• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.540-549
• /
• 2018

This paper proposes the method of active distribution network expansion planning considering distributed generation integration and distribution network reconfiguration. The distribution network reconfiguration is taken as the expansion planning alternative with zero investment cost of the branches. During the process of the reconfiguration in expansion planning, all the branches are taken as the alternative branches. The objective is to minimize the total costs of the distribution network in the planning period. The expansion alternatives such as active management, new lines, new substations, substation expansion and Distributed Generation (DG) installation are considered. Distribution network reconfiguration is a complex mixed-integer nonlinear programming problem, with integration of DGs and active managements, the active distribution network expansion planning considering distribution network reconfiguration becomes much more complex. This paper converts the dual-level expansion model to Second-Order Cone Programming (SOCP) model, which can be solved with commercial solver GUROBI. The proposed model and method are tested on the modified IEEE 33-bus system and Portugal 54-bus system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.5
• /
• pp.369-375
• /
• 2020

Distribution energy resources have been increasing in recent years. However, output power is limited for distribution network stability. This study proposes an active distribution network that can reconfigure distribution lines by using an active phase controller. A conventional distribution network has a fixed structure, whereas an active distribution network has a variable structure. Therefore, the latter can increase the output power of distribution energy resources and decrease the overload of distribution line facilities. An active phase controller has two operation modes for minimizing circulating current during dynamic reconfiguration. In this study, voltage and current control algorithms are proposed for active phase controllers. The simulation of the proposed methods for active phase controllers is performed using PSIM software.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.4
• /
• pp.405-420
• /
• 2003

Purpose : The purpose of this study was to compare the fracture resistance of the IPS Empress ceramic crown with 1.0mm width rounded shoulder, which is usually recommended in all ceramic crown. and 0.5mm width chamfer finish lines on the maxillary central incisor. Material and method : After 15 metal dies were made for each group, the IPS Empress all ceramic crowns were fabricated and cemented with resin cement(Bistite resin cement, Tokuyama Soda Co. LTD., Japan) on the metal die. The cemented crowns were mounted on the positioning jig and the universal testing machine(Zwick Z020, Zwick Co. Germany)was used to measure the fracture strength with loading on the incisal edge. And also, three-dimensional finite element stress analysis was used to measure the stress distribution with the various types of the finish lines(1.0mm width rounded shoulder, 0.5mm width chamfer), the loading site(incisal edge, incisal $\frac{1}{3}$) and the type of loading(concentration loading, distribution loading). Results and conclusion : 1. In the fracture resistance experiment according to the finish line, the mean fracture strength of rounded shoulder(876N) and the mean fracture strength of chamfer(882N) did not skew any significant difference between each other(p>0.05). 2. The stress distribution of all ceramic crown in three dimensional finite element analysis showed concentration aspect at loading point and cervical area or labial surface. 3. In metal die, there were no differences in stress distribution between finish lines, but in natural teeth model, chamfer finish line showed higher stress than rounded shoulder finish line. 4. When force was loaded on the incisal edge the stress was concentrated on the incisal edge and the cervical area of labial surface. When force was loaded on the incisal $\frac{1}{3}$, the stress concentrated on the cervical area of labial surface and the cingulum area. 5. Generally, natural teeth model showed higher and various stress than the metal die.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.52 no.4
• /
• pp.325-338
• /
• 2016

Properties of aggregation and spatial distribution of fish were examined based on three lines in the South Sea of Korea using three frequencies (18, 38, and 120 kHz) of a scientific echosounder. The vertical distribution of fish was displayed using acoustic biomass namely nautical area scattering coefficient (NASC). As a result, at 120 kHz high NASC showed from water surface to 20 meters in deep while at 18 and 38 kHz very high NASC presented in 70 ~ 90 meters in depth, especially at line 3. Among three lines, the line 2 had lowest NASC. The horizontal distribution of fish using three frequencies together exhibited high NASC between the eastern South Sea and center of South Sea. In especial, NASC ($801{\sim}1,920m^2/n{\cdot}mile^2$) was observed along coastal waters from Busan to Tongyeong, Geoje, and Namhae. In regard with the property of aggregation of fish schools, the volume back-scattering strength ($S_V$) of three lines presented close each other, however, the range of $S_V$ in the line 2 was shortest (-53.5 ~ -43.4 dB). The average distributional depth was deep in the order of L3 ($32.8{\pm}9.0m$), L1 ($45.2{\pm}9.5m$), L2 ($49.7{\pm}5.6m$). The average altitude was high in the order of L3 ($13.4{\pm}10.3m$), L1 ($17.0{\pm}12.6m$), L2 ($56.7{\pm}5.6m$). The average length, thickness, and area were large in the order of L1, L3, and L2. This means that small sized fish schools were distributed near water surface in the line 2 while relatively large and similar sized fish aggregations between line 1 and line 3 appeared however, fish schools at line 3 had lower distributional depth and smaller compared to those at line 1. Acoustic data were visualized for demonstrating the entire circumstances of survey area. Additionally, there was no correlation between acoustic and trawl results.

• Journal of Navigation and Port Research
• /
• v.42 no.6
• /
• pp.446-452
• /
• 2018

A traffic route is an area associated with high risk for accidents due to the flow of heavy traffic. Despite this concern, most studies related to traffic focus solely on traffic distribution. Therefore, there is a need for studies investigating the characteristics of ships' routes and traffic patterns. In this study, an investigation was carried out to analyze the traffic distribution and pattern in 3 major traffic routes for 3 days. For the purpose of the study, based on the prevailing traffic conditions, the route was divided into 10 gate lines. The ships passing through the lines were also classified into either small, medium and large. ND-K-S (normal distribution, kurtosis, and skewness) test was carried out for the traffic distribution at each gate line based on the information analyzed on each traffic route. The analysis of the results obtained from the ND test showed that large vessels have normal distribution, medium sized vessels have satisfied normal distribution in one-way route only while small sized vessels do not have normal distribution. According to the result obtained from the K-S test, normal traffic pattern shows a significant difference between two-way route and one-way route. Results obtained from the K test result shows that in the case of one-way route, vessels have a traffic pattern using a wide range on traffic route. Further analysis shows that vessels concentrate on one side of route in case of two-way route. Results obtained from the S test show that, in case of one-way route, vessels have a normal traffic pattern according to center line. However, analysis pf the results shows that vessels are shifted to the right side of route in case of two-way route. Despite these findings, it should be noted that this study was carried out in only 3 ports, therefore there is need for investigation to be carried out in various routes and conditions in future studies.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.6
• /
• pp.290-295
• /
• 2002

The present assignment in installing the number of switches for distribution line was made on the basis of a normal feeder capacity 7,000kVA in KEPCO(Korea Electric Power Corporation), Korea. But the normal capacity is revised to 10000kVA in 1998. Even increasing limit of the operating capacity of the distribution lines enables us to give some benefit for the operation flexibility and investment cost of the distribution system. It is disadvantageous in the viewpoint of supply reliability. In distribution systems, switches are equipped to improve the reliability of distribution systems by minimizing the outage section due to fault and maintenance. Utility generally improves the reliability by minimizing the length of outage section, which is caused by fault and maintenance, through switch equipment on distribution system. In order to cope with the changes such as operation capacity, it is necessary to study whether the present criteria is reasonable or not, also to confirm whether the present criteria of installing switches in line is improved or not. In this study, we proposes the number of switch per feeder on the basis of present operation capacity in distribution system.

• Journal of KSNVE
• /
• v.7 no.5
• /
• pp.747-756
• /
• 1997

Wigner-Ville distribution which is a time-frequency analysis has a fatal drawback, when the signal has multiple components. This is the cross-talk and often causes a neagative value in the distribution. Wingner-Ville distriution is an expression of power, therefore the cross-talk must be avoided. Smoothing the Wigner-Ville distribution by convoluting it with a window, is most commonly used to reduce the cross-talk. There can be infinite number of distributions depending on the windows. But, the smoothing reduces resolution in time-frequency plane; this motives to design a more effective window in reducing cross-talk while remaining resolution. The domain in which the cross-talk and legitimate components can be easily distinguished, is the ambiguity function. In the ambiguity function domain, the legitimate components appear as linear lines passing through the orgine. But, the cross-talk is widely distributes in the ambiguity function plane. Based on the relative distributions of cross-talk and legitimate components, rotating window can be designed to minimize cross-talk. Applying the rotating window to the ambiguity function corresponds to smoothing the Wigner-Ville distribution. Therefore, the effects of rotating window is estimated in terms of the bias error due to smooting the Wigner-Ville distribution. By applying the rotating window, not only the Wigner-Ville distribution but also its properties are changed. The properties of the new distribution are checked, in order to complete analyzing the rotating window.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.7 no.2
• /
• pp.69-77
• /
• 2004

Now, there are some problems to manage underground facilities in domestic. Specially, in the case of KEPCO(Korea Electric Power Corporation), it is so difficult to manage electronic line more stably and detailedly because the geographic information and attribute information being built is not easy to be updated in the field. KEPCO officials who are accompanying management and supervision in earthwork do not have sufficient knowledge and information about GIS but they grasp the information of geography and property which coincide with the field. Therefore they have to refer their business analysis contents sufficiently for more efficient lines management in the KEPCO, but it is problem that the existing information of electronic lines management system is not. In this study, we constructed power transmission and power distribution underground facility management system for the user to manage and maintain underground facilities more easily and safely using the information of geography and property about power transmission and power distribution underground facility which have been built by KEPCO.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.40-45
• /
• 2010

In order to establish the electric distribution system economically and operate efficiently, it becomes important to calculate energy losses of the system more accurately. This importance is not only related for the engineering of utilities' power network but also for the consumers' electric system. The Distribution Loss Factor (DLF) is the fundamental element of calculating the energy losses occurred through the electric system including the electric lines and equipments. Up to now, the DLF is calculated by empirical formulas using the correlation between the DLF itself and Load Factor. However, these methods have some limitations to reflect the various characteristics of the system and the load. In this regard, the novel method proposed here is developed to yield more accurate result of DLF which actively interacting with the characteristics and load patterns of the system. The improvement of accuracy is very significant according to the results of verification presented at the end of this paper.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.3
• /
• pp.472-480
• /
• 2007

This paper analyzes overvoltage on testing line for various parameter effect examination. Model systems consist of overhead line and underground cable. The model considered actual characteristic data of distribution lines. and will be constructed at testing yard. The simulations were performed under various line configuration such as cable kinds, cable length, lightning wave, lightning wave time, transformer and branch circuits. The simulation models are established by EMTP/ATPDraw and Line Constants are calculated by ATP_LCC. When lightning surge strikes on conductor of overhead line, EMTP/ATPDraw calculates overvoltage in many cases. Simulation results will be compared with real testing results at testing yard. The compared results will be used to establish protection methods in actual underground distribution systems.