• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.2
• /
• pp.87-97
• /
• 2018

Bus, a major transportation mode, doesn't have a systematical evaluation system for dangerous driving behavior yet. This paper analyzes the characteristics and pattern of bus driving behavior using Digital Tacho Graph(DTG) data on express bus. 8 types of dangerous driving behavior were considered according to timeslot, the day of week and weather condition. As results, rapid acceleration, rapid left right turn and rapid deceleratio accounted for more than 97% and relatively high percentages were shown in dawn, on Friday and on the clear day, respectively. From the statistical analysis, correlation between the dangerous driving types and difference according the timeslot were found, and 3 groups considering the level of the dangerous driving were suggested. This study contributes to setting an efficient and reliable eduction system for using driving simulators.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.9 s.351
• /
• pp.142-148
• /
• 2006

Considering the domestic traffic environment and the increase of traffic accidents, we have been asked to exactly analyze the main causes of accidents for the accident-experienced drivers to be rehabilitated. In this thesis we present the development process and results of a driving simulator using the IPDE method in the interest of safe driving and driving rehabilitation. Through this Driving simulation development the rehabilitated driver has the possibility of experiencing the real driving situation with the driving aptitude and examines the reasons of accidents. Through the examinations the driver has the chance to correct the deformities of driving by choosing the explanatory scenes, and through this process the driver is able to develop the capability to react in the real situation. However this driving simulation system is one of the best developed, depending on weather and road condition the braking distance may change. Therefore the fuzzy rule and neural network have been used in this thesis to solve previously mentioned problem. The simulation exactly calculated the road and weather conditions to adjust the breaking intensity.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1555-1558
• /
• 2008

Various approaches were undertaken by major PDP makers in order to improve the luminous efficacy of the plasma discharge cells. There have been many reports that state that using a high Xe content PDP is one of the most promising key technologies available to improve the luminous efficacy. In the case of the higher Xe content panel, the higher address and sustain voltage were needed to drive the panel under the same reset condition. In this study, a variety of Xe content panels were investigated in order to examine wall voltage transfer behaviors. The transferred wall voltage status after addressing discharge at the same driving condition was analyzed by comparing Vt close curve of high and low Xe content panels. Through this analysis of Vt close curve difference, the driving waveform of a high Xe panel was quantitatively adjusted Under the same address voltage condition, results showed that the amount of the transferred wall voltage and Vt close curve after addressing discharge was matched for the first sustain discharge. Taking these results into consideration, we conclude that the driving waveform for different Xe content panels could be designed for the desired addressing discharge condition and the wall voltage state of the cell could be quantitatively controlled and measured through these approaches.

• Journal of KSNVE
• /
• v.11 no.1
• /
• pp.125-131
• /
• 2001

There is a clearance between the parts of a machine due to design tolerance, manufacturing error, wear, looseness, or misalignment. If the clearance is large, the vibration and noise of the machine is generally large. Therefore, the analysis on the nitration and noise of a machine can tell the clearance of the machine, which reveals the condition of the machine, i.e., the existence of faults and the safety of the machine. The investigation of this kind of research should be on the basis of experimental results. A link mechanism with a clearance at a joint between the coupler and locker is made for the investigation of the condition monitoring of a machine due to clearance. The vibration and sound are measured from the link driving system during the operation. The signals are clarified using line enhancement technique. The noise removed signals are used to develop the dynamic model of the system for a model based fault diagnosis. Also this study showed that the clarified signals can be used for the calculation of the joint forces between the coupler and rocker and for the correlation between the vibration and sound levels and the clearance sizes.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.5
• /
• pp.391-398
• /
• 2014

This paper presents a resonant step-down DC/DC converter to reduce the voltage stresses of a 3-phase inverter module under the three-phase AC utility line condition. Under this condition, a conventional 3-phase inverter module suffers from high voltage stresses as a result of the high rectified DC link voltage; hence, a high-cost high-voltage-rating inverter module must be used. However, using the proposed converter, a low-cost low-voltage-rating inverter module may be adopted to drive the motor even under the 3-phase AC line condition. The proposed converter, which can be realized with small size inductor and low-voltage-rating semiconductor devices, operates at a high-efficiency mode because of the zero-current switching operations of all the semiconductor devices. The operational principles are explained and a design example is provided in the study. Experimental results demonstrate the validity of the proposed converter.

• Journal of the Korea Safety Management & Science
• /
• v.20 no.3
• /
• pp.21-26
• /
• 2018

This paper describes result of a study on safety against a fire of charging cable for mobile phone for vehicle. Combustion on the USB cable in the car was happened while driving. Gas coming from the burning USB cable could be a reason which can make a secondary car accident since the driver also can be embarrassed while driving. In order to prevent a secondary car accident connected on the road, to research a reason why USB cable can emit gas and be burned in charging. We did simulation test with abnormal fault condition for the electronic component on the board in the USB cable. So we get the result from abnormal fault condition simulation test, for instance, shorted test for output terminal of 8 pin switch, shorted test for chip resistor after thermal aging in the condition $25^{\circ}C$, 93 % RH during 48 hours. To analysis the result of all test, Combustion on the USB cable was not the 8 pin but other electrical component such as a chip resistor. Therefore we guess that the reason for USB cable combustion in charging in a car was not 8 pin and a LED but another defective component.

• Journal of the Korean Society of Safety
• /
• v.30 no.6
• /
• pp.132-138
• /
• 2015

This study examined the relative effects of feedback frequency and specificity of Eco-IVIS(eco in-vehicle information system) on the fuel-efficiency and workload. Eighty participants randomly assigned into four experimental groups (high frequency/specific, high frequency/global, low frequency/specific, and low frequency/global feedback) and they drove 16.4Km motorway under the each feedback condition. The dependent variable were fuel efficiency and Drive Activity Load Index which measured participants' subjective ratings of driving workload. The results showed that high frequent feedback was more effective for increasing fuel-efficiency than low frequent feedback, however, there was no significant difference of fuel-efficiency between specific and global feedback. Although, overall DALI score was comparable among four experimental conditions, visual demand score was significant higher under the high frequent feedback condition than low frequent feedback.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.62-69
• /
• 2013

Visual demands associated with in-vehicle display usage and text messaging distract a driver's visual attention from the roadway. To minimize eyes-off-the-road demands, voice interaction systems are widely introduced. Under cognitively distracted condition, however, awareness of the operating environment will be degraded although the driver remains oriented to the roadway. It is also know that the risk of inattentive driving varies with age, thus systematic analysis of driving risks is required for the older drivers. This paper aims to understand the age-related driving performance degradation and visual attention changes under auditory cognitive demand which consists of three graded levels of cognitive complexity. In this study, two groups, aged 25-35 and 60-69, engaged in a delayed auditory recall task, so called N-back task, while driving a simulated highway. Comparisons of younger and older drivers' driving performance including mean speed, speed variability and standard deviation of lane position, and gaze dispersion changes, which consist of x-axis and y-axis of visual attention, were conducted. As a result, it was observed that gaze dispersion decreased with each level of demand, demonstrating that these indices can correctly rank order cognitive workload. Moreover, gaze dispersion change patterns were quite consistent in younger and older age groups. Effects were also observed on driving performance measures, but they were subtle, nonlinear, and did not effectively differentiate the levels of cognitive workload.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.265-272
• /
• 2016

The objective of vehicle aerodynamic design is on the fuel economy, reduction of the harmful emission, minimizing the vibration and noise and the driving stability of the vehicle. Especially for a sedan, the driving stability of the vehicle is the main concern of the aerodynamic design of the vehicle indeed. In this theoretical study, an evaluation algorithm of aerodynamic driving stability of a vehicle was made to estimate the dynamic stability of a vehicle at the given driving condition on a road. For the stability evaluation of a driving vehicle, CFD simulation was conducted to have the rolling, pitching and yawing moments of a model vehicle and compared the values of the moments to the resistance moments. From the case study, it is found that a model sedan running at 100 km/h in speed on a straight level road is stable under the side wind with 45 m/s in speed. But the different results may be obtained on the buses and trucks because those vehicles have the wide side area. From the case study of the model vehicle moving on 100 km/h speed with 15 m/s side wind is evaluated using the numerical algorithm drawn from the study, the value of yawing moment is $608.6N{\cdot}m$, rolling moment $-641N{\cdot}m$ and pitching moment $3.9N{\cdot}m$. These values are smaller than each value of rotational resistance moment the model vehicle has, and therefore, the model vehicle's driving stability is guaranteed when driving 100 km/h with 15 m/s side wind.

• Journal of Korean Institute of Industrial Engineers
• /
• v.40 no.3
• /
• pp.267-274
• /
• 2014

The purpose of this study is to identify a relationship between the time taken and the characteristics of touch key for touch-screen-based in-vehicle information system (IVIS) and to suggest a new Fitts' law formula that is added a driving speed parameter. Many studies already have shown that Fitts' law is well fitted in various devices for primary tasks, but there is no study of Fitts' law for secondary task in dual-task situation. Fitts' law may not be applied to the secondary task as it is, because the secondary task performance can be affected by the amount of attention for the primary task. To verify this, we carried out an experiment that showed whether pointing task to touch-screen-based IVIS during driving is affected by driving speeds or not. In the experiment, 30 people were volunteered for participants and the participants carried out driving task and pointing task on the screen of IVIS simultaneously. We measured the time to point a touch key on IVIS for every condition (3 driving speeds${\times}5$ touch key sizes${\times}7$ distances between steering wheel and touch key). As a result, there was an effect of driving speed on the pointing time. As we extended the index of difficulty of the conventional Fitts' law formula by incorporating driving speed, we established an extended Fitts' law formula for pointing on IVIS, which showed better accordance with dual task situation. This study can be evidence that secondary task performance is affected by degree of concentration on primary task, and the extended Fitts' law formula can be useful to design interfaces of IVIS.