• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.82-84
• /
• 2002

Dimensionally stable anode(DSA) can be used for the electrowinning of non-ferrous metal like as a Zn, and electrolysis of sea water. $MnO_2$ electrode satisfies the requirements of DSA, and has a good cycle life and a low overpotential for oxygen evolution. $MnO_2$ electrodes coated with DMF and PVDF based on Pb alloy produced at several compositions and dry temperatures. The viscosity of solvent used as a binder of $MnO_2$ powder increased with the increasing PVDF contents. When the ratio of PVDF to BMF with the 5 times dipping at the solution mixed with PVDF and DMF was 1/9, the coating thickness was $150{\mu}m$. When the ratio of PVDF to $MnO_2$ was lower than 1/6, the electrode didn't show any reaction irrespective of the concentrations of DMF. However, When the ratio of PVDF to $MnO_2$ was higher than 1/6, the electrode showed a constant current reactions and homogeneous cyclic voltammetry even though at a high cycle. The reason for the high current and homogeneous cyclic voltammetry is the good catalytic reactions of $MnO_2$ powder in electrode. The reactions of Pb electrode coated with $MnO_2$ and PVDF based on the pure Pb electrode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.200-203
• /
• 2003

A study on the arc resistance and light reflectance of PTFE (polytetrafluoroethylene) nozzle for circuit breaker is presented. PTFE has been used widely as a material for circuit breaker nozzle. PTFE has excellent electrical resistivity, high melt viscosity, chemical inertness, heat resistance and low loss factor. PTFE melts at $327\;^{\circ}C$ but the viscosity is very high above the melting point. In the arcing environment in a circuit breaker, the fraction of the power is emitted out of the arc and reaches the nozzle wall by radiation, causing ablation at the surface and in the depth of the wall. Some fraction of the radiation power emitted out of the arc directly break up the chemical bonds at the surface while some fraction of the radiation power penetrates into the wall, heats up the material to evaporation temperature and causes damages deeper inside the volume of the nozzle. In this paper, some fillers that have endurance in the high temperature arc environment were added into PTFE. Adding some fillers into PTFE was expected to be efficient in improving the endurability against radiation. The light reflectance and arc resistance of PTFE composites were investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.204-207
• /
• 2003

This paper presents the electrical properties of PTFE (polytetrafluoroethylene) nozzle for circuit breaker. PTFE has been used widely as a nozzle material for circuit breaker. In the arcing environment in a circuit breaker, radiation is considered to be the major energy transport mechanism from the arc to the wall. The fraction of the radiation power is emitted out of the arc and reaches the nozzle wall, causing ablation at the surface and in the depth of the wall. The energy concentration in the material lead to the depolymerization and eventually lead to the generation of decomposed gas as well as some isolated carbon particles. The generation of the decomposed gas in the depth of the material causes inner explosion. The surface of nozzle becomes uneven. The flow of gas is not uniform due to the unevenness of the surface. Adding some fillers into PTFE is expected to be efficient for improving the endurability against radiation. In this experiment, three kinds of fillers that have endurance in the high temperature environment were added into PTFE. Dielectric constant, dissipation factor, electrical resistivity and dielectric strength of PTFE composites were investigated.

• Korean Journal of Applied Biomechanics
• /
• v.24 no.4
• /
• pp.399-415
• /
• 2014

The aim of this study was to investigate the effect of resistance training with and without whole-body vibration(WBV) on the biomechanical properties of the plantarflexor in the elderly women (>60 yrs., n=35). Thirty-five volunteers were randomly assigned to a resistance training with WBV group (RVT, n=14), a resistance training without WBV (RT, n=11), and a non-training control group (CON, n=10). The RVT and the RT groups participated in the training sessions three times a week for 8 weeks, followed by a 4-week detraining period. The CON group was instructed to refrain from any type of resistance training. To assess strength and activation of the plantarflexor muscles, maximum isometric ankle plantarflexion torque and muscle activation of the triceps surae muscles were measured using dynamometry, twitch interpolation technique and electromyography at four different ankle joint angles. Also, the lower extremity function was assessed by vertical jumping. The measurements were performed prior to, 2 and 8 weeks after the training and after a 4-week detraining period. Following the 8-week training sessions, an increase in the isometric plantarflexion strength was found to be greater for the RVT compared with the RT group (p<.05). Muscle inhibition was significantly decreased after training than before training only for the RVT (p<.05). Following the detraining period, a decrease in isometric plantarflexors strength and a increases in muscle inhibition were significantly less in the RVT compared with the RT group. In conclusion, the exercise with WBV is a feasible training modality for the elderly and seems to have a boosting effect when used with conventional resistance training.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.3
• /
• pp.61-68
• /
• 2007

When an active muscle is stretched, its steady-state isometric force following stretch is greater than that of a purely isometric contraction as the corresponding muscle length, referred to as force enhancement (FE). The purpose of this study was to investigate possible effects of muscle architecture on the FE. While subject performed maximal isometric dorsiflexion (REF) and isometric-stretch-isometric dorsiflexion (ECC) contractions, ankle joint angle and dorsiflexion torque using a dynamometer and electromyography of the tibialis anterior and the medical gastrocnemius muscles were measure. Simultaneously, real-time ultrasound images of the tibialis anterior were acquired. Regardless of the speed of stretch of the ECC contractions. the torques produced during the isometric phase following stretch ($37.3{\pm}1.5\;Nm$ ($10{\pm}3%$ FE) and $38.3{\pm}1.5$ ($12{\pm}3%$ FE) for the ECC contractions with $15^{\circ}$/s and $45^{\circ}$/s stretch speeds, respectively) were greater than those of the REF contractions ($34.5{\pm}2.5\;Nm$). Moreover, the amount of FE was found to be stretch speed dependent. Angles of pennation ($\alpha$) during the isometric phase following stretch were the same for the REF ($15{\pm}1^{\circ}$) and the ECC ($14{\pm}1^{\circ}$(LS), $15{\pm}1^{\circ}$(LF)). During the same phase, muscle thicknesses were the same ($14.9{\pm}0.6$, and $14.9{\pm}0.5\;mm$ for the REF and the ECC contractions, respectively). For a large limb muscle, the tibialis anterior muscle, a similar amount of force enhancement was observed as did for other human skeletal muscles. Architectural variables, pennation angle and thickness, were not systematically different between the REF and ECC contractions when FE occurred. Therefore, the results of this study suggest that muscle architecture may have little influence on the production of FE.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.85-90
• /
• 2012

Wet pressing process has great influence not only on the paper properties but also on the efficiency of total manufacturing process including energy efficiency. The slow drainage propensity of old corrugated container(OCC) might require more complicated control of wet pressing process. In this study, the change in press efficiency and in structure of wet sheet by the various condition of laboratory roll press simulator were evaluated to provide background information about wet pressing of OCC. The higher pressure and the slower machine speed resulted in higher efficiency of wet pressing but the change trends of dryness depending on the wet press pressure and machine speed were shown differently according to OCC treatment. The effects of water contents of felt on the wet press efficiency and sheet structure were also investigated. The higher contents of water in felt resulted in less removal of water generally and the crushed structure of wet sheet were appeared especially at higher pressure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.110-110
• /
• 2010

본 실험에서는 Silicon (001) 기판을 사용하여 silicon 기판상에 modified Stranski-Krastanow(S-K) 방식으로 InAs quantum dot (QD) 을 성장하고 그 위에 InSb layer를 형성하였다. 기판온도 $390^{\circ}$에서 In injection period를 4번 반복하여 제작된 InAs quantum dot layer를 buffer로 사용하였으며, QD layer의 밀도는 $1{\mu}m^2$ 당 600개, height가 $6.2\;{\pm}\;2.0\;nm$, width가 $36.1\;{\pm}\;9.2\;nm$ 정도이다. 성장된 $2.8{\mu}m$ 두께의 InSb film의 특성을 분석해 보면 AFM 상에서의 root mean square (rms) roughness는 5.142nm정도이며, electron mobility는 340 K 에서 $41,352cm^2/Vs$, 1.8 K에서는 $4,215cm^2/Vs$ 정도를 나타내었다. 본 실험에서는 다른 실험과는 달리 InAs QD 을 buffer layer로 사용하였으며, silicon기판도 아무런 처리가 되지 않은 (001)기판을 사용하였으므로 기존의 다른 연구 결과와는 차별성을 가진다. 또한 buffer로 사용된 InAs quantum dot layer의 종류를 한 가지로 고정하고 실험을 하였지만 추후 더욱 다양한 밀도와 크기의 quantum dot layer를 적용시키고, 기존의 다른 논문에서 적용된 방법들을 추가로 적용시켜 본다면 mobility값은 더욱 증가할 것으로 생각된다. 이러한 연구를 통해 값이 싸고 구하기 쉬운 silicon기판상에 silicon에 비하여 더 좋은 특성을 갖는 III-V족 화합물 반도체 소자를 구현 할 수 있을 것으로 생각된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.315.1-315.1
• /
• 2013

표면 조직화의 목적은 태양전지 표면에서의 입사되는 빛의 반사율을 감소 시키고, 웨이퍼 내에서 빛의 통과 길이를 길게 하며, 흡수되는 빛의 양을 증가시키는 것이다. 본 연구에는 습식, 건식 표면조직화 방법에 따른 표면 형상과 표면 반사도를 분석 하였으며, 셀을 제작하여 전기적 특성과 광학적 특성의 상관관계를 분석하였다. 표면 조직화 공정은 염기성 용액인 KOH를 이용한 식각 방법과 Ag를 이용한 metal-assisted 식각, 산증기를 이용한 식각, 플라즈마를 이용한 반응성 이온식각을 적용하여 제작하였다. 표면 반사율을 400~1000 nm 사이의 파장에서 측정하였으며 KOH를 이용하여 식각한 샘플이 9.11%의 표면 반사율을 가졌으며 KOH를 이용하여 식각한 표면에 추가로 metal-assisted 식각을 한 샘플이 2%로 가장 낮은 표면 반사율을 보였다. 표면 조직화 후 동일 조건으로 셀을 제작 하여 효율 측정 결과 Ag를 이용한 2단계 metal-assisted chemical 식각이 15.83%의 가장 낮은 광변환 효율을 보였으며 RIE를 이용한 2단계 반응성 이온 식각공정이 17.78%로 가장 높은 광변환 효율을 보였다. 이 결과는 반사도 결과와 일치 하지 않았다. 표면 조직화 모양에 따른 셀 효율의 변화는 도핑 프로파일과 표면 재결합 속도의 변화 때문이라 생각되며 더 명확한 분석을 위해 양자 효율을 측정하여 분석을 시도하였다. 측정 결과 단파장 대역에서 낮은 응답특성을 가지는 것을 확인 할 수 있었는데 그 이유는 낮은 반사도를 가지는 표면조직화 공정의 경우 나노사이즈의 구조를 갖기 때문에 균일한 도핑 프로파일을 얻지 못해 전자 정공의 분리가 제대로 이루어지지 못하였고 표면 재결합 속도증가의 원인으로 단락전류와 개방전압이 낮아져 효율이 떨어진 것으로 판단된다. 실험 결과 도핑 프로파일의 균일성은 셀 효율 개선을 위해 낮은 표면 반사율 만큼 중요하다는 점을 알게되었다. 낮은 반사율을 갖는 표면조직화 공정도 중요하지만 표면에 따른 균일한 도핑 프로파일을 갖는 공정을 개발한다면 단파장 응답도가 향상되어 단락전류밀도의 상승효과를 얻을 수 있을 것이라 판단된다.

• Journal of Wetlands Research
• /
• v.12 no.1
• /
• pp.15-22
• /
• 2010

We measured net primary productivity, annual accumulation of organic carbon and leaf decomposition of Salix community in the flood plain of the Han River and the Nakdong River. Net primary productivity, annual accumulation of organic carbon of the Salix community were 22.5ton/ha/yr(16.7ton/ha/yr-31.2ton/ha/yr) and 9.7ton C/ha/yr(7.5ton C/ha/yr-14.0ton C/ha/yr) respectively, which showed the highest values among the woody plant communities reported in the Korea. It means that planting Salix in the flood plain of the river is the best way to remove carbon dioxides. The faster leaf decomposition occurred around, under and the herb of Salix community in order. Leaf decomposition rate of Salix was higher than that of mesophytes, but lower than that of hydrophytes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.6_spc
• /
• pp.729-735
• /
• 2016

According to the survey for working environment of the cashiers in highway tollbooths, workers replied that noise was the most harmful substances next to air pollutant in the tollbooth. Researches on the noise levels exposed to cashiers in the highway tollbooth scarcely have been performed. Therefore, the aim of this study was to acquire baseline data to prevent health impairments of the cashiers by evaluating noise level exposed to them. Noise dosimeters were used for monitoring workers' noise exposure level in the tollbooths at 8 different highway tollgates. The noise levels of tollbooths did not exceed noise exposure limit of the ministry of labor, 90 dB(A). The average TWA inside of the tollbooths was 55.4 dB(A) and the average TWA outside of tollbooths was 58.3 dB(A). The average TWA outside of tollbooths was slightly higher than that of inside of tollbooths. However, the significance probability(p-value) was 0.255 which means statistically not significant. The noise levels inside and outside of tollbooth were statistically significant to both mean traffic volume per day and traffic volume of passenger car.