본 논문에서는 Power IC용 저면적 32비트 differential paired eFuse OTP 메모리를 설계하였다. OTP 메모리 셀 어레이에서 행의 개수가 열의 개수보다 더 작은 경우 eFuse 링크의 프로그램 전류를 공급하는 SL (Source Line) 구동 라인을 열 방향으로 라우팅하는 대신 행 방향으로 라우팅하므로 레이아웃 면적을 많이 차지하는 SL 구동회로의 수를 줄이는 differential paired eFuse 셀 어레이 방식과 코어 회로를 제안하였다. 그리고 blowing되지 않은 eFuse 링크가 EM (Electro-Migration) 현상에 의해 blowing되는 불량을 해결하기 위해 RWL (Read Word-Line) 구동 회로와 BL (Bit-Line) 풀-업 부하회로에 V2V ($=2V{\pm}0.2V$)의 regulation된 전압을 사용하였다. 설계된 32비트 eFuse OTP 메모리의 레이아웃 면적은 $228.525{\mu}m{\times}105.435{\mu}m$으로 기존의 셀 어레이 라우팅을 이용한 IP 크기인 $197.485{\mu}m{\times}153.715{\mu}m$ 보다 20.7% 더 작은 것을 확인하였다.
This paper presents an automatic LCD gamma control system using gamma curve optimization. It controls automatically gamma adjustment registers in mobile LCD driver IC to reduce gamma correction error and adjusting time. The proposed gamma system contains Module-Under-Test (MUT, LCD module), PC installed with program, multimedia display tester for measuring luminance, and control board for interface between PC and LCD module. Proposed algorithm and program are applicable for most of the LCD modules. It is realized to calibrate gamma values of 1.8, 2.0, 2.2 and 3.0. The control board is designed with DSP and FPGA, and it supports various interfaces such as RGB and CPU. Developed automatic gamma control system showed significantly reduced gamma adjusting time of 240 sec. and much less average gamma error of 11% than 42h and 27% with conventional manual method. We believe that the proposed system is very useful to provide high-quality LCD and to improve production process.
LED구동회로및 제어회로를 개발하였다. 개발된 LED구동회로는 새로운 PWM회로를 가지고 있으며 LED열의 디밍, 전류 및 온도제어 및 통신 기능을 할 수 있다. 개발된 PWM회로는 기본적인 디지털 논리소자를 사용하여 만들어 질 수 있는 두 개의 링 발진기와 한 개의 카운터로 구성되어 있다. 부가적으로 이 회로는 온-오프 제어 모드, 비상모드, 전력절감모드를 가지고 있으며 직열통신을 이용해서 제어된다. 설계 된 PWM 발생기와 제어회로는 마그나칩/하이닉스의 디지털 공정을 이용하여 제작되었다. 제작된 칩은 LED구동장치와 제어기 보드에 장착되어 테스트 되었으며 성공적으로 동작하였다.
The primary cause of air pollution by vehicles is imperfect combustion of fuel. One of the most usual causes of this imperfect combustion is the misfire in IC(Intenal Combustion) engine. Recently it is obligated for an ECU to monitor the emission level and warn the driver in case of exceeding specified emission standards. Therefore, in order to comply with this OBD-II regulations, car makers are investing a considerable amount into technology which would enable the detection of misfire and the particular cylinder in which misfire is taking place. So far, it has been able to detect misfire using engine speed, which can be obtained crank angle. However, such a method posed a problem in analyzing at high speed and in recognizing the misfire from the load impact at bumpy road. In this paper, misfire detection is made possible by simple arithmetic using WDFT, especially at high engine speed. In addition, the moving window method of a Walsh function is applied to determine the cylinders under misfire in case of multiple misfires. An actual experiment was conducted to prove that WDFT is applicable to effective in computation speed and to same result in misfire detection and cylinder determination at idle, part load and bumpy road conditions.
a-Si(amorphous silicon) TFT(thin film transistor)는 TFT-LCD(liquid crystal display)의 화소 스위칭(switching) 소자로 폭넓게 이용되고 있다. 현재는 a-Si을 이용하여 gate drive IC를 기판에 집적하는 ASG(amorphous silicon gate) 기술이 연구, 적용되고 있는데 이때 가장 큰 제약은 문턱 전압(Vth)의 이동이다. 특히 고온에서는 문턱 전압의(Vth) 이동이 가속화 되고, Ioff current가 증가 하게 되고, 저온($0^{\circ}C$)에서는 전류 구동능력이 상온($25^{\circ}C$) 상태에서 같은 게이트 전압(Vg)에 대해서 50% 수준으로 감소하게 된다. 특히 ASG 회로는 여러 개의 TFT로 구성되는데, 각각의 TFT가 고온에서 Vth shift 값이 다르게 되어 설계시 예상하지 못 한 고온에서의 화면 무너짐 현상 즉 고온 노이즈 불량이 발생 할 수 있다. 고온 노이즈 불량은 고온에서의 각 TFT의 문턱전압 및 $I_D-V_G$ 특성을 측정한 결과 고온 노이즈 불량에 영향을 주는 인자가 TFT의 width와 기생 capacitor비 hold TFT width가 영향을 주는 것으로 실험 및 시뮬레이션 결과 확인이 되었다. 발생 mechanism은 ASG 회로는 AC 구동을 하기 때문에 Voff 전위에 ripple이 발생 되는데 특히 고온에서 ripple이 크게 증가 하여 출력 signal에 영향을 주어 불량이 발생하는 것을 규명하였다.
The world largest 21.3" LTPS LCD has been successfully developed using SLS crystallization technology. Integration of gate circuit, transmission gate and level shifter was successfully performed in a large area display. Uniform and high performance of high quality grains of SLS technology make it possible to realize a uniform large size LTPS TFT-LCD with half the number of data driver IC's that is typically used in a-Si LCD. High aperture ratio of 65 % was achieved using an organic inter insulating method which lead to a high brightness of 500 cd/$cm^2$.
한국정보디스플레이학회 2003년도 International Meeting on Information Display
/
pp.241-244
/
2003
The world largest 21.3" LTPS LCD has been successfully developed using SLS crystallization technology. Successful integration of gate circuit, transmission gate and level shifter was performed in a large area uniformly. Uniformity and high performance from high quality grains of SLS technology make it possible to come true a uniform large size LTPS TFT-LCD with half number of data driver IC's used in typical a-Si LCD. High aperture ratio of 65% was obtained using an organic inter insulating method, which lead a high brightness of 500cd/cm2.
Chip on glass (COG) bonding using anisotropic conductive film (ACF) is a key technology to assemble a driver IC onto a LCD glass panel. In this paper, an experimental investigation was conducted to investigate the correlation between contact resistance and characteristics of image taken by machine vision based inspection system. The results show that the contact resistance was strongly influenced by the contrast ratio of conductive particle rather than the number of conductive particles. Also, number of conductive particles whose contrast ratio is below 0.75 is crucial for determining the quality of the assembled samples. On the other hand, in the result of high temperature high humidity storage test, the contrast ratio of samples was increased. However, in the case of open-circuit samples after temperature humidity storage test, the number of conductive particles whose contrast ratio is above 0.75 was more than that of the closed-circuit samples.
This research attempted simplifications to the LED street light for price competitiveness. The street light was simplified by replacing the SMPS with an IC driver on the PCB using an AC-type LED. The optical element that shape of a line-shaped lens covered LED crowded. Thus, this study aims to improve LED efficiency by using the minimum optical system. In order to satisfy the M3 regulation of street lighting at grade, the lens was divided into two parts depending on the forward direction of the light. Further, the changes in the number of LEDs located on part 1 and part 2 of the lens were analyzed. Through simulation, we determined the proper light distribution that meets M3 regulation of street lighting.
본 논문은 모바일 디스플레이모듈의 signal integrity와 power integrity의 시뮬레이션 방법에 관한 것이다. 본 제안 방법은 커넥터, FPCB, 드라이버IC를 포함하는 회로모듈 해석에 사용할 수 있다. 최근에 모바일 디스플레이 업계의 시리얼 인터커넥션기술에 대한 필요성 대두로 시스템오동작 방지 및 전자기파 발생을 억제하기 위해 신호선과 전원전압에 대한 섬세한 컨트롤이 필요하다. S파라미터와 Z파라미터 분석으로 주파수 도메인과 시간 도메인에서의 상관관계를 분석한다. 멀티포트 매크로를 이용하여 시간 도메인에서 sigh integrity를 power integrity에 함께 분석할 수 있다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.