• 한국수자원학회논문집
• /
• 제31권2호
• /
• pp.177-187
• /
• 1998

하천과 대수층이 연결된 계에서 분산오염원이 유입될 경우에 지하수 수질을 평가할 수 있는 공간적분모형을 제안하였다. 제안된 공간적분모형은 불포화대의 영향이 고려되었으며, 다양한 수문 및 대수층 모의 조건에서 Richards 방정식과 이송-분산 방정식의 공간분포모형에 대한 수치해와 비교를 통하여 공간적분모형을 테스트하였다. 비교 결과에 의하면, 분산도비와 대수층의 두께가 큰 경우를 제외하고는 공간적분모형과 공간분포모형사이의 포화대수층의 평균농도 및 지하수유출의 평균농도는 일치된 반응을 보여주고 있다. 그리고 분산도비와 대수층의 두께가 큰 계에서는 비선형 공간적분모형이 선형 공간적분모형보다 더 좋은 결과를 보여주었다.

• 한국분말재료학회지
• /
• 제25권2호
• /
• pp.120-125
• /
• 2018

Boron nitride nanotubes (BNNTs) are receiving great attention because of their unusual material properties, such as high thermal conductivity, mechanical strength, and electrical resistance. However, high-throughput and high-efficiency synthesis of BNNTs has been hindered due to the high boiling point of boron (${\sim}4000^{\circ}C$) and weak interaction between boron and nitrogen. Although, hydrogen-catalyzed plasma synthesis has shown potential for scalable synthesis of BNNTs, the direct use of $H_2$ gas as a precursor material is not strongly recommended, as it is extremely flammable. In the present study, BNNTs have been synthesized using radio-frequency inductively coupled thermal plasma (RF-ITP) catalyzed by solid-state ammonium chloride ($NH_4Cl$), a safe catalyst materials for BNNT synthesis. Similar to BNNTs synthesized from h-BN (hexagonal boron nitride) + $H_2$, successful fabrication of BNNTs synthesized from $h-BN+NH_4Cl$ is confirmed by their sheet-like properties, FE-SEM images, and XRD analysis. In addition, improved dispersion properties in aqueous solution are found in BNNTs synthesized from $h-BN+NH_4Cl$.

• 한국산학기술학회논문지
• /
• 제5권6호
• /
• pp.558-561
• /
• 2004

암모늄헵타몰리브데이트(ammonium heptamolybdate, AHM)를 전구체로 제조한 실리카 담지 몰리브드늄$(MoO_{3}/SiO_{2})$ 촉매의 구조적 특성을 x-ray 회절기(XRD)를 사용하여 자세히 고찰하였다. 몰리브드늄의 표면담지량은 0.2부터 4.0 atoms $Mo/nm^{2}$로 변화하였으며, 담지촉매의 소성온도는 $300\~500^{\circ}C$로 변화하여 열역학적으로 형성 가능한 모든 몰리브드늄산화물의 구조를 고찰하였다. 담지량이 큰 경우(4 atoms $Mo/nm^{2}$), $300^{\circ}C$소성에서는 뭉쳐있거나 잘 분산된 hexagonal 형태의 결정체가 형성되었으며, $500^{\circ}C$로 소성온도를 증가하면 뭉친 orthorhombic 형태의 $MoO_{3}$ 결정체가 형성되었다. 뭉친 orthorhombic 형태의 결정체는 담지량이 1.1 atom $Mo/nm^{2}$이상이 되면 형성된 반면 잘 분산된 hexagonal 형태의 결정체는 가장 큰 표면 담지량 4.0 atoms $Mo/nm^{2}$에서도 고찰하기가 어려웠다. 이러한 hexagonal 결정체의 담체 표면에서의 높은 분산은 암모니아로 인한 몰리브드늄 산화물($MoO_{3}$)과 실리카($SiO_{2}$) 담체 사이의 강한 표면작용에 기인한 것으로 생각된다.

• 접착 및 계면
• /
• 제16권2호
• /
• pp.55-62
• /
• 2015

자외선 경화를 통한 2-EHA/AA 점착제 제조 시 나노 충전제로 실리카를 도입하는 경우 실리카의 표면 처리 여부와 실리카 함량이 점착제의 점착 물성 및 열 안정성에 미치는 영향을 조사하였다. 또한 서로 다른 반복단위 길이를 가진 경화제에 따른 실리카의 보강 효과 차이도 관찰하였다. 실란으로 표면 처리된 실리카의 경우 실리카 표면과 고분자 매트릭스 간 계면 상호 작용으로 고분자 매트릭스 내 분산 정도를 높여 겔 함량의 저하 없이 0.3 wt%의 농도까지 점착 물성을 증가시키는 것으로 확인되었다. 특히 경화제로 PEGDMA를 사용할 때 분자 내 상대적으로 긴 에틸렌옥사이드 반복단위에 기인하는 분자 유연성으로 EGDMA를 사용한 계에 비해 실리카 보강 역할에 더 긍정적인 것으로 나타났다. 또한 열 분해 후 잔존량을 통해 실리카와 고분자 간 강한 계면 결합으로 인한 열 장벽 효과로 점착제의 열 안정성이 향상되는 것을 알 수 있었다.

• Elastomers and Composites
• /
• 제50권2호
• /
• pp.110-118
• /
• 2015

In this study, diethylaminoethyl methacrylate-styrene-butadiene terpolymer (DEAEMA-SBR), in which diethylaminoethyl methacrylate (DEAEMA) was introduced to the SBR molecule as a third monomer, was synthesized by cold emulsion polymerization. It is expected that amine group introduced to a rubber molecule would improve dispersion of silica by the formation of hydrogen bond (or ionic coupling) between the amine group and silanol groups of silica surface. The chemical structure of DEAEMA-SBR was analyzed using proton nuclear magnetic resonance spectroscopy (H-NMR), Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC) and differential scanning calorimetry (DSC). Then, various properties of DEAEMA-SBR/silica composite such as crosslink density, bound rubber content, abrasion resistance, and mechanical properties were evaluated. As a result, bound rubber content and crosslink density of DEAEMA-SBR/silica compound were higher than those of the SBR 1721 composite. Abrasion resistance and moduli at 300% elongation of the DEAEMA-SBR/silica composite were better than those of SBR 1721 composite due to the high bound rubber content and crosslink density. These results are attributed to high affinity between DEAEMA-SBR and silica. The proposed study suggests that DEAEMA-SBR can help to improve mechanical properties and abrasion resistance of the tire tread part.

• Elastomers and Composites
• /
• 제51권2호
• /
• pp.81-92
• /
• 2016

1,3-Diphenylguanidine (DPG) is commonly used as a secondary accelerator which not only acts as booster of cure but also activating silanization reaction. The aim of this study is to increase the interaction between silica and rubber by using DPG. In this study, mixing was proceeded in two steps. The T-1 compound is mixed DPG with silica and silane coupling agent in the kneader at high temperature which is named as $1^{st}$ mixing step. T-3 compound is mixed DPG with curatives in the two-roll mill at low temperature which is named as $2^{nd}$ mixing step. The T-2 compound is mixed a half of DPG in $1^{st}$ mixing step and the remainder is mixed in $2^{nd}$ mixing step. Total DPG content was equal for all compounds. When DPG is mixed with silica, silane coupling agent during the $1^{st}$ mixing step, a decrease in cure rate and an increase in scorch time can be seen. This indicates that DPG is adsorbed on the surface of silica. during rubber processing. However, bound rubber content is increased and dynamic properties are improved. These results are due to the highly accelerated silanization reaction. However, there are no significant difference in 100%, 300% modulus.

• Bulletin of the Korean Chemical Society
• /
• 제34권11호
• /
• pp.3227-3232
• /
• 2013

A novel Cu-Co-O composite nanocatalyst was designed and prepared for the ozonation of phenol. A synergistic effect of copper and cobalt was observed over the Cu-Co-O composite nanocatalyst, which showed higher activity than either copper or cobalt oxide alone. In addition, the Cu-Co-O composite revealed good activity in a wide initial pH range (4.11-8.05) of water. The fine dispersion of cobalt on the surface of copper oxide boosted the interaction between catalyst and ozone, and the surface Lewis acid sites on the Cu-Co-O composite were determined as the active sites. The Raman spectroscopy also proved that the Cu-Co-O composite was quite sensitive to the ozone. The trivalent cobalt in the Cu-Co-O composite was proposed as the valid state.

• 한국결정학회:학술대회논문집
• /
• 한국결정학회 2003년도 춘계학술연구발표회
• /
• pp.8-8
• /
• 2003

Electron-phonon interaction plays a significant role in forming of colossal magnetoresistance effect (CMR). Polaron formation was observed by neutron diffraction and by extended X-ray absorption fine structure (EXAFS) analysis. Local probe as given by the EXAFS is a useful method to study the polaronic charge and its dependence on temperature and ions size. Here we present the EXAFS study of polaronic charge in La/sub 0.7/Ca/sub 0.3-X/Ba/sub X/MnO₃ compositions. The single phase La/sub 0.7/Ca/sub 0.3-X/Ba/sub X/MnO₃ manganites (x=0; 0.03; 0.06, ..., 0.3) were prepared by ceramic technology [1]. The Curie temperature was determined by extrapolation of the temperature dependence of the magnetization (down to zero magnetization). EXAFS experiments were carried out at the 7C EC beam line of the Pohang Light Source (PLS) in Korea. The atomic pair distribution functions (PDF) were obtained by re-regularization method [2] from filtered spectra. The PDF for the x=0.3 sample showed a single peak function and for x=0.0, 0.03, 0.06, 0.09, 0.12 compositions were asymmetric in agreement with a small Jahn-Teller elongation of two (short and long) bonds of the MnO/sub 6/ octahedron. Dispersion, σ/sub Min-O//sup 2/, and asymmetry, σ/sub Min-O//sup 3/, of the Mn-O bond distances varied significantly with x and showed a maximums at x=0.09. The maximum of σ/sub Min-O//sup 2/ is caused by increase of dynamic rms displacements of the Mn-O distances near the T/sub C/. The observed x dependence of σ/sub Min-O//sup 3/ reflects the reduction of charge carriers mobility at approaching to T/sub C/ from low as well as high temperatures.

• Bulletin of the Korean Chemical Society
• /
• 제27권12호
• /
• pp.1989-1996
• /
• 2006

The $NiSO_4/CeO_2-ZrO_2 $catalysts containing different nickel sulfate and $CeO_2$ contents were prepared by the impregnation method, where support, $CeO_2-ZrO_2$was prepared by the coprecipitation method using a mixed aqueous solution of zirconium oxychloride and cerium nitrate solution followed by adding an aqueous ammonia solution. No diffraction line of nickel sulfate was observed up to 20 wt %, indicating good dispersion of nickel sulfate on the surface of $CeO_2-ZrO_2$. The addition of nickel sulfate (or $CeO_2$) to $ZrO_2$ shifted the phase transition of $ZrO_2$ from amorphous to tetragonal to higher temperatures because of the interaction between nickel sulfate (or $CeO_2$) and $ZrO_2$. A catalyst (10-$NiSO_4/1-CeO_2-ZrO_2$) containing 10 wt % $NiSO_4$ and 1 mole % $CeO_2$, and calcined at $600{^{\circ}C}$ exhibited a maximum catalytic activity for ethylene dimerization. The catalytic activities were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The role of $CeO_2$was to form a thermally stable solid solution with zirconia and consequently to give high surface area, thermal stability and acidity of the sample.

• 폴리머
• /
• 제38권3호
• /
• pp.307-313
• /
• 2014

Poly(ethylene-co-vinyl acetate) (EVA) 중에 포함된 비닐아세테이트의 함량을 0~40 wt% 범위에서 변화시키면서, 관능화 그래핀 쉬트(functionalized graphene sheet, FGS)/EVA 복합재료의 물성 변화를 조사하였다. EVA 중 극성을 가진 비닐아세테이트의 함량이 증가할수록 FGS와의 혼화성이 증가하여, FGS의 분산이 좋아지면서 EVA의 표면 저항 감소, 모듈러스 증가가 효과적으로 발현되었다. EVA 중 비닐아세테이트의 함량이 적어 FGS와의 상호작용이 작은 경우는 계면에서의 접착력이 낮아 인장력을 부가한 경우 파괴가 급격히 진행되어 파괴점에서의 신도가 크게 감소하였다. 복합재료에서 EVA의 결정화는 FGS와의 상호작용으로 대체적으로 감소하였다. 하지만, 비닐아세테이트 함량이 작은 EVA에 소량의 FGS를 첨가한 경우는 기핵효과에 의한 결정화 촉진이 관찰되었다.