion, which was accompanied by the failure of degradation of p21, a cyclin-dependent kinase inhibitor. Cell-cycle analysis clearly indicated that widdrol actively induces cell-cycle arrest at the G1-S phage transition, causing cells to remain in the preadipocyte state. Moreover, widdrol increased p21 expression and inhibited Rb phosphorylation in preadipocyte incubated in a hormone medium. Therefore, these findings clearly suggest that widdrol blocks preadipocyte growth and differentiation through the inhibition of mitotic clonal expansion by p21-and Rb-dependent G1 arrest and can be developed as a potent anti-adipogenic agent for reducing obesity.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.5
• /
• pp.55-59
• /
• 2011

Atmospheric plasma technology was utilized in order to modify surface characteristics of base paper for coating. Argon(Ar) and oxygen(O2) gases were used. It was found that contact angle of a water droplet was decreased with increasing voltage during plasma treatment, meaning that the hydrophilicity of paper surface was increased. On the other hand, the physical properties like roughness and optical properties such as gloss, brightness and opacity were not influenced by the plasma treatment. In conclusion, atmospheric plasma technology can be utilized to control hydrophilicity of paper surface without affecting physical properties of the paper.

• Journal of Powder Materials
• /
• v.16 no.1
• /
• pp.56-62
• /
• 2009

The degree of WC decomposition and hardness of thermally sprayed WC-Co coatings are important factors determining the wear resistance of the coatings. In order to minimize the degree of decomposition and to increase hardness, the effects of processing parameters of high velocity oxyfuel(HVOF) spraying on various characteristics of nanostructured WC-12Co coating have been evaluated by an experimental design method. The HVOF sprayed WC-12Co coatings consisted of various carbide phases including WC, $W_2C$ and $W_3Co_3C$, with a much reduced carbon content. The degree of WC decomposition and decarburization was affected by changing barrel length and spray distance. The hardness of WC-Co coatings was strongly related to droplet temperature at substrate, and increased with increasing fuel addition and/or decreasing spray distance. The effective control of processing parameters was discussed in detail for manufacturing a high performance WC-Co coating.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.491-494
• /
• 2002

To assess the electrostatic interaction of surfaces at the triple contact line, the electrostatic field is analyzed by using the finite element method. The Helmholtz free energy is used as a functional which should be minimized under an equilibrium condition. The numerical results are compared with the nonlinear analytical solution for a two-dimensional charged interface and linear solution for a wedge shaped geometry, which shows fairly good agreement. The method is applied to the analysis of electrostatic influence on the contact angle on a charged substrate. The excess free energy found to increase drastically as the contact angle approaches to zero. This excess free energy Plays an opposite role to the Primary electrocapillary effect, as the contact angle gets smaller. This enables an alternative explanation for the contact-angle saturation phenomenon occurring in electrical control of surface tension and contact angle.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.9
• /
• pp.781-786
• /
• 2015

Recently, studies of 3D printing methods have been working in various applications. For example, the powder base method laminates the prints by using a binding or laser sintering method. However, the draw back of this method is that the post process is time consuming and does not allow for parts to be rapidly manufactured. The binding method requires the post process while the time required for the post process is longer than the manufacturing time. This paper proposes a UV curing binding method with an integrated piezo printing head system. The optimization of an arbitrary waveform generation for the control of a UV curable resin droplet was researched, in addition to developed optimized UV curing processes in multi nozzle ink jet heads.