• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.72-77
• /
• 2011

In this paper, we propose effective diagnosis algorithm for hub bearing fault in driving vehicle using acceleration signal and wheel speed signal measured in hub bearing unit or knuckle. This algorithm consists of differential, envelope and power spectrum method. We developed diagnosis system for realizing proposed algorithm. This system consists of input device including acceleration sensor and wheel speed sensor, calculation device using Digital Signal Processor (DSP) and display device using Personal Digital Assistant (PDA). Using this diagnosis system, a driver can see hub bearing fault(flaking) from the vibration in driving vehicle. With early repairing, he can keep good ride feeling and prevent accident of vehicle resulting from hub bearing fault.

• 한국음향학회지
• /
• 제15권1호
• /
• pp.10-16
• /
• 1996

압전초음파모터는 기존의 전자기식모터와는 달리 압전전체가 발생하는 초음파진동에 의한 마찰력으로 회전자의 구동력을 얻는 모터이다. 이는 구조가 간단하고, 저속에서 높은 토오크를 얻을 수 있어 감속기구 없이 직접구동이 가능한 장점이 있어 주목을 받고 있다. 그러나 이 모터는 인가주파수, 인가전압, 2상의 구동신호사이의 위상차 및 구동신호의 duty비 등에 따라 그 특성이 변하므로, 모터를 제어하기 위해서는 이러한 변수들에 대해 정밀한 특성측정이 필요하다. 본 연구에서는 초음파모터의 제작과 함께 컴퓨터인터페이스된 압전초음파모터 평가장치를 개발하였고, 제작한 초음파모터의 특성을 여러 구동변수에 대해 측정하였다. 구동변수들은 모두 디지털로 처리되므로, 초음파모터의 특성측정을 쉽게 할 수 있을 뿐만 아니라, 차후 초음파모터의 디지털제어에 기본 바탕이 된다.

• 전기학회논문지
• /
• 제66권10호
• /
• pp.1540-1546
• /
• 2017

In piezoelectric device applications, it is important to improve a system efficiency because of the low generated power. In this paper, an optimal driving method is proposed to improve a system efficiency for a piezoelectric energy harvesting system. The proposed method considers disappear energy in input capacitors and the converter efficiency according to the input voltage magnitude to minimize energy losses. Experimental results based on various energy generation cases verify that the proposed method significantly improves the system efficiency; the efficiency is approximately 9.97% higher than that of the conventional method.

• 한국산업융합학회 논문집
• /
• 제18권1호
• /
• pp.37-44
• /
• 2015

In the research, we developed a device for cooling the drive section of the gripper of a robot for handling the high temperature material. In this study, By using a Peltier element, the high-temperature material is not affected and driving cylinder is cooled to prevent damage due to high temperatures. Hot part of the Peltier element is towards the robot gripper. Cool part of the Peltier element is towards the driving cylinder. The heat sink portion is made to keep the cooling effect. As the performance result, cooling-test is taken, and their result is satisfy.

• 한국전기전자재료학회논문지
• /
• 제36권4호
• /
• pp.397-402
• /
• 2023

We have developed inverted green phosphorescent organic light emitting diodes (OLEDs) using 1,1-bis[(di-4-tolylamino)phenyl]cyclohexane (TAPC) and bis(carbazole-9-yl)biphenyl (CBP) hole transport layers. The driving voltage, current efficiency, power efficiency, and emission characteristics of devices were investigated. While the driving voltage for the same current density was about 1~2 V lower in the devices with the TAPC layer, the maximum luminance was higher in the device with the CBP layer. The maximum current efficiency and power efficiency were 3.2 and 2.7 times higher in the device with the CBP layer, respectively. The higher efficiency in the CBP device resulted from the enhanced hole-electron balance although weak parasitic recombination takes place in the CBP hole transport layer.

• 한국전기전자재료학회논문지
• /
• 제18권6호
• /
• pp.576-581
• /
• 2005

We fabricated red organic light emitting diodes(OLEDs) utilizing tis(8-hydroxyquinoline) aluminum $(Alq_3)$ doped with $5\%$ of (4-(dicyanomethylene)-2-i-propyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran) (DCJTI) and investigated the driving and modulation characteristics for applying to the electro-optical conversion device. To improve the driving characteristics of red OLEDs, 3 V of offset voltage, which is equal to the turn on voltage, Is applied to the device. Offset voltage enhanced the optical EL output and reduced the rise time of EL waveforms of red OLEDs, and hence the cutoff frequency is increased with increasing applied voltage. The optical pulse of 100 MHz has been obtained from red OLEDs. Therefore, we confirmed that the red OLEDs can be applied to the fields of optical communication as an electro-optical conversion device.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2000년도 학술대회논문집
• /
• pp.60-63
• /
• 2000

In this paper, 7-segment was implemented using AC powder EL. ZnS:Cu and BaTiO3 was used as a phosphor and dielectric respectively. The preparation of phosphor and dielectric layer was performed with screen printing. The implemented system of 7-segment was divided as following; EL display, driving circuit, software for driving. The properties of fabricated devices was measured with EL spectrum and brightness.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.59-64
• /
• 2018

In general, tracked combat vehicles require excellent output performance of a power unit system to drive on special terrains and in extreme environmental conditions. However, high temperature and pressure are readily applied to the coolant hose in the power unit of the vehicles during high-speed driving under extreme road and weather conditions. These driving conditions can cause the separation phenomenon of the coolant hose in the power unit and consequentially engine overheating during driving. Therefore, a newly designed decompression device for the coolant hose has been proposed and manufactured to solve these problems in the present study. To validate of the newly proposed decompression device, the input and output pressures were measured under the before- and after-improvement conditions using experimental methods for different engine RPMs. In addition, the pre-heater temperature was measured under both conditions. From the experimental results, we expect that the current investigation can help to improve the driving performance of tracked combat vehicles.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권4호
• /
• pp.237-246
• /
• 2004

The advantages of the Magnetic Fluid Linear Pump(MFLP) is that this device could Pump the non-conductive. non-magnetic liquid such as Insulin or blood because of the segregation structure of the magnetic fluid and pumping liquid. In this device. the sequential currents are needed to Produce pumping forces so that Pumping Forces and Pumping speed mainly depend on the current Patterns. The excessive forces at Pumping moment could cause the medical shock, and weak forces at intermediate moment could cause the back flow or the pumping liquid. So the ripples of the pumping forces need to be reduced for the medical application. In this research, the driving characteristics in the MFLP by operating current is analysed. The change of magnetic fluid surface according to the driving currents could be obtained be magneto-hydrodynamic analysis so that Pumping fortes could be computed by integration of the surface moving to the pumping direction at each moment. The actual MFLP with 13mm diameter was made and tested for experiments. The effects of driving current and frequency on the pumping forces and pumping speed were analyzed and compared with experimental measurements.

• 자동차안전학회지
• /
• 제12권1호
• /
• pp.33-38
• /
• 2020

Since a diesel vehicle scandal related to the 'A' automobile company was issued in the United States in 2015, many countries have been interested in emission defeat devices. Being embedded in some diesel passenger cars sold in Korea, a defeat device for exhaust gas may have influence on both fuel economy and NOx emissions. In order to examine such effects, we carried out laboratory indoor tests as well as real road driving tests using four models of 'A' automobile company which may employ defeat devices. Those tests were performed observing the test modes of FTP-75, HWFET, and NEDC. Although fuel economy and NOx emissions according to indoor tests comply with the suggested tolerance, the findings in the real road driving tests do not satisfy the tolerance. Along with the results provided in this study, further evaluation may be necessary to investigate the noticeable difference between the indoor and real road tests.