• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.169-172
• /
• 2004

This paper proposes a new MR(magneto-rheological) brake utilizing composite modes of MR fluid. Its basic structure and design scheme are almost the same with the conventional MR brake, but for slots in a rotating disk or shell. The slots enable the proposed MR brake to use a new mode, so-called, ‘direct cutting chain mode’as well as shear mode, which results in increasing the braking force(almost 150% compared to the case without slots). Some experimental results show that the proposed MR brake provide the sufficient braking force to be adopted for small portable force feedback devices.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.26-31
• /
• 2000

There are various noises generated by friction. Among the rest, eliminating squeal noise generated during braking is an important task for the improvement of vehicle passengers' comfort. The parameters affecting brake squeal noise are the material properties of the braking pad, the dynamic properties of the brake parts and the dimensions of the brake assembly etc. Also, the squeal noise changes its inherent form with the normal load and sliding speed. In this study, the characteristics of brake squeal noise generated by friction is analyzed experimentally. The experiment focused on the analysis of friction self-excited vibration and squeal noise level. Friction self-excited vibration is caused by the dry friction between pads and rotor, and occurs as a function of their relative sliding speeds. And Friction self-excited vibration is raised the brake squeal noise.

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.779-786
• /
• 2002

The Friction Brake Pad of High Speed Train is the most important parts in brake system, which is usually made of Cu-based Sintered friction material. This study has been carried out about the formulation effects of sintered friction material and made lots of sample brake pads. Then, we have done the performance test of the developed product by using full scale inertia Dynamo-meter. This performance test (braking speed 300km/h) was conducted as GEC Alsthom Standard test procedure and High Speed Brake Test (braking speed 350km/h) was done at "Poli" in Italy. The friction properties of this product was almost identical with the brake pad which is currently used to TGV. And the temperature of brake disk on braking speed 350Km/h was a little higher.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1943-1952
• /
• 2011

Rail vehicle brakes partly or completely transform the kinetic energy of moving vehicles into other forms of energy, in order to reduce the speed, and if necessary to bring them to a halt. To fulfil these requirements, the effect of a certain brake force is necessary and especially it is considered that the brake force is a important device to rail vehicles as a mass transit. The brake distance is a criterion for measuring brake force. The brake force is measured via dozens of brake distance test before its service operation. The brake distance is influenced by cars and rail conditions; weight of cars, speed on the verge of braking, temperature of brake disk and condition of the upper side of rail, etc. Therefore we will study how the these factors impact with the brake distance via a real test results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.607-612
• /
• 2004

Disc brake noise continues to be a major concern throughout the automotive industry despite efforts to reduce its occurrence. Eliminating vibrations during braking is an important task for both vehicle passenger comfort and reducing the overall environmental noise levels. There are several classes of disc brake noise, the major ones being squeal, judder, groan, and moan. In this study, analytical model for moan noise of rear disk brake is investigated. Modeling of the disc brake assembly to take account of the effect of different geometrical and contact parameters is studied through the use of multi-body model. The contact stiffness of the caliper and torque member plays an important role in controlling brake vibration. Therefore, a suitable material pair at the caliper/body contact has been made. An ADAMS model of a rear disc brake system was integrated with a flexible suspension trailng arm from MSC/NASTRAN. A fully non-linear dynamic simulatin of brake system behavior, containing rigid and flexible bodies, was performed for a Prescribed set of operating conditions. Simulation results were validated using data from vehicle experimental testing.

• Tribology and Lubricants
• /
• v.18 no.2
• /
• pp.127-132
• /
• 2002

The Taguchi method, a robust experimental design, was used to optimize manufacturing parameters of a brake lining during hot pressing and heat treatment. A friction material containing 15 ingredients was employed fur this experiment and friction and wear tests were carried out by using a pad-on-disk type tribotester. Sixteen brake linings with different manufacturing conditions were examined according to a parameter design. From the results of the signal-to-noise (S/N) ratio and the analysis of variance (ANOVA), the cause and effect of the manufacturing parameters on physical properties (hardness and porosity) and friction and wear characteristics of brake linings was obtained.

• Journal of the Korean Society for Railway
• /
• v.11 no.2
• /
• pp.188-194
• /
• 2008

Brake disks for rolling stock are exposed to thermal fatigue during braking, and thermal cracks occur on surface of disks. Thermal cracks can cause serious accidents, deterioration of braking performance and increase of maintenance cost due to frequent exchange of friction materials. In this study, candidate materials with high-heat resistance were selected by searching the literature. By using cast specimens made of the candidate materials, chemical composition, crystal structure and graphite type were analyzed. In addition, friction coefficient and wear were measured and compared with values for the disk material in service. As a result, it was shown that the NiCrMo has highest tensile strength and lowest friction coefficient and the disk material in service has the most stable friction characteristics.

• Journal of Mechanical Science and Technology
• /
• v.14 no.3
• /
• pp.320-330
• /
• 2000

It is desirable to perform nondestructive evaluation (NDE) to assess material properties and part homogeneity because the manufacturing of carbon/carbon brake disks requires complicated and costly processes. In this work several ultrasonic techniques were applied to carbon/carbon brake disks (322mm ad, 135mm id) for the evaluation of spatial variations in material properties that are attributable to the manufacturing process. In a large carbon/carbon disk manufactured by chemical vapor infiltration (CYI) method, the spatial variation of ultrasonic velocity was measured and found to be consistent with the densification behavior in CYI process. Low frequency (e.g., 1-5MHz) through-transmission scans based on both amplitude and time-of-flight of the ultrasonic pulse were used for mapping out the material property inhomogeneity. Images based on both the amplitude and the time-of-flight of the transmitted ultrasonic pulse showed significant variation in the radial direction. The radial variations in ultrasonic velocity and attenuation were attributed to a density variation caused by the more efficient densification of pitch impregnation near the id and od and by the less efficient densification away from the exposed edged of the disk. Ultrasonic velocities in the edges of the disk. Ultrasonic velocities in the thickness direction were also measured as a function of location using dry-coupling transducers ; the results were consistent with the densification behavior. However, velocities in the in-plane directions (circumferential and radial) seemed to be affected more by the relative contents of fabric and chopped fiber, and less by the void content.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.792-797
• /
• 2007

This study investigates the change of the temperature and fatigue property of the braking disk (GC25-30 material) for the railway vehicle. The average temperature is measured about $100^{\circ}C$ and the maximum temperature is measured over $200^{\circ}C$ by non-contact sensor from Seoul to Chun-an. In the $20^{\circ}C-300^{\circ}C$. The Fatigue tests did for new and used disk specimens. The fatigue test results of new disk specimens were similar due to the temperature change. But the compare of specimens between new disk and old disk, The fatigue life of old disk specimens was smaller than new disk specimens about 10%.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.5
• /
• pp.444-451
• /
• 2020

This study was conducted to develop the hydraulic brake assembly for MUAV(Medium-altitude Unmanned Aerial Vehicle). The brake assembly has the self-gap adjuster which performs to maintain a constant gap between the piston and the disk, even if the friction pad wore down. The function of adjuster helps to keep the brake-reaction speed constant and prevent the unnecessary abrasion of the wear pad during the life of the brake assembly. The development of the aircraft hydraulic brake assembly with the self-gap-adjuster in this paper is the first ever in South Korea. The concept of the mechanism was defined and the formula which is necessary to calculate the friction force was set up in the paper. The tester was invented for the functional test and the proper operation of the self-gap-adjuster was confirmed through the test. Dynamo tests and flight tests were also carried out to verify the braking performance of the brake assembly.