Layer-by-layer 방법을 기초로 기존의 방법보다 간단히 합성된 껍질 두께를 달리한 속이 빈 구형체인 폴리아닐린과 폴리피롤을 리튬이차전지 양극 활물질로 사용하여 껍질 두께에 따른 방전용량에 미친 효과를 조사하였다. 유화중합으로 중합된 음이온계 계면활성제에 의해 표면 개질 된 폴리스타이렌을 지지체로 사용하였다. 아닐린과 피롤의 모노머 양을 각각 다르게 추가하여 합성하여 쉘 두께를 조절하였다. 그 후, 유기용매를 통해 폴리스타이렌을 제거하여 속이 빈 구형체를 제조하였다. 이는 리튬이차전지에서 전해액과의 접촉을 증가시키기 위해 넓은 표면적을 가진 속이 빈 구형체 구조로 제조하고, 분자량 조절이 어렵고 단위부피당 질량이 낮아 용량이 낮은 단점을 가진 고분자를 껍질 두께의 조절로 단점을 보완하고자 하였다. 아닐린 모노머 양을 1.2, 2.4, 3.6, 4.8 및 6.0 mL로 증가시킨 경우 폴리아닐린의 껍질 두께는 30.2, 38.0, 42.2, 48.2 및 52.4 nm이고 피롤 모노머 양이 0.6, 1.2, 2.4 및 3.6 mL일 경우 양극재료는 폴리아닐린의 경우 껍질 두께가 30.2, 42.2 및 52.4 nm 일 때, 10회 후, 방전 용량은 약 ~18, ~29 및 ~62 mAh/g으로 나타났으며, 폴리피롤의 경우 껍질 두께가 16.0, 22.0, 27.0 및 34.0 nm 일 때, 15회 후, 방전용량은 약 ~15, ~36, ~56 및 ~77 mAh/g으로 껍질의 두께가 증가할수록 방전용량 역시 증가하는 것을 알 수 있었다.
Sulfur-substituted $LiMn_{0.9}Cr_{0.1}O_{2-x}S_x$$(0\;\leq\;x\;\leq\;0.1)$ layered oxides have been prepared by solid state reaction under inert atmosphere. From powder X-ray diffraction analyses, all the present lithium manganates were found to be crystallized with monoclinic-layered structure. Electrochemical measurements clearly demonstrated that, in comparison with the pristine $LiMn_{0.9}Cr_{0.1}O_2$, the sulfur-substituted derivatives exhibit smaller discharge capacities for the entire cycle range but the recovery of discharge capacity after the initial several cycles becomes faster upon sulfur substitution. The effect of the sulfur substitution on the chemical bonding nature of $LiMn_{0.9}Cr_{0.1}O_{2-x}S_x$has been investigated using X-ray absorption spectroscopic (XAS) analyses at Mn and Cr K-edges. According to Mn K-edge XAS results, the trivalent oxidation state of manganese ion remains unchanged before and after the substitution whereas the local structure around manganese ions becomes more distorted with increasing the substitution rate of sulfur. On the other hand, the replacement of oxygen with sulfur has negligible influence on the local atomic arrangement around chromium ions, which is surely due to the high octahedral stabilization energy of $Cr^{+III} $ ions. Based on the present experimental findings, we have suggested that the decrease of discharge capacity upon sulfur substitution is ascribable to the enhanced structural distortion of $MnO_6$ octahedra and/or to the formation of covalent Li-S bonds, and the accompanying improvement of cyclability would be related to the depression of Mn migration and/or to the pillaring effect of larger sulfur anion.
In this study, we carry out a study on how to improve performance of vanadium redox flow battery (VRFB) through promoting reaction rate of rate determining vanadium reaction ($[VO]^{2+}/[VO_2]^+$). In order to do that, three different carbons like Vulcan (XC-72), CMK3 and MSU-F-C are adopted as the catalysts, while their catalytic activity and reaction reversibility are evaluated using half-cell tests. Their topological images are also measured by TEM. For estimation of the VRFB performance, multiple charge-discharge curves of VRFBs including the catalysts are measured by single cell tests. As a result of that, MSU-F-C shows relatively excellent catalytic activity and reaction reversibility as well as large surface area compared to those of Vulcan (XC-72) and CMK3. Also, in terms of the performance of VRFBs including the catalysts, VRFB including MSU-F-C indicates (i) low charging/discharging overpotentials and low internal resistance, (ii) high charge/discharge capacities and (iii) high energy efficiency. These VRFB performance data are well agreed with results on catalytic activity and reaction reversibility. The reason that MSU-F-C induces superior VRFB performances is attributed to (i) its large surface area and (ii) its hydrophilic surface functional groups that mainly consist of hydroxyl bonds that are supposed to play active surface site role for facilitaing $[VO]^{2+}/[VO_2]^+$ redox reaction. Based on the above results, it is found that adoption of MSU-F-C as catalyst for VRFB results in improvement in VRFB performance by promoting the languid $[VO]^{2+}/[VO_2]^+$ redox reaction.
본 연구에서는 낙동강수계 다목적댐의 용수공급능력을 재평가해보고, 감소된 공급능력을 보완하기 위한 방안으로 '보'를 포함한 용수공급능력과 연계운영 방안을 검토하였다. 연구 대상은 낙동강 5개 다목적댐(안동, 임하, 합천, 남강, 밀양)과 8개 보(상주, 낙단, 구미, 칠곡, 강정고령, 달성, 합천창녕, 창녕함안)로 하였다. 먼저, 기존댐의 용수공급능력 재평가는 각 댐의 설계당시 평가 기준을 준용하여 HEC-5로 모의하였으며, 입력 자료는 준공 이후 각 댐별로 축적된 유입량 자료를 활용하였다. 모의 결과, 3개 댐의 공급능력이 73~87% 수준으로 감소했음을 확인할 수 있었다. 보를 포함한 용수공급능력의 효과를 확인하기 위해서, 각 댐별 모의, 댐간 연계운영 모의, 댐-보 연계운영 모의 등 세가지 case에 대해 HEC-ResSim 모형을 활용하여 비교 검토하였다. 이수안전도 95%를 적용하기 위해 20개년(1992~2011년) 중 1회 물부족을 허용하는 것으로 하였으며, 보는 축적된 유입량 자료가 없어, 전국유역조사(국토교통부)의 장기유출 모의자료(PRMS)에 댐 방류량 자료를 결합하여 활용하였다. 연계운영 모의시 왜관 수위표 지점을 기준으로 낙동강 상 하류를 구분하여 연계운영 네트워크를 구성하였다. 3가지 case에 대한 모의 결과, 댐별 운영시 24억$m^3$/년, 댐간 연계운영시 26억$m^3$, 댐-보 연계운영시 27억$m^3$/년의 용수공급이 가능한 것으로 평가되었다. 즉, 보를 포함하여 용수공급을 할 경우 연간 1.2억$m^3$ 가량의 추가 공급이 가능하여, 댐 설계당시 용수공급 계획량(27억$m^3$/년)과 같은 수준의 공급이 가능할 것으로 판단된다.
Lithium secondary batteries have become an important power source for portable electronic devices such as cellular phones, laptop computers. Presently, commercialized lithium-ion batteries use a LiCoO2 cathode. However, due to the high cost and environmental problems resulting from cobalt, an intensive search for new electrode materials is being actively conducted. Recently, solid solution LiMn1-xNixO2 have become attractive because of high capacity and enhanced safety at high voltages over 4.5 V. The Li1.6Ni0.35Mn0.65O2 compounds were conventionally prepared by a sol-gel method, which can produce the layered Li-Ni-Mn-O compounds with a high homogeneity. And by adding a graphene 2wt% the first charge-discharge voltage profiles was increased over Li1.6Ni0.35Mn0.65O2 compound. Also, the variation s of the discharge capacities with cycling showed a higher capacity retention rater. In this study, material lifecycle evaluation was performed to analyze the environmental impact characteristics of Li1.6Ni0.35Mn0.65O2 & graphene 2wt% half-cell manufacturing process. The software of material life cycle assessment was Gabi. Through this, environmental impact assessment was performed for each process. The environmental loads induced by Li1.6Ni0.35Mn0.65O2 & graphene 2wt% synthesis process were quantified and analyzed, and the results showed that the amount of power had the greatest impact on the environment.
In the development of new hydrogen absorbing materials for a next generation of metal hydride electrodes for rechargeable batteries, metastable Mg-Ni-based compounds find currently special attention. Amor phous-nanocrystalline $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ alloys were produced by mechanical alloying and melt-spinning and characterized by means of XRD, TEM and DSC. On basis of mechanically alloyed Mg-Ni-Y powders, complex hydride electrodes were fabricated and their electrochemical behaviour in 6M KOH (pH=14,8) was investigated. The electrodes made from $Mg_{63}Ni_{30}Y_7$ powders, which were prepared under use of a SPEX shaker mill, with a major fraction of nanocrystalline phase reveal a higher electrochemical activity far hydrogen reduction and a higher maximum discharge capacity (247 mAh/g) than the electrodes from alloy powder with predominantly amorphous microstructure (216 mAh/g) obtained when using a Retsch planetary ball mill at low temperatures. Those discharge capacities are higher that those fur nanocrystalline $Mg_2Ni$ electrodes. However, the cyclic stability of those alloy powder electrodes was low. Therefore, fundamental stability studies were performed on $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ ribbon samples in the as-quenched state and after cathodic hydrogen charging by means of anodic and cathodic polarisation measurements. Gradual oxidation and dissolution of nickel governs the anodic behaviour before a passive state is attained. A stabilizing effect of higher fractions of yttrium in the alloy on the passivation was detected. During the cathodic hydrogen charging process the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel-species, causing preferential oxidation and dissolution during subsequent anodization. The effect of chemical pre-treatments in 1% HF and in $10\;mg/l\;YCl_3/1%\;H_2O_2$ solution on the surface degradation processes was investigated. A HF treatment can improve their anodic passivation behavior by inhibiting a preferential nickel oxidation-dissolution at low polarisation, whereas a $YCl_3/H_2O_2$ treatment has the opposite effect. Both pre-treatment methods lead to an enhancement of cathodically induced surface degradation processes.
본 연구에서는 MgF2를 이용하여 LiNi0.8Co0.15Al0.05O2 양극활물질의 표면을 코팅하여 전기화학적 특성과 열적 안정성을 평가하였다. 코팅된 MgF2의 비율은 0.5, 1, 3 wt%로 조절하였다. 전기화학적 특성은 CV, 충·방전 프로파일, 출력특성, 수명특성을 분석하였고, 열적 안정성은 DSC 분석을 통하여 이루어졌다. 전기화학적 특성 분석 결과 0.1C에서 초기 방전 용량은 MgF2 코팅이 되었을 때 감소하였지만, 2C까지 출력을 향상 시켰을 때는 약간 향상된 방전 용량을 얻을 수 있었고, 수명특성 또한 향상되었다. 또한 DSC 분석 결과 코팅이 되었을 때 발열 온도가 증가하였고, 발열 피크의 세기 또한 감소하였다.
초음파분무열분해법과 한 단계의 후열처리로 이차상이 없는 Al이 첨가된 $Li(Ni_{1/3}Co_{1/3}Mn_{1/3-x}Al_x)O_2$ (x=0.0, 0.005, 0.01. 0.05) 리튬이차전지용 양극활물질을 합성하였다. 합성된 분말은 Al의 첨가량이 많아짐에 따라서 $I_{003}/I_{104}$ 비는 감소하고 입자가 커지는 경향을 보였다. 상온에서 전류밀도 1C의 rate로 $3.0\sim4.5V$ 범위에서 충방전 시험한 결과, Al 치환량이 0.5와 1.0 at%에서는 초기용량이 180과 $184mAhg^{-1}$으로 치환하지 않았을 때의 $182mAhg^{-1}$과 차이가 없었으며, 싸이클 특성도 치환하지 않은 것과 0.5, 1.0 at% 치환한 조성에서 각각 81, 77, 81%의 방전용량이 유지되었다. 그러나 $3.0\sim4.6V$에서는 치환효과가 확실하게 나타나서, 50 싸이클 후의 치환하지 않은 것의 방전용량은 초기용량의 30%가지 감소한데 비하여 Al을 0.5 at% 치환한 것은 70%를 유지하였다. 치환에 의한 싸이클 특성 향상은 XPS 분석 결과 Al 치환이 $Mn^{3+}$의 양을 감소시켰기 때문인 것으로 사료되었다.
흑연재료를 부극으로 사용하는 리튬2차전지의 유기 전해액으로 propylene carbonate(PC) 용매를 사용하면 흑연층간에 PC의 비가역적 삽입반응으로 인하여 흑연의 exfoliation이 진행된다. 유기전해액으로 ethylene carbonate(EC)를 사용하면 이러한 문제점은 해결되지만, EC의 어는점이 $36.2^{\circ}C$로 높은 것이 단점이다. EC계 전해액에 적정 비율의 PC를 첨가한 혼합 유기 전해액은 전도도가 향상 될 수 있으며, 흑연전극의 exfoliation도 감소시킬 수 있다. EC계 전해액에 첨가한 PC 함량에 따른 유전상수 및 몰전도도를 구하였으며, 동시에 탄소부극에 대한 전기화학적 특성을 조사하였다. $LiPF_6/EC+DEC$ 전해액에 첨가한 PC 함량이 증가하면 유전상수와 몰전도도는 직선적으로 증가하였다. 충방전 시험결과, MCMB-6-28s및 MPCF300의 비가역비용량은 첨가한 PC함량이 $0.83\%$인 경우에는 감소하였으나, 그 이후에는 PC함량에 따라 증가하였다 MPCF3000및 PCG100의 비가역비용량은 PC함량이 $10\%$까지는 50mAh/g이하였다. 그러나, 방전비용량은 첨가한 PC 함량과 관계없이 사용한 탄소재료에 따라서 일정한 값을 나타내었다.
다공성 $Co(OH)_2$ 나노플레이크 박막은 전위제어 전착법을 이용하여 티타늄 메쉬에 여러 전착전위(-0.75, -1.0, -1.2 및 -1.4 V)에서 전착하여 슈퍼커패시터에 이용하였다. 티타늄 메쉬에 전착된 $Co(OH)_2$ 나노플레이크 박막의 두께 및 전착량은 전착전위의 제어에 의해 결정되었고 -1.4 V에서 전착한 $Co(OH)_2$ 나노플레이크 박막의 두께는 약 $34{\mu}m$로 가장 두껍게 전착되었으며 전착량은 17.2 g이다. 전착전위 -0.75, -1.0, -1.2 및 -1.4 V에서 전착한 경우 초기 방전용량은 각각 226, 370, 720 그리고 $1,008mF\;cm^{-2}$으로 나타났고 1,000 사이클 후 각각 206, 349, 586 그리고 $866mF\;cm^{-2}$으로 나타났다. 또한 이들의 용량유지율은 각각 91, 94, 81 및 86%로 나타났다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.