• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.3
• /
• pp.119-125
• /
• 2004

Generally, it is used the compensation spring to compensate the inaccuracy of screen image induced by thermal deformation in CRT monitor. Its mechanism is bi-metallic system made of heterogeneous metals and these is bonded by laser welding. But laser welding induces the non-uniform temperature distribution and locally residual stress is yielded by these temperature deviation. This paper studies residual stress of laser weldment using FEA and hole drilling method. The results are followed. In the case of heterogeneous materials weldment, higher residual stress induced in the weldment region of SUS 304 which have larger CTE than Ni 36 and residual stress on the middle of specimen is higher by 10.9% than that of its surface Measured residual stress of SUS 304 yield 481MPa and that of Ni 36 is 140.5MPa in the vicinity of the welding region. And the residual distribution is very similar in comparison with FEA result.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.2
• /
• pp.103-111
• /
• 2002

Out of all metal-cutting process, the hole-making process is the most widely used. It is estimated to be more than 30% of the total metal-cutting process. It is therefore desirable to monitor and detect drill wear during the hole-drilling process. One important aspect in controlling the drilling process is monitoring drill wear status. There are two systems, Basic system and Online system, to detect the drill wear. Basic system comprised of spindle rotational speed, feed rates, thrust torque and flank wear measured by tool microscope. Outline system comprised of spindle rotational speed feed rates, AE signal, flank wear area measured by computer vision, On-line monitoring system does not need to stop the process to inspect drill wear. Backpropagation neural networks (BPNs) were used for on-line detection of drill wear. The output was the drill wear state which was either usable or failure. This paper deals with an on-line drill wear monitoring system to fit the detection of the abnormal tool state.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.513-518
• /
• 1999

In this study, geometrical similarity conditions for drills of various diameters are discussed. The effect of geometrical similarity on the chip shape and forces of different sized conventional drills has been experimentally confirmed. Drilling tests are carried out for SM45C by using the conventional HSS drills. The torque and thrust forces are measured and compared with those chip forms. Chip shape in drilling are affected by three factors being flow angle, side and up curl of the chip. It is found that the feedrate and drill diameter are more affected than cutting speed on the chip form and cutting forces. The similarity conditions gives easily to estimate the chip shape, the thrust and the torque for drills of different diameters.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.4 no.1
• /
• pp.18-23
• /
• 2005

This paper reports experimental results on microdrilling process for silicon parts used in semiconductor equipments. An experimental system was developed consisting of a high speed precision machine, microscope system, and project profile instrument. The experimental results indicate that the amount of chipping at the entrance and exit of micro hole decreases as the spindle speed increases up to 18,000 rpm. At higher spindle speed, however, the amount of chipping increases rapidly. The amount of chipping and infeed rate show proportional relationship up to 20 m/min of infeed rate. Beyond that infeed rate, however, sudden increase in the amount of chipping has occurred.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.163-169
• /
• 1999

Residual stresses causing stress corrosion cracking (SCC) of thin-walled steam generator U tubes were investigated. The residual stresses were measured by hole drilling methods, and the applied stresses resulting from the internal pressure and the temperature gradient in the steam generator were estimated theoretically. In U-bent regions, the residual stresses at extrados were induced with compressive stress(-), and its maximum value reached -319MPa in axial direction at $\phi$= $0^{\circ}$ in position. Maximum tensile residual stress of 170MPa was found to be at the flank side at position of $\phi$= $90^{\circ}$, i.e., at apex region. Hoop stress due to the pressure and temperature differences between primary and secondary side were analyzed to be 76 MPa and 45 MPa, respectively.

• IE interfaces
• /
• v.7 no.3
• /
• pp.155-168
• /
• 1994

In computer integrated manufacturing environment, tool management plays an important role in controlling tool performance for machining operations. Knowledge of tool behavior during the cutting process and effective tool-behavior prediction contribute to controlling machine costs by avioding production delays and off-target parts due to tool failure. The purpose of this paper is to review and develop the tool condition monitoring scheme for drilling operation to assure a fast corrective response to minimize the damage if tool failures occur. If one desires to maximize system through-put and product quality as well as tooling resources, within an economic environment, real-time tool sensing system and information processing system can be coupled to provide the necessary information for the effective tool management. The example is demonstrated as to drilling operation when the aluminum composites are drilled with carbide-tipped HSS drill bits. The example above is limited to the situation that the tool failure mode of drill bits is wear.

• Journal of Magnetics
• /
• v.22 no.1
• /
• pp.69-77
• /
• 2017

To empower safe, economical and eco-friendly sustainable solution for enhancing oil and gas productivity from deep water reservoirs, new downhole technologies are recommended. Since electric machine plays leading role in the downhole application, it is a squeezing requirement for researchers to design and develop advanced electric machine. The Recent improvement in technology and uses of high-temperature magnets, permanent magnet flux switching machine (PMFSM) has become one of the appropriate contenders for offshore drilling but fewer designed for downhole due to ambient temperature. Therefore this comprehensive study deals with the design optimization and performance analysis of outer rotor PMFSM for the downhole application. Preliminary, the basic design parameters needed for machine design are calculated mathematically. Then the design refinement technique is implemented through deterministic method. Finally, initial and optimized performance of the machine is compared and as a result the output torque is increase from 16.39 Nm to 33.57 Nm while diminishing the cogging torque and PM weight up to 1.77 Nm and 0.79 kg, respectively. Therefore, it is concluded that purposed optimized design is suitable for the downhole application.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.6
• /
• pp.60-64
• /
• 2002

This paper describes the machining characteristics of the MoSi$_2$--based composites through the process of electric discharge drilling with various tubular electrodes. In addition to hardness characteristics, microstructures of Nb/MoSi$_2$laminate composites were evaluated from the variation of fabricating conditions, such as preparation temperature, applied pressure, and pressure holding time. MoSi$_2$-based composites have been developed in new materials for jet engines of supersonic-speed airplanes and gas turbines for high-temperature generators. These high performance engines may require new hard materials with high strength and high temperature-resistance. Also, with the exception of grinding, traditional machining methods are not applicable to these new materials. Electric discharge machining (EDM) is a thermal process that utilizes a spark discharge to melt a conductive material. The tool electrode is almost -unloaded, because there is n direct contact between the tool electrode and the work piece. By combining a non-conducting ceramic with more conducting ceramic, it was possible to raise the electrical conductivity. From experimental results, it was found that the lamination from Nb sheet and MoSi$_2$ powder was an excellent strategy to improve hardness characteristics of monolithic MoSi$_2$. However, interfacial reaction products, like (Nb, Mo)SiO$_2$and Nb$_2$Si$_3$formed at the interface of Nb/MoSi$_2$, and increased with fabricating temperature. MoSi$_2$composites, with which a hole drilling was not possible through the conventional machining process, enhanced the capacity of ED-drilling by adding MbSi$_2$, relative to that of SiC or ZrO$_2$reinforcements.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.03a
• /
• pp.18-23
• /
• 1996

The Job of Milling in the Local Skill Contest in 1996 was to assemble parts into a complete whole of the parts number 1, 3, 4 worded by Milling Machine and the parts number 2 worked by Machining Center. In the parts of Milling Machine, the Job was to work 45$^{\circ}$angle working, T-slot, dovetail, the correct position drilling, rimming, boring, etc. In the Machining Center, there were the way of calculation of point of contact of 'R' contour curved line and lots of working elements. So, it was possible to work the parts and assemble them within the time limit only through the program to be made out in the way to shorten working hours.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.6
• /
• pp.271-279
• /
• 2020

Non-ferrous metals, widely used in the mechanical industry, are difficult to machine, particularly by drilling and tapping. Since non-ferrous metals have a strong tendency to adhere to the cutting tool, the tool life is greatly deteriorated. Diamond-like carbon (DLC) is one of the promising candidates to improve the performance and life of cutting tool due to their low frictional property. In this study, a sacrificial DLC layer is applied on the hard nitride coated drill tool to improve the durability. The DLC coatings are fabricated by controlling the acceleration voltage of the linear ion source in the range of 0.6~1.8 kV. As a result, the optimized hardness(20 GPa) and wear resistance(1.4 x 10-8 ㎣/N·m) were obtained at the 1.4 kV. Then, the optimized DLC coating is applied as an sacrificial layer on the hard nitride coating to evaluate the performance and life of cutting tool. The Vickers hardness of the composite coatings were similar to those of the nitride coatings (AlCrN, AlTiSiN), but the friction coefficients were significantly reduced to 0.13 compared to 0.63 of nitride coatings. The drilling test were performed on S55C plate using a drilling machine at rotation speed of 2,500 rpm and penetration rate of 0.25 m/rev. The result showed that the wear width of the composite coated drills were 200 % lower than those of the AlCrN, AlTiSiN coated drills. In addition, the cutting forces of the composite coated drills were 13 and 15 % lower than that of AlCrN, AlTiSiN coated drills, respectively, as it reduced the aluminum clogging. Finally, the application of the DLC sacrificial layer prevents initial chipping through its low friction property and improves drilling quality with efficient chip removal.