• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• 제41권4호
• /
• pp.291-298
• /
• 2013

In this paper a new hybrid-type control system is proposed which reduces the pump speed of an electro-hydraulic actuator consisting of a pressure-compensated variable displacement piston pump and a valve-controlled hydraulic cylinder, whenever the flow rate demand is low. In order to avoid interfering with the pressure regulator which also has an effect on swash plate angle, the pump speed is changed in proportion to the mean value of the speed component of position commands. Additionally a pressure switch is employed to prevent the system pressure from getting lower than a reference value. Based on computer simulation & experimental results, it is shown that the hybrid control can save the idling power up to 44% at a stand-by mode by reducing the pump speed from 1,800 rpm to 600 rpm without affecting the dynamic response of the electro-hydraulic actuator.

• Korean Journal of Applied Biomechanics
• /
• 제16권1호
• /
• pp.109-117
• /
• 2006

The purpose of this study was done in order to investigate the Kinematical variables of the Rybalko motion on the Horizontal bar using the 3-dimensional cinematographic method. For this study, three excellent athletes take part in a 2003 Daegue universid game were chosen. The subject,s Rybalko motion was filmed with S-VHS camera at the speed of 60 fields per second and digitized the each fields. And the Kwon3D 3.1 version program was employed to obtain 3-dimensional data. As a result of this study. 1. A total time spent for performing Rybalko skill was Mean $2.52{\pm}0.13sec$. From starting down swing to releasing right hand the Mean $0.84{\pm}0.24sec$ was taken. 2. In the event 3 of Rybalko motion, that is, the moment which the right-hand is released on the bar, the center of mass must is employed at the position above the horizontal line of bar. In this research, the average vertical displacement(z axe) of center of mass shows $47.87{\pm}3.14cm$. 3. In the event 5, that is, the moment which the right-hand is catched again on the bar, the center of mass is employed at the position before the vertical line of bar. In this research, the average horizontal displacement(z axe) of center of mass shows $47.87{\pm}3.14cm$. 4. It has been seen that, at the moment of release of right-hand, lateral variation of center of mass is 13.395cm, vertical variation of center of mass is 7.41cm Thus, it is concluded that lateral variation of center of mass should be reduced for high grade to be acquired. 5. It has been founded that high speed of down swing influences speed of up swing, and that, in the motion of twist, the horizontal speed is little changed.

• International Journal of Highway Engineering
• /
• 제14권6호
• /
• pp.159-165
• /
• 2012

PURPOSES : The lack of details of guidelines on how to install the Chicane for traffic calming leads the practical difference across the calming areas, so the benefits expected from these facilities are not hardly observed. In this context, this study analysed the relationship between the geometric design alternatives of Chicane with the dynamic behaviour of vehicles in terms of speed and trajectory. METHODS : The study analysed vehicle dynamic behaviour using dynamic analysis program Auto-Turn under various geometric conditions of Chicane. RESULTS : This study suggested the design alternatives of Chicane using terms such as "longitudinal displacement value", "lateral displacement value", etc. which are defined in the study. The suggested combination set is fulfilling the desired or target speed of vehicles and clearance between vehicle and roadside at the same time. CONCLUSIONS : The results from this study can be applied to install Chicane corresponding to the local condition where target speed is 30km/h. The study showed the design alternatives of chicane corresponding to the given road cross-sectional design and clearance to roadside for passenger cars and light truck respectively.

• Proceedings of the KSR Conference
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.71-79
• /
• 2008

The concrete track is being used at the Phase II of the Kyeongbu High Speed Railway and New Constructed Honam High Speed Railway. When it makes a decision of bridge type, It has to consider about longitudinal forces of Continuous Welded Rail, Displacement at the end of bridges, Up-lift forces for fastener on the track. If it is installed turnout on the bridge, There is likelihood of the deck twist by applying the each difference longitudinal forces at the 4 each rails and the buckling by concentration of rail stress at the turnout. Moreover, If it is installed turnout on the continuous bridge and REJ(Rail Expansion Joint) on the main track or turnout track. It is hard to keep a safety for rail because of coming to twist or folding at the expansion of deck on the turnout track. Therefore when it is a design of bridge with turnout. It need to take bridge type to minimize an additional axial force and a displacement at the turnout. This paper makes a study of the composite steel arch bridge that is able to resolve criteria requirements of safety for track with turnout and suggest a helpful design method for bridge considering track with turnout by being based on design and construction method of Eonyang Bridge at the north part of Ulsan Station in Phase II of the Kyeongbu High Speed Railway.

• Transactions of Materials Processing
• /
• 제27권6호
• /
• pp.331-338
• /
• 2018

Electrohydraulic forming (EHF) process is a high speed forming process that utilizes the electric energy discharge in fluid-filled chamber to deform a sheet material. This process is completed in a very short time of less than 1ms. Therefore, finite element analysis is essential to observe the deformation mechanism of the material in detail. In addition, to perform the numerical simulation of EHF, the material properties obtained from the high-speed status, not quasi static conditions, should be applied. In this study, to obtain the parameters in the constitutive equation of Al 6061-T6 at high strain rate condition, a surrogate model using an artificial neural network (ANN) technique was employed. Using the results of the numerical simulation with free-bulging die in LS-DYNA, the surrogate model was constructed by ANN technique. By comparing the z-displacement with respect to the x-axis position in the experiment with the z-displacement in the ANN model, the parameters for the smallest error are obtained. Finally, the acquired parameters were validated by comparing the results of the finite element analysis, the ANN model and the experiment.

• Smart Structures and Systems
• /
• 제18권5호
• /
• pp.865-884
• /
• 2016

We have previously demonstrated a microfluidic elastomer, which changes apparent color and could have potential applications in smart windows. The practical use of such functional microfluidic systems requires rapid and uniform fluid displacement throughout the channel network with minimal amount of liquid supply. The goal of this simulation study is to design various microfluidic networks for similar applications including, but not limited to, the color-switching windows and compare the liquid displacement speed and efficiency of the designs. We numerically simulate and analyze the liquid displacement in the microfluidic networks with serpentine, parallel and lattice channel configurations, as well as their modified versions with wide or tapered distributor and collector channels. The data are analyzed on the basis of numerical criteria defined to evaluate the performance of the corresponding functional systems. We found that the lattice channel network geometry with the tapered distributors and collectors provides most rapid and uniform fluid displacement with minimum liquid waste. The simulation results could give an important guideline for efficient liquid supply/displacement in emerging functional systems with embedded microfluidic networks.

• Journal of the Korean GEO-environmental Society
• /
• 제22권7호
• /
• pp.13-20
• /
• 2021

The problem of subsidence of the roadbed near the Honam High Speed Railway, which opened in April 2015, continues to be raised, and the ground stability of the area near the Honam High Speed Railway may also be problematic. It is very important to select the factors that determine the indicators and indicators in producing the risk maps. Existing risk indicators are calculated as the final displacement volume based on the last observed date of the observed period, and time-series indicator displacement must be identified to analyze the cause of subsidence and the behavior of the indicator. Furthermore, for a wide range of regions, it is economically inefficient to conduct direct level measurements, so we wanted to observe surface displacement using SAR images. In this paper, time series indicator displacement was observed using PS-InSAR techniques, and risk was compared by rating each factor using the difference between final indicator displacement, cumulative indicator displacement, minimum displacement and maximum displacement as factors for determining risk indicators. As a result, the risk rating of the final displacement is different from that of each factor, and we propose adding factors from different perspectives in determining risk indicators. It is expected to be an important study in finding the cause of ground subsidence and finding solutions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제35권9호
• /
• pp.1051-1061
• /
• 2011

The influences of density variation on stress and displacement fields at a propagating Mode-III crack tip in orthotropic functionally graded materials (OFGMs) are studied. The crack propagates dynamically at a right angle to the gradient of physical properties. Three kinds of elasticity and density gradients are analyzed in this study. They are as follows: (1) the density varies without elasticity variation, (2) the directions of the density and elasticity gradients are opposite to each other, and (3) same. For these cases, the stress and displacement fields at the crack tip are developed and the dynamic stress intensity factors for propagating cracks are also studied. When the crack speed is low, the influence of density variation on the stresses and displacement is low. However, when the crack speed is high, this influence is very high.

• Journal of the Korean Geosynthetics Society
• /
• 제20권1호
• /
• pp.1-8
• /
• 2021

In urban areas, structures are installed deep underground in the lower part of the structure to utilize space. Therefore, a retaining wall is used to prevent earth pressure from the ground when constructing a structure. Due to the development of construction technology, retaining wall applied to excavation work are used to prevent danger such as falling rocks and landslides in temporary facilities when construction or retaining walls are installed. In general, the application of a retaining wall to a temporary facility during the embankment construction is the case of expanding an existing roads or railways. Therefore, it is necessary to study the retaining wall applied to the embankment construction such as the double-track site of the high-speed railway. In this study, two types of common one row H-pile retaining wall and two types of IER retaining wall were analyzed, and the stability of the retaining wall applied to the construction of double-track of the high-speed railway was analyzed. The earth retaining wall is a construction method that combines forced pile applied to the stabilization of the slope with the wall of the earth retaining wall. As a result of the analysis, the IER retaining wall had maximum lateral displacement of 19.0% compared to the type with H-plie installed only in the front while dynamic load was applied. In addition, the slower the speed of high-speed railway, the more displacement occurred, and the results show that more caution is needed when designing the ground in low-speed sections.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.47-50
• /
• 2000

Optical triangulation is one of the most common methods for acquiring range data. Using this method. We have developed a new type of Laser Displacement Sensor. We used Area CCD instead of linear CCD and PSD (Position Sensitive Detector). And we have developed the robust algorithm for increasing the accuracy and used USB instead of RS-232C for increasing speed. We present results that demonstrate the validity of our method using optical triangulation technique, Area CCD, and USB.