• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.12A
• /
• pp.1156-1164
• /
• 2008

In this paper, we propose a bi-directional coding method (BTC) using time reversal mirror for effective data exchange between mobile stations and basestations. In conventional relay systems, while one node transmits data, other nodes should keep silent to avoid interference. Thus, to interchange data between basestations and mobile stations, it needs four stages. However, using the proposed BTC method, a relay station transmits a probe source before data transmission, and using this information, mobile stations and basestations transmit data to the relay station simultaneously. Therefore, since it exchanges data in only two steps, the system achieves improved system capacity. In addition, owing to no need for complex calculation, the relay system can be implemented with low complexity. The simulation results demonstrate that the proposed method achieves enhanced system capacity.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.11
• /
• pp.1603-1611
• /
• 2021

As IMO environmental regulations are tightened, the need to establish a system that can reduce emissions is increasing, and for this purpose, various power control management systems have been studied and implemented as a new energy management system for ships. In this study, we design a control process through modeling for Bi-Directional Converter (BDC) application with bi-directional power flow to link batteries, which are energy storage devices, to conventional generator power systems, and propose mechanisms for batteries optimized for varying loads. This work models MATLAB/Simulink as a BDC and simulates current control and state of charge (SOC) optimization at the time of charging and discharging batteries according to load scenarios. Through this, the battery, power, and load were interlocked so that the generator operated on board could be operated in the optimal operation range, and power control management was performed to enable the generator to operate in the high fuel efficiency range.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.735-741
• /
• 2003

A simplified view of array design and application process was introduced. Array design is critical to achieve a successful phased array measurements. A planar microphone array is designed to produce optimum performance and also to fit economic requirement in integrating data acquisition system. Certain performance characteristics are of primary concern when designing arrays. These characteristics include array resolution, spatial aliasing and array sidelobe suppression. Every array has its directional pattern that shows such characteristics. Assuming that a monopole source is located in center, beam-patterns have been simulated varying measurement conditions such as number of sensors. array aperture size, distance between array and source, frequency of interest and so on. Sensor correction was conducted on very channel using magnitudes and phased of FRF with respect to a reference microphone channel. Then with a spiral type array, measurements have been made with two point sources of same frequency in order to investigate array resolving abilities. It is observed that higher frequency source achieves better resolution than lower one does.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1360-1365
• /
• 2019

In this paper, we describe a sound source localization(SSL) system which can be applied to mobile robot and automatic control systems. Usually the SSL method finds the Interaural Time Difference, the Interaural Level Difference, and uses the geometrical principle of microphone array. But here we proposed another approach based on the deep neural network to obtain the horizontal directional angle(azimuth) of the sound source. We pick up the sound source signals from the two microphones attached symmetrically on both sides of the robot to imitate the human ears. Here, we use difference of spectral distributions of sounds obtained from two microphones to train the network. We train the network with the data obtained at the multiples of 10 degrees and test with several data obtained at the random degrees. The result shows quite promising validity of our approach.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.221-228
• /
• 2002

Thickness of concrete lining, voids at the back of lining or shotcrete are very important elements for inspecting the safety of tunnels. Therefore, the inspection of tunnel lining structure means to investigate the inner layer boundaries of the structure. For this purpose, seismic reflection survey is the most desirable method if it works in good conditions. However, the conventional seismic reflection method can not be properly used for investigating thin layers in the lining structure. In other words, to detect the inner boundaries, it is desirable for the wavelength of source to be less than the thickness of each layer and for the receiver to be capable of detecting high frequency(ultrasonic) signals. To this end, new appropriate source and receiver devices should be developed above all for the ultrasonic reflection survey. This paper deals primarily with the development of source and receiver devices which are essential parts of field measuring system. Interests are above all centered in both the radiation pattern, energy, frequency content of the source and the directional sensitivity of the receiver. With these newly devised ones, ultrasonic physical modeling has been performed on 3-D physical model composed of bakelite, water-proof and concrete, The measured seismograms showed a clear separation of wave arrivals reflected from each layer boundary. Furthermore, it is noteworthy that reflection events from the bottom of concrete below water-proof could be also observed. This result demonstrates the usefulness of the both devices that can be applied to benefit the ultrasonic reflection survey. Future research is being focus on dealing with at first an optimal configuration of source and receiver devices well coupled to tunnel wall, and further an efficient data control system of practical use.

• Journal of Korea Water Resources Association
• /
• v.45 no.6
• /
• pp.545-555
• /
• 2012

A numerical modeling has become increasingly popular and more important to the study of water waves with a rapid advancement of computer technology. However, different types of problems are induced during simulating wave motion. One of the key problems is re-reflection to a computation domain at the incident boundary. The internal wave generating-absorbing boundary conditions have been commonly used in numerical wave models to prevent re-reflection. For the Navier-Stokes equations model, the internal wave maker using a mass source function of the continuity equation has been used to generate various types of waves. Nonetheless, almost every numerical experiment is performed in two dimensions and only a few tests have been expanded to three dimensions. More recently, a momentum source function of the Boussinesq equations is applied to generate essentially directional waves in the three dimensional Navier-Stokes equations model. In this study, the internal wave maker using a momentum source function is employed to generate targeted linear waves in the three-dimensional LES model.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.3
• /
• pp.197-204
• /
• 2012

In this thesis, studied the method to minimize the changes in frequency response and level due to the variation of the distance from the source to the microphone. selecting three microphones (omni directional, cardioid, super cardioid) which are being used generally, frequency responses were measured in accordance with the distance changes. Gotten the difference from the reference as the result of measurement, changed responses for each frequency range were compensated in comparison of the original human vocal source. In low frequency range, the low frequency boost caused by the proximity effect and decrease in accordance with the distance were compensated. The variation in mid-frequency range is comparatively small, however since the mid-range is the most important part of the human vocal signal, were compensated the mid-frequency range in comparison of the reference. The human vocal signal variation in high frequency range is extremely small and the high frequency is compensated close to the original source without difficulty. Understanding the microphone characteristics and compensations, this study showed that the response can be maintain among the change of the distance from the source to the microphone.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.237-245
• /
• 2003

Since the velocity is dependent on the fiber orientation in anisotropic composites, the application of traditional acoustic emission (AE) source location techniques based on the constant velocity to composite structures has been practically impossible. The anisotropy makes the source location procedure complicated and deteriorates the accuracy of the location. In this study, we have divided the region of interest(ROI) into a set of finite elements, taken each element as a virtual source, and calculated the arrival time differences between sensors by using the velocities at every degree from 0 to 90. The calculated and the experimentally measured values of the arrival time difference aye then compared to minimize the location error. The results from two different materials, namely AA6061-T6 and CFRP(uni-directional; UD, $[0]_{32}4$) laminate confirmed the practical usefulness of the proposed method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.7
• /
• pp.70-76
• /
• 2012

In general, the unidirectional power flow is normal in distribution feeders before activation of distributed power source such as PV. However, the interactive power flow is likely to occur in case of the power system under distributed generation. This interactive power flow can cause an unexpected effect on convectional protection coordination systems designed based only on the unidirectional power flow system. When the power line system encounters a problem, the interactive power flow can be a contributed current source and this makes the fault current bigger or smaller compared to the unidirectional case. The effect of interactive power flow is varied depending on the location of the point to ground fault, relative location of the PV, and connection method. Therefore it is important to analyse characteristics of fault current and interactive flow for various transformer connection and location of the PV. This paper proposes a method of improved protection coordination which can be adopted in the protective device for customers in distribution feeders interconnected with the PV. The proposed method is simulated and analysed using PSCAD/EMTDC under various conditions.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.24 no.1
• /
• pp.1-6
• /
• 1988

For the purpose of making the detection range of fish detection system more longer and computerizing the system a parametric sound source, a timer and a digitizing circuit for the Apple II computer have been studied. The parametric sound of 5 KHz generated by passing AND gate two signals from carrier signal generator of 200KHz with modulator of 5KHz. This parametric acoustic source of 5KHz difference frequency had more higher directional resolution of 10 degrees than single frequency sound of 200KHz. Peripheral interface adaptor MC 6821 was adopted for interfacing to the Apple II personal computer. The timer consisted of six decade binary coded decimal counters (74 LS 190), and the digitizing circuit consisted of a sample and hold (LF 398) and an A/D converter(ADC 0808). The timer with 10KHz clock pulse had the measuring time from 0.1msec to 100sec. This time measuring range was satisfactory for the aim of the fish finding acoustic system.