• 한국운동역학회지
• /
• 제27권3호
• /
• pp.171-179
• /
• 2017

Objective: The purpose of this study was to perform a kinematic and kinetic analysis of double-under jump rope technique according to skill level and sex. Method: Participants comprised a skilled group of 16 (9 males, 7 females), and an unskilled group of 16 with 6 months or less of experience (9 males, 7 females). Five consecutive double-under successes were regarded as 1 trial, and all participants were asked to complete 3 successful trials. The data for these 3 trials were averaged and analyzed after collecting the stable third jump in each trial. The variables used in the analysis included phase duration, total duration, flight time, vertical toe height, stance width, vertical center of mass displacement, and right lower limb ankle, knee, and hip joint angles in the sagittal plane during all events. Results: The skilled group had a shorter phase and total duration and a shorter flight time than the unskilled group. The vertical center of mass displacement and ankle dorsiflexion angle were significantly smaller in the skilled group. The male group had a shorter phase duration than the female group. The vertical toe height was greater, the stance width was smaller, and the ankle and hip flexion angles were smaller in the male group. Conclusion: Variables that can be used to distinguish between skill levels are phase and total duration, flight time, vertical center of mass displacement, and ankle dorsiflexion angle. Differences between sexes in double-under jump rope technique may be related to lower limb flexion angle control.

• 한국운동역학회지
• /
• 제13권3호
• /
• pp.99-116
• /
• 2003

The purpose of this study was to kinematics factors on during round-off at end of beam-salto backward stretched with step-out to cross on balance beam. Four elite female gymnastics players participated as subject of this study. The methods of this study was analyzed using three dimentional analysis. The results and conclusion of this paper is obtained as follows ; 1. The phase of time was the most short time in board touch down phase and board take-off phase. Also, it was shown a more long time in total time compared to previous study. 2. The horizontal displacement of each phase was shown the most high levels in balance beam landing. The vertical displacement was display a non-linearity increase in board take-of phase, and it was shown the most high levels in vertical displacement during landing of balance beam. 3. The horizontal velocity of each phase was shown the most high levels in board touch down, and it was display a gradually decreased levels because flight during board take-of. The resultant velocity of CG on each phase was shown the most high levels in board touch down and board take-off. 4. The angle of hip joint was shown the most high levels as performed a motion in extension state during board take-off, and the angle of knee joint was display a increased levels because of flight cause body extension in board take-off. Also the angle of ankle joint was shown a increasing levels during board take-off. Considering to this results, it is suggest that the change of kinematics factors in board touch down and board take-off is key role on the effective board control.

• 구강회복응용과학지
• /
• 제19권3호
• /
• pp.139-151
• /
• 2003

This study was to evaluate and to compare the compressive strength and the displacement effecting the abutment or the residual ridge which are transformed by the angle and the heights of the konus denture inner crown when restorating the unilateral konus denture by using the mandibular canine and the 1st premolar as an abutment. The author made 9 different models for different inner crown heights and konus angles. The inner crown height were divided to 5mm, 6mm, and 7mm and konus angles was divided to $4^{\circ}$, $6^{\circ}$, and $8^{\circ}$. And then in each model, 5kg of $15^{\circ}$ mesial load was stressed on the central fossa of the 1st premolar and the 1st molar. The stresses and displacement were measured using the finite element analysis. The results were as follows 1. The maximum compressive strength was shown on the connective area of the abutment and the denture base. 2. As the angle of the inner crown becomes increased, the compressive strength was shown smaller. 3. As the height of the inner crown becomes increased, the maximum compressive strength was shown smaller while the compressive strength of the root apex and the residual ridge showed larger. 4. When the stress was loaded only on the 1st premolar, the more compressive strength was concentrated on the root apex area of the 1st premolar. 5. When the stress was loaded only on the 1st premolar, the compressive strength was concentrated uniformly on the abutment and the residual ridge. 6. When the stress was loaded only on the 1st molar, the maximum displacement was shown on the distal part of the residual ridge.

• PNF and Movement
• /
• 제13권1호
• /
• pp.39-46
• /
• 2015

Purpose: The accelerometer is a tool for evaluating walking by the displacement of the center of mass (COM) in the body. Recently, smartphones have added an accelerometer app, and it can be used to evaluate outcomemanures in rehabilitation. The purpose of this study was to investigate the COM in the bodies of normal persons and stroke patients using this smartphone application while walking. Methods: Twenty normal persons and twenty-two stroke patients were recruited and had their COM measured using G-walk and the smartphone application, SMAP, during 10 m walking. Subjects repeated the 10 m of walking 3 times, and we used the SMAP, Accelerometer Monitor ver. 1.5.0, to evaluate COM during the walk. To measure the displacement of COM, we used the difference in value between the maximal angle and the minimum anterior-posterior (AP), mediolateral (ML), and rotational angles during the walk. Results: For the normal persons, there was significant correlation between the AP and AP of SMAP, and was also a significant correlation between rotational angle and the ML of SMAP. In the stroke patients, there was significant correlation between AP and ML, and the rotational angle of SMAP. Conclusion: Our research results suggest that if the SMAP system is reinforced in the case of patients who have a greater displacement of COM, it may be used as an evaluation tool during walking.

• 한국항공우주학회지
• /
• 제47권2호
• /
• pp.98-106
• /
• 2019

인간동력항공기의 날개는 고세장비의 형상을 가지고 있어 큰 굽힘변위가 발생한다. 본 논문에서는 고세장비 형상의 날개가 가지는 구조적인 한계를 붙임각을 변경함으로써 개선하고자 하였다. 날개의 익형 및 단면형상을 고정시킨 후 동일 수준의 양력 발생을 만족시킨다는 전제하에 붙임각의 변경에 따른 날개 끝단의 굽힘변위 변화 경향을 관측하였다. 이를 위해 유한날개의 양력, 항력, 모멘트 하중을 날개의 각 섹션에 분포시켰다. 그리고 EDISON의 "geometrically exact beam (GEB)" 프로그램과 "Variational Asymptotic Beam Sectional Analysis (VABS)" 단면해석 프로그램을 사용하여 변경된 설계안의 구조 안전도를 평가하였다. 또한, 다물체 동역학 해석 프로그램 DYMORE를 이용하여 본 논문에서 예측한 날개의 끝단 변위 예측값을 비교 검증하였다.

• 한국지반환경공학회 논문집
• /
• 제12권11호
• /
• pp.39-49
• /
• 2011

본 연구는 대각선 병설터널의 건설로 인한 응력과 변위 특성을 연구하였다. 이 연구에서 그 특성들이 터널의 직경(D)는 13m 그리고 지반은 풍화암으로 가정하여 해석하였다. 해석에서 pillar 폭은 2.0D, 2.5D, 3.0D, 토피고는 3D, 4D, 5D, 그리고 대각선 병설터널의 설치각도 $15^{\circ}$, $30^{\circ}$, $45^{\circ}$로 변화시켰다. 그리고 해석에 사용한 프로그램은 지반 공학적 문제해석에 널리 사용되고 있는 FLAC을 사용하여 발생하는 숏크리트 및 록볼트 응력과 주변지반 변위를 대각선 병설터널의 pillar 폭, 토피고, 그리고 설치각도에 따라 구하고 분석하였다. 그 결과 풍화암 지반에서는 pillar 폭 2.0D이상, 토피고 5.0D이상, 그리고 대각선 병설터널의 설치각도가 적을수록 주변 지반에 영향을 덜 미치고 터널의 안정에 유리한 것으로 나타났다.

• Physical Therapy Rehabilitation Science
• /
• 제12권3호
• /
• pp.240-250
• /
• 2023

Objective: The purpose of this study was to characterize the movement of adjacent segments that occurred when posteroanterior joint mobilization was applied to the 3rd lumbar and thereby to provide basic clinical data. Design: Randomized controlled trial design. Methods: While the subjects were receiving posteroanterior joint mobilization of the 3rd lumbar vertebra, LD (lumbar displacement), LID (lumbar intervertebral distance), LIA (lumbar intervertebral angle), and LLA (lumbar lordosis angle) were measured using X-ray, and the data were then analyzed. Changes before and after posteroanterior joint mobilization were analyzed using a paired-sample t-test, and a one-way ANOVA of variance was performed to determine the difference between segmental movements. In addition, Pearson's correlation analysis was performed to determine the correlation between segmental movements. Results: The results revealed that there was a significant change in LD before and after the application of joint mobilization of the 3rd lumbar in all lumbar vertebrae (p<0.000), among which the 2nd lumbar vertebra, an adjacent segment, showed the most significant change. A significant change in LIA angle was observed in all segments (p<0.000), with the most significant change observed between the 2nd and 3rd lumbar vertebrae. There was a significant change in LLA before and after the application of posteroanterior joint mobilization (p<0.000). The correlation analysis showed a high correlation between displacement of the 3rd lumbar vertebra and displacement of all the other lumbar vertebrae. Conclusions: The presence of kinematic movements of the lumbar vertebrae when segmental movements were generated through the application of posteroanterior joint mobilization of the 3rd lumbar vertebra.

• 터널과지하공간
• /
• 제18권6호
• /
• pp.447-456
• /
• 2008

노천광산에서 사면설계는 안정성과 경제성 측면에서 동시에 접근하여 결정해야 한다. 또한 일반 도로나 철도 연변의 사면과는 달리 대부분 지보나 보강없이 굴착해야 하기 때문에 사면각도가 가장 중요한 설계 변수이다. 본 연구에서는 인도네시아 파시르에 위치한 노천채광방식의 대규모 석탄광산 사면에 대하여 안정성 측면에서의 사면 각도 및 한계사면높이를 결정하였으며 이러한 설계가 가지고 있는 불확실성을 보완할 수 있는 계측 및 계측자료 해석을 수행하였다. 연구 결과, 사면각도(Overall Elope angle) $30^{\circ}$를 유지하는 경우 안전율 1.5를 확보하는 최대개발심도는 $353{\sim}438m$로 계산되었으나 강도정수에 대한 민감도분석결과를 고려할 때 사면높이는 300m를 초과하지 않는 것이 바람직하다. 또한 변위계측자료에 대한 역변위속도 분석 결과가 현장사면 사례와 잘 일치하여 이 방법을 통해 사면의 불안정성 및 파괴시기를 대략적으로 예측할 수 있을 것으로 판단된다.

• 대한족부족관절학회지
• /
• 제14권2호
• /
• pp.157-160
• /
• 2010

Purpose: The purpose of this study is to find out the correlation factors for prognosis of calcaneal fractures. Materials and Methods: 120 cases (feet) of calcaneal fractures, all of them followed up for more than 1 year after surgical procedures, consisted of 101 men (105 feet) and 13 women (15 feet) were reviewed retrospectively. The collected clinical data were as follows : injury mechanism, surgical procedures, time to procedure, time to work and the radiologic data: Bohler angle, heel width, displacement of posterior facet. AOFAS hindfoot score and VAS score were checked. With ANOVA test and multiple regression analysis, the data processed statistically. Results: According Sanders classification, type II was 37 cases (31%), type III 66 cases (55%), and type IV 17 cases (14%). On plane radiography, the Bohler angle improved to average 28.4 degree from 5.6 degree, and the displacement of posterior facet was corrected to average 1.2 mm. AOFAS hindfoot score was checked average 81.7 points postoperatively, and the meaningful difference existed between types of Sanders classification. The Bohler angle represented the outline of the calcaneus had the better correlation with the clinical outcome of calcaneal fractures rather than the anatomical reduction of the posterior facet did. And the width of calcaneus had good correlation with the clinical score. Conclusion: We should also concern about the outline of calcaneus, the width of calcaneus and the Bohler angle representing anatomical reduction, not only the acute reduction of the posterior facet.

• The Journal of Korean Physical Therapy
• /
• 제23권6호
• /
• pp.9-14
• /
• 2011

Purpose: The pelvic tilting exercise is a well recognized rehabilitation maneuver. However, little information is available on the changes of lumbar segmental motion during pelvic tilting. This study was conducted to measure the kinematics of the pelvic tilting exercise on the supine and prone positions via fluoroscopy. Methods: A total of 10 female subjects were enrolled. During anterior, neutral, and posterior pelvic tilting, radiographs were taken in each exercise via fluoroscopy (ARCADIS Orbic, Siemens, USA). Images were sent to the picture archiving communication system (PACS), and the digitized images were analyzed using LabVIEW software (National Instruments, USA). Lumbosacral lordosis and the intervertebral body angle, intervertebral disc angle, and intervertebral displacement were analyzed. Results: The results of lumbar kinematic analysis during three tilting postures in the supine and prone positions demonstrated that lumbosacral lordosis and the intervertebral body angle and intervertebral disc angle were significantly higher when the pelvis was tilted anteriorly (p>0.05). However, there was no significant difference between anterior and neutral tilting in the intervertebral disc angle at the L3/4 level in the prone position (p>0.05), and there was no significant difference among tilting positions in intervertebral body displacement in the prone position (p>0.05). Conclusion: This study provides scientific evidence about the pelvic tilting exercise in lumbosacral segmental motion. Depending on the pelvic tilting exercise, kinematic changes were demonstrated in both positions, especially in the supine position. It is suggested that the supine position is effective for mobility, but it should be used carefully for the LBP (Low back pain) patient with hypermobility.