• Transactions of Materials Processing
• /
• v.4 no.1
• /
• pp.17-27
• /
• 1995

The tact switch is widely used in electric and electronic products. The dome type tact spring is produced by stamping. Stamping of the tact spring and operation of the tact switch have been simulated by the elasto-plastic finite element method. The operating characteristics of the switch may be given by the relation between the operating force and stroke. For a given material, this is affected by two main factors. One is the geometry of dome spring which is determined by the geometry of stamping dies and the stamping pressure, and another one is the dimension of switch. From the calculation, it was possible to obtain the stamping conditions and switch dimension for a predetermined force-stroki relation And, the hoop stresses and effective strains distributions due to the stamping and during the operation of the switch indicate a possibility of cracking in the center and rim of dome spring.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.295-302
• /
• 1999

This paper is the experimental and analytic of reinforced concrete hemisphere dome under vertical load. It is described that when the reinforced concrete hemispherical dome supported on cylindrical wall is loaded vertically, how the opening part of dome will behave mechanically The experimental and analytic model is a Hemispherical dome with opening and the meridian angle of opening is 76$^{\circ}$at the center of sphere under concentrated load around the opening, but this is reinforced by a ring is sufficient stiffness. The diagrams of crack development are represented to understand the behavior of the reinforced concrete hemispherical dome. The method of crack analysis will be applied the rigid element spring model. The rigid element spring model is a new discrete element analysis, each divided element is assumed by rigid elements without deformation which is interconnected with elasto-plastic spring system.

• Design & Manufacturing
• /
• v.14 no.1
• /
• pp.15-21
• /
• 2020

Smart systems in different application areas such as automotive, medical and consumer electronics require a novel manufacturing method of electronic, optical and mechanical functions into products. Traditional methods including mechanical assembly, bonding of plastic and electronic circuit cause the problems in large size of products and complicated manufacturing processes. In this study, thermoforming and film insert molding were applied to fabricate a dome shaped plastic part embedded with electronic circuits. The deformation of patterns printed on PET film was predicted by thermoforming simulation using T-SIM, and the results were compared with those by experiment. In order to decrease spring-back after thermoforming, the Taguchi method of design of experiment was used. Through ANOVA analysis, it was found that mold temperature was the most dominant parameter for spring-back. By using flow analysis, gate design was performed to decrease injection pressure. During film insert molding, the wash-out of ink printed on film occurred for Polycarbonate. When the resin was changed to PMMA, the wash-out disappeared due to low melt temperature.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.10a
• /
• pp.337-344
• /
• 2001

This paper is concerned with the change of joint rigidity in estimating the degree of semi-rigidity of connections and the buckling load in a single layer latticed dome. The estimations are based on information about the ratio for the rotational stiffness of the connection to the flexural stiffness of the member and the minimum eigenvalue of a structure for pinned, semi-rigid and completely rigid cases, respectively. Connection characteristics are reflected in the ratio control of joint rigidity for the DOFs to be related using the spring element by FEM.

• International journal of steel structures
• /
• v.18 no.5
• /
• pp.1699-1709
• /
• 2018

Suspen-dome structures are extensively used due to their superiority over traditional structures. The friction between cable and joints may severely influence the distribution of cable force, especially during the pre-stressing construction period. An accurate and efficient numerical method has not yet been developed that can be used for estimating the influence of friction on cable force distribution. Thus, this study proposes an efficient friction element to simulate friction between cable and joint. A flowchart for estimating the value of friction force is introduced. These novel numerical methods were adopted to estimate the influence of friction on cable force distribution. The accuracy and efficiency of these numerical methods were validated through numerical tests.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.9 no.4
• /
• pp.268-276
• /
• 2007

Urban atmosphere may play as a harbinger for the future climate change with respect to temperature and $CO_2$ concentration. The Seoul metropolitan area is unique in rapid urbanization and industrialization during the last several decades, providing a natural $CO_2$ dome with increased temperature. This study was carried out to evaluate the feasibility of using the urban-rural environmental gradient in replacement of the IPCC mid-term scenario (after 30-50 years). For this, we measured atmospheric $CO_2$ concentration and air temperature at three sites with different degree of urbanization (Seoul, Suwon, and Icheon). Results from 11-month measurement can be summarized as follows: (1) The annual mean $CO_2$ concentration across 3 sites was in the order of Seoul (439 ppm) > Suwon (419 ppm) > Icheon (416 ppm), showing a substantial urban-rural environmental gradient. (2) The diurnal fluctuation in $CO_2$ concentration was greater in summer than in winter, showing the effect of photosynthesis on local $CO_2$ concentration. (3) The daily maximum $CO_2$ concentration was observed at 0500 LST in spring and summer, 0800 LST in autumn, and 0900 LST in winter, showing the sunrise-time dependence. (4) The observed hourly maximum $CO_2$ concentration averaged for the whole period was 446 ppm in Seoul at 0700 LST, while the minimum was 407 ppm in Suwon at 1500 LST. (5) Compared with the background atmospheric concentration of $CO_2$ in Anmyeon-do (377.4 ppm annual mean), $CO_2$ concentration of the study sites was higher by 14% in Seoul, by 10% in Suwon, and by 9% in Icheon. The observed $CO_2$ concentration in Seoul reached already 98% of the 2030-2040 projection (450 ppm) and 80% of the 2040-2050 projection (550 ppm) under the IPCC BAU scenario, showing a feasibility of using the $CO_2$ dome of Seoul as a natural experimental setting for the mid-term climate change impact assessment.

• The Journal of the Petrological Society of Korea
• /
• v.19 no.2
• /
• pp.109-121
• /
• 2010

Mt. Mudeung is located in Gwangju city, Damyang-Gun, Hwasun-Gun and its round form give us the mood of soft and rich. Its location is $126^{\circ}06'-127^{\circ}01'E$ and $35^{\circ}06'-35^{\circ}10'N$ and its highest peak is Cheonwang-bong with the height of 1,187 m. The Gwangju city is located in the West of Mt. Mudeng and the mountain range with a small basin in its East. The pavilion such as the Soswaewon, Songganjeong, Sigyongjeong are distributed along the stream in the north of Mt. Mudeung. The mountain is formed from the volcanic activity, Gwangju cauldron during the Cretaceous. The top part of Mt. Mudeung is composed of dark gray quartz-andesite and its K-Ar whole rock age is $48.1{\pm}1.7Ma$. The composition of the north area, where the Wonhyosa temple is located, is micrographic granite, whereas the composition of south area is rhyolite mainly. The main ridge of Mt. Mudeung runs from North, starting from the Bukbong, to south, passing Cheonwangbong, Jangbuljae and ending Anyangsan. Geologic feature of the mountain includes volcanic landform, mountaineous landform, and stream landform. The Seosukdae, Ipseokdae, Gyubongam, which are main ridges and formed from volcanic activity, are composed of mainly columnar joint. Saeinbong and Majipbong in the south-west are composed of mainly cliff and dome. The typical erosion landform of the mountain has three different types of the weathering-cave, each of which reflect the property of the original rock. Four different area of wide block stream, they makes the geological feature of spring-water, though its scale is small compared to that of water fall.