• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1625-1630
• /
• 2004

An experimental study was carried out to investigate influence of flow conditions on a boundary layer to the near-wake of a flat plate. The flow condition in the vicinity of trailing edge that is influenced by upstream condition history is an essential factor that determines the physical characteristics of a near-wake. Various tripping wires were used to change boundary layer flow condition of upstream at the freestream velocity of 6.0 m/sec. Measurements of the boundary layer and near-wake according to the change of upstream conditions were conducted by using both I-probe(55P14 for boundary layer) and X-probe(55P61 for wake). Normalized velocity profiles of the boundary layer were shown the flow types such as laminar boundary layer, transition, and turbulent boundary layer at 0.95C from the leading edge. The velocity and turbulence intensity profiles of the near-wake for the case of laminar boundary layer at the flat plate surface exhibited a defect and a double peak showing perfect symmetry, respectively.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.558-562
• /
• 2000

This research is concerned with the experiments on buckling characteristics of strain energy hinge(SEH) for solar arrays. The dynamic characteristics of the strain energy hinge is very important since it affects the shape and speed of the solar array deployment. The rapid deployment results in overshoot and undesirable residual vibrations. In this study, we carry out a series of buckling experiments to identify the dynamic characteristics of the SEH, which is made of strip measures. Buckling tests were done on the single-plate, double-plate and triple-plate SEH and VSEH. The experimental results show that the SEH has a very complex buckling behavior which can not be coped with theoretically. The modeling problem of the SEH is also discussed.

• 콘크리트학회논문집
• /
• 제14권1호
• /
• pp.126-135
• /
• 2002

기존 철근콘크리트 구조물에 대한 보강 방법으로서 강판접착공법은 강판의 박리나 rip-off 등 조기 파괴의 문제점을 안고 있음에도 불구하고 가장 널리 이용되고 있다. 그러나, 아직까지도 이러한 조기 파괴 문제점은 강판 단부의 접착계면 주위의 국부적인 파괴메커니즘 관점에서 파악되지 않고 있다. 그러므로, 이 연구에서는 보강판의 파괴 메카니즘을 구명하고 접착계면에서의 박리기준을 제시하는 것을 목적으로 하고 있다. 이러한 목적으로 두 가지 방법에 의한 광범위한 실험이 수행되었는데, 그 하나가 순수 전단력이 작용하는 상태를 고려한 double lap pull-out test이고, 또 다른 하나는 휨과 전단이 동시에 작용하는 상태를 고려한 half beam test이다. 주요 실험변수로 강판의 두께, 접착제의 두께, 부착길이, 그리고 단부 처리방법 등을 채택하였으며, 이를 토대로 하여 각 변수에 의한 영향을 다각도에서 분석하였다. 강판의 길이방향으로의 변형률을 측정하여 그로부터 접착계면에서의 전단응력을 계산하였으며, 콘크리트와 강판의 상대 변위를 측정하여, 접착계면의 전단계수를 얻고자 하였다. 이러한 실험 결과를 이용하여 비선형 유한요소 해석결과와 비교를 통하여 실험의 검증 및 강판의 단부 접착계면에 발생하는 전단응력 및 법선응력을 도출하였다. 해석결과 최대 하중뿐만 아니라 균열패턴 등도 실험결과와 잘 부합되는 것으로 나타났다. 최종적으로, 해석으로부터 얻은 최대 전단응력과 법선응력의 관계를 이용하여 접착계면의 박리가 발생하는 기준치를 제시하였다. 이러한 연구 결과는 강판 보강된 콘크리트 휨부재에 대하여 보다 현 실적인 설계 및 해석을 가능케 할 것으로 사료된다.mitted) = 369.4$_{A}$V sub p/ - l237.8 ＜기중양생>lpha$), head separation factor($\beta$), tail separation factor((equation omitted))값이 증가하였다.C$였다.$였다.X>였다..X>였다.할 것으로 생각되었으며, 향후 더 많은 환자들을 대상으로 장기간에 걸친 임상적인 연구가 필요할 것으로 생각되었다.ang with P. japonica Powder had the least sweet taste. In the flavor and overall Preference, the Doenjang with P. japonica powder was the lowestEX>로 측정되었고, 계사내 지붕의 표면 온도는 최고 $29^{\circ}C$가 측정되었다. 계사 내 표면 온도 및 닭의 표면 온도는 계사내 공기온도의 영향을 많이 받는 것으로 나타났다.ill in a good agreement with those predicted by Rohsenow's formula, which was based on nucleate boiling. For the condenser, the wall temperatures were practically uniform, and the measured values of condensation heat transfer coefficient were 1.7 times higher than the predicted values obtained from Nusselt's film

• 한국태양에너지학회 논문집
• /
• 제27권3호
• /
• pp.155-160
• /
• 2007

This study shows the results on thermal performance test with domestic solar collector for low-temperature applications using KS, then reveals the efficiency difference between KS and EN standard. Using the test results, this study Presents the status of thermal performance with domestic solar collector including flat-plate, single evacuated, and double evacuated (with mirror or U-tube) solar collector.

• 한국공간구조학회논문집
• /
• 제20권2호
• /
• pp.87-94
• /
• 2020

The present study is aimed to calculate the optimal damping according to the seismic load on the structure with a non-seismic design to perform structure analysis considering the deformation of structural joint connection and panel zone; to develop design program equipped with structural stability of the steel frame structures reinforced with the panel zone and viscous dampers, using the results of the analysis, in order to systematically integrate the seismic reinforcement of the non-seismic structures and the analysis and design of steel frame structures. The study results are as follows: When considering the deformation of the panel zone, the deformation has been reduced up to thickness of the panel double plate below twice the flange thickness, which indicates the effect of the double plate thickness on the panel zone, but the deformation showed uniform convergence when the ration is more than twice. The SMRPF system that was applied to this study determines the damping force and displacement by considering the panel zone to the joint connection and calculating the shear each floor for the seismic load at the same time. The result indicates that the competence of the damper is predictable that can secure seismic performance for the structures with non-seismic design without changing the cross-section of the members.

• 한국태양에너지학회 논문집
• /
• 제21권4호
• /
• pp.63-71
• /
• 2001

This work has been carried out to find the ideal operating conditions for solar vacuum tube collectors which are widely used at present. Various types of solar collectors including a flat plate one were experimentally tested and examined to determine their thermal efficiencies and operating characteristics. Generally, solar vacuum tubes can be classified into two groups according to their design features. Of these, one is characterized by the insertion of a metallic device(such as a finned heat pipe) in an evacuated glass tube for the collection and transportation of solar energy. The other utilizes double glass tubes where the smaller one is contained inside the bigger one and soldered to each other after the small gap between them is evacuated. Both of these solar collectors are designed to minimize convection heat losses by removing the air which is in direct contact with the absorber surface. The performance of the former type can be readily analyzed by applying the relevant correlations developed for flat plate solar collectors. This has been demonstrated in the present study for the case of a solar collector where a heat pipe is inserted in an evacuated tube.

• 대한조선학회지
• /
• 제13권4호
• /
• pp.19-24
• /
• 1976

Some method of analysis of rectangular plates under distributed load of various intensity with all edges built in are presented in. Analysis of many structures such as bottom, side shell, and deck plate of ship hull, and flat slab, deck systems of bridges is a problem of plate with continuous supports or clamped edges. When the four edges of rectangular plate is simply supported, the double fourier series solution developed by Navier can represent an exact result of this problem. If two opposite edges are simply supported, Levy's method is available to give an "exact" solution. When the loading condition and boundary condition of a plate does not fall into these cases, no simple analytic method seems to be feasible. Analysis of a plate under distributed loads of various intensity with all edges built in is carried out by applying Navier solution and Levy's method as well as "Principle of Superposition" In discussing this problem we start with the solution of the problem for a simply supported rectangular plate and superpose on the deflection of such a plate the deflections of the plate by slopes distributed along the all edges. These slopes we adjust in such a manner as to satisfy the condition of no rotation at the boundary of the clamped plate. This method can be applied for the cases of plates under irregularly distributed loads of various intensity with two opposite edges simply supported and the other two edges clamped and all edges simply supported and this method can also be used to solve the influence values of deflection, moment and etc. at arbitrary position of plates under the live load.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.209-212
• /
• 2008

건설공사에서 지하공사의 DBS(Double Beam as Struts)공법은 지하 수평부재의 공장제작 및 모듈화 된 부재 생산을 통해 공기를 단축할 수 있으며, 수평재를 영구부재로 사용할 수 있는 장점이있다. 그러나 DBS공법의 구성요소로서 시공 및 사용 시 수평부재에 작용하는 수직하중을 기둥에 전달하기 위하여 개발된 정(${\sharp}$)자형 더블보-기둥 접합부는 복잡한 다축 응력상태의 전단에 의해 지배를 받는다. 이 연구에서는 정(${\sharp}$)자형 더블보-기둥 접합부의 전단파괴 기구와 구속철판 두께에 따른 전단내력 증가를 확인하기 위해 총 7 개의 실험체를 제작하여 1 방향 정적실험을 수행하였다. 실험결과, 실험체는 모두 취성파괴 되었고 실험의 지지조건에 따른 보작용과 아치작용에 의한 전단파괴 양상을 보였으며 철판의 구속이 슬래브의 전단내력을 1.06${\sim}$1.48 배 증가시키는 것으로 나타났다. 또한, 2 방향 구속철판이 동일하지 않은 경우가 구속철판이 동일한 경우보다 전단내력이 더욱 증가한 것으로 나타나 구속철판이 동일하지 않은 경우가 효율적이었다.

• Structural Engineering and Mechanics
• /
• 제50권4호
• /
• pp.525-539
• /
• 2014

Bonded composite-patch repair has been widely used to restore or extend the service life of damaged structures due to its effectiveness as a mechanical repair technique. In this paper using extended finite element method (XFEM), three-dimensional crack models are developed to examine the fracture behavior of centrally cracked aluminum plates repaired with single and double sided composite patches. Stress intensity factor (SIF) at the crack tip is used as the fracture criterion. In this regard, the effects of the crack lengths, patch materials, orientation of plies, adhesive and patch thickness are examined to estimate the SIF of the repaired plate and the repair performance. The obtained results show that composite patches have significant effect on reduction of the SIF at the crack tip. It is also proved that using double symmetric repair, in comparison to single one, reduces considerably SIF at the crack tip. Hence, the residual strength can be improved significantly as well as fatigue life of the structure. Investigation of ply orientation effects shows SIF increase as the ply orientation is changed from $0^{\circ}$ (perpendicular to the advancing crack) to $90^{\circ}$ (parallel to the crack line). However, the effectiveness of the ply orientation depends on the loading direction and the crack direction.

• 제어로봇시스템학회논문지
• /
• 제5권5호
• /
• pp.577-584
• /
• 1999

In this paper, the double inverted pendulum having a single actuator is built and the controller for the system is proposed. The lower link of the target pendulum system is hinged on the plate to free for rotation in the specified range($10^{\cire}$) on the x-z plane. The upper link is connected to the lower link through a DC motor. The double inverted pendulum built can be kept upright posture by controlling the position of the upper link even though it has no actuator in lower hinge. The algorithm to control the inverted pendulum consists of a state feedback controller within a linearizable range and a fuzzy logic controller coupled with a nonlinear feedback compensator for the rest of the range. Conventional state feedback control is employed, and the fuzzy controller is responsible for generating the reference joint angle of the upper link for the nonlinear feedback compensator which drives a DC motor to generate an indirect torque to the lower joint. As a result, we can get the upright posture of the proposed pendulum system. Simulations and experiments are conducted to show the validity of the proposed controller.